Dodge Caliber. Manual — part 487
*OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST
Diagnostic Test
1.
PERFORM THE OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST
NOTE: Ensure that the battery is fully charged.
NOTE: The Occupant Classification Seat Weights 9077 are required to perform this test.
Remove any special tools or jumper wires and reconnect all previously disconnected components – except the bat-
tery.
WARNING: To avoid personal injury or death, turn the ignition on, then reconnect the battery.
NOTE: Failure to follow the test instructions or aborting the test will cause faults to set when performing
the Occupant Classification Module System Verification Test. To prevent faults due to process errors: verify
that all tests steps that led you here were performed as directed; verify that the ignition is in run; Wait 30
seconds after changing the seat weight before proceeding to allow the system to stabilize; only press scan
tool buttons when directed to do so; and perform the Occupant Classification Module System Verification
Test to completion.
With the scan tool in OCM, select More Options, select System Tests, and select Occupant Classification Module
System Verification Test. Run the test by following the instructions displayed on the scan tool. When the test is
complete, wait two minutes, and then proceed as follows.
With the scan tool, read OCM DTCs.
Does the scan tool display any active PASSENGER SEAT WEIGHT SENSOR DTCs?
Yes
>> Go To 2
No
>> Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1. Diagnostic Test
2.
PERFORM THE OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST
WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Verify that all of the Seat Weight Sensor mounting screws are torqued to specification. Refer to Group 23 for spec-
ification.
WARNING: To avoid personal injury or death, turn the ignition on, then reconnect the battery.
NOTE: Failure to follow the test instructions or aborting the test will cause faults to set when performing
the Occupant Classification Module System Verification Test. To prevent faults due to process errors: verify
that all tests steps that led you here were performed as directed; verify that the ignition is in run; Wait 30
seconds after changing the seat weight before proceeding to allow the system to stabilize; only press scan
tool buttons when directed to do so; and perform the Occupant Classification Module System Verification
Test to completion.
With the scan tool in OCM, select More Options, select System Tests, and select Occupant Classification Module
System Verification Test. Run the test by following the instructions displayed on the scan tool. When the test is
complete, wait two minutes, and then proceed as follows.
With the scan tool, read OCM DTCs.
Does the scan tool display any active DTCs?
Yes
>> Diagnose and repair the DTCs. Refer to the Table of Contents in this Section for a complete list of
symptoms.
No
>> Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.
PM
RESTRAINTS - ELECTRICAL DIAGNOSTICS
8O - 345
RESTRAINTS - SERVICE INFORMATION
TABLE OF CONTENTS
page
page
RESTRAINTS - SERVICE INFORMATION
AIRBAG SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . 353
RESTRAINTS - TORQUE SPECIFICATIONS . . 357
RESTRAINT SYSTEMS . . . . . . . . . . . . . . . . . . . . . 358
CHILD RESTRAINT ANCHOR
CLOCKSPRING
CLOCKSPRING CENTERING . . . . . . . . . . . . . . . 362
CURTAIN AIRBAG
DRIVER AIRBAG
DRIVER AIRBAG COVER
FRONT SEAT BELT AND RETRACTOR
FRONT SEAT BELT BUCKLE
FRONT SEAT BELT HEIGHT ADJUSTER
IMPACT SENSOR
KNEE BLOCKER AIRBAG
KNEE BLOCKER AIRBAG COVER
OCCUPANT CLASSIFICATION MODULE
OCCUPANT RESTRAINT CONTROLLER
PASSENGER AIRBAG
PASSENGER AIRBAG COVER
REAR CENTER SEAT BELT AND RETRACTOR
REAR SEAT BELT AND RETRACTOR
REAR SEAT BELT BUCKLE
CENTER/LEFT BUCKLE . . . . . . . . . . . . . . . . . . . . 405
RIGHT BUCKLE/CENTER SEAT BELT
ANCHOR LATCH . . . . . . . . . . . . . . . . . . . . . . . . . 405
CENTER/LEFT BUCKLE . . . . . . . . . . . . . . . . . . . . 405
RIGHT BUCKLE/CENTER SEAT BELT
ANCHOR LATCH . . . . . . . . . . . . . . . . . . . . . . . . . 406
SEAT BELT-TENSIONER
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
8O - 346
RESTRAINTS - SERVICE INFORMATION
PM
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
SENSOR-SEAT WEIGHT
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408
PM
RESTRAINTS - SERVICE INFORMATION
8O - 347
RESTRAINTS - SERVICE INFORMATION
DESCRIPTION
Available occupant restraints for this vehicle include both active and passive types. Active restraints are those which
require the vehicle occupants to take some action to employ, such as fastening a seat belt; while passive restraints
require no action by the vehicle occupants to be employed.
ACTIVE RESTRAINTS
The active restraints for this vehicle include:
•
Child Restraint Anchors - All vehicles are equipped with three, fixed-position, child seat upper tether anchors
for the rear seating. Two anchors are integral to the back of the left rear seat back panel, and one is integral
to the right rear seat back panel. Two lower anchors are also provided for each rear outboard seating position.
The lower anchors are integral to the rear seat back panel bracket on the rear floor panel and are accessed
from the front of the rear seat where the seat back meets the seat cushion.
•
Front Seat Belts - Both front seating positions are equipped with three-point seat belt systems employing
lower B-pillar mounted inertia latch-type emergency locking retractors, height-adjustable upper B-pillar mounted
turning loops, a traveling lower seat belt anchor secured to the outboard side of the seat frame, and a traveling
end-release seat belt buckle secured to the inboard side of the seat frame. Both front seat belt retractors
include an integral seat belt switch that detects whether the front seat belts have been fastened.
•
Rear Seat Belts - All three rear seating positions are equipped with three-point seat belt systems. The out-
board seating position belts employ lower C-pillar mounted inertia latch-type emergency locking retractors,
fixed position upper C-pillar mounted turning loops, self-cinching latch plates for compatibility with child seats,
and fixed lower seat belt anchors secured to the rear floor panel by fasteners shared with the rear seat back
panel bracket. The rear seat center seating position has a D-pillar inertia latch-type emergency locking retrac-
tor. The center retractor for this vehicle is unique in the fact that the lower anchor is unlatchable to enable the
folding flat of the rear seat backs. The rear seat center seating position belt lower anchors are secured to the
rear floor panel with the outboard seat belt buckles. All three rear seat belts have fixed end-release seat belt
buckles secured to the rear floor panel by fasteners shared with the rear seat back panel bracket.
PASSIVE RESTRAINTS
The passive restraints available for this vehicle include
the following:
8O - 348
RESTRAINTS - SERVICE INFORMATION
PM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст