Dodge Caliber. Manual — part 1302
U1114–LOST COMMUNICATION WITH LEFT FRONT TIRE PRESSURE TRIGGER
MODULE
PM
TIRES/WHEELS - ELECTRICAL DIAGNOSIS
22 - 35
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
•
With the ignition on
•
Battery voltage between 10 and 16 volts
•
IOD fuse installed
•
Set Condition:
If the WCM fails to receive bus messages from the Tire pressure trigger module for two consecutive counts of
trigger module not responding to a communication check.
Possible Causes
(D508) COM - LIN TIRE PRESSURE MONITOR LAN CIRCUIT SHORT TO VOLTAGE
(D508) COM - LIN TIRE PRESSURE MONITOR LAN CIRCUIT SHORT TO GROUND
(D508) COM - LIN TIRE PRESSURE MONITOR LAN CIRCUIT OPEN OR HIGH RESISTANCE
(F202) FUSED IGNITION SWITCH OUTPUT (RUN) CIRCUIT OPEN OR HIGH RESISTANCE
(Z904) GROUND CIRCUIT(S) OPEN OR HIGH RESISTANCE
(D508) COM-LIN TIRE PRESSURE MONITOR LAN CIRCUIT OPEN
TIRE PRESSURE TRIGGER MODULE POWER AND GROUND
WCM
Diagnostic Test
1.
VERIFY DTC IS ACTIVE
NOTE: Ensure the IOD fuse is installed and battery voltage is between 10 and 16 volts before proceeding.
Turn the ignition on.
With the scan tool, read and record WCM DTCs.
With the scan tool, erase WCM DTCs.
Cycle the ignition switch.
With the scan tool, read WCM DTCs.
Does this DTC reset?
Yes
>> Go To 3
No
>> Perform the Stored Lost Communication test procedure. Refer to the table of contents in this section.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING).
Perform BODY VERIFICATION TEST. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES
- STANDARD PROCEDURE).
2.
(D508) COM-LIN TIRE PRESSURE MONITOR LAN CIRCUIT OPEN
Turn the ignition off.
Disconnect the Tire Pressure Trigger Module.
Disconnect the WCM.
With an ohmmeter measure the resistance of the (D508) COM-LIN TIRE PRESSURE MONITOR LAN CIRCUIT.
Is the resistance below 5 Ohms?
Yes
>> Go To 4
No
>> Repair or replace the open circuit.
Perform TPM VERIFICATION TEST. (Refer to 22 - TIRES/WHEELS/TIRE PRESSURE MONITORING -
STANDARD PROCEDURE)
22 - 36
TIRES/WHEELS - ELECTRICAL DIAGNOSIS
PM
3.
(F202) FUSED IGNITION SWITCH OUTPUT (RUN) CIRCUIT OPEN OR HIGH RESISTANCE
Turn the ignition off.
Disconnect the Tire Pressure Transponder harness connector.
Disconnect the Sentry Key Remote Entry Module harness connector.
Turn the ignition on.
Using a 12–volt test light connect to ground, check the (F924) Fused
Ignition Switch Output (Run) circuit.
NOTE: The test light should be illuminated and bright. Compare
the brightness to that of a direct connection to the battery.
Is the test light illuminated and bright?
Yes
>> Go to 5
No
>> Repair the (F924) Fused Ignition Switch Output (Run) circuit
for an open circuit or high resistance.
Perform TPM VERIFICATION TEST. (Refer to 22 - TIRES/
WHEELS/TIRE PRESSURE MONITORING - STANDARD
PROCEDURE)
4.
(Z924) GROUND CIRCUIT(S) OPEN OR HIGH RESISTANCE
Using a 12-volt test light connect to battery voltage, probe each of the
(Z924) Ground circuit(s).
NOTE: The test light should be illuminated and bright. Compare
the brightness to that of a direct connection to the battery.
Does the test light illuminate brightly?
Yes
>> Go to 6
No
>> Repair the (Z924) Ground circuit(s) for an open circuit or
high resistance.
Perform TPM VERIFICATION TEST. (Refer to 22 - TIRES/
WHEELS/TIRE PRESSURE MONITORING - STANDARD
PROCEDURE)
PM
TIRES/WHEELS - ELECTRICAL DIAGNOSIS
22 - 37
5.
(D508) COM - LIN TIRE PRESSURE MONITOR LAN CIRCUIT SHORT TO VOLTAGE
Turn the ignition on.
Measure the voltage of the (D508) COM - LIN Tire Pressure Monitor
LAN circuit.
Is there any voltage present?
Yes
>> Repair the (D508) COM - LIN Tire Pressure Monitor LAN
circuit for a short to voltage.
No
>> Go to 7
Perform TPM VERIFICATION TEST. (Refer to 22 - TIRES/
WHEELS/TIRE PRESSURE MONITORING - STANDARD
PROCEDURE)
6.
(D508) COM - LIN TIRE PRESSURE MONITOR LAN CIRCUIT SHORT TO GROUND
Turn the ignition off.
Measure the resistance between ground and the (D508) COM - LIN Tire
Pressure Monitor LAN circuit.
Is the resistance below 5.0 ohms?
Yes
>> Repair the (D508) COM - LIN Tire Pressure Monitor LAN
circuit for a short to ground.
Perform TPM VERIFICATION TEST. (Refer to 22 - TIRES/
WHEELS/TIRE PRESSURE MONITORING - STANDARD
PROCEDURE)
No
>> Go to 8
22 - 38
TIRES/WHEELS - ELECTRICAL DIAGNOSIS
PM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст