Dodge Caliber. Manual — part 536
B231C-REAR WIPER MOTOR CONTROL CIRCUIT HIGH
For a complete wiring diagram Refer to Section 8W.
Possible Causes
REAR WIPER RELAY
INTEGRATED POWER MODULE
Diagnostic Test
1.
INTEGRATED POWER MODULE
Turn the ignition off.
Replace the Rear Wiper relay with a known good relay.
With the Scan Tool, clear all FCM DTC’s.
Turn the Rear Wipers ON then OFF.
With the Scan Tool, read the FCM DTC’s.
Does the Scan Tool read: B231C-REAR WIPER MOTOR CONTROL CIRCUIT HIGH?
Yes
>> Replace the Integrated Power Module in accordance with the service information.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/FRONT CONTROL MODULE - DIAGNOSIS AND TESTING)
No
>> Test complete.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/FRONT CONTROL MODULE - DIAGNOSIS AND TESTING)
PM
WIPERS/WASHERS - ELECTRICAL DIAGNOSTICS
8R - 15
B2324-HEADLAMP WASHER MOTOR CONTROL CIRCUIT HIGH
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
•
With the ignition on.
•
Set Condition:
•
When the FCM detects a short/HIGH condition.
Possible Causes
INTEGRATED POWER MODULE
Diagnostic Test
1.
HEADLAMP WASHER RELAY
Turn the ignition off.
Replace the Rear Wiper relay with a known good relay.
With the Scan Tool, clear all FCM DTC’s.
Turn the Rear Wipers ON then OFF.
With the Scan Tool, read the FCM DTC’s.
Does the Scan Tool read: B2324-REAR WIPER MOTOR CONTROL CIRCUIT HIGH?
Yes
>> Replace the Integrated Power Module in accordance with the service information.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/FRONT CONTROL MODULE - DIAGNOSIS AND TESTING)
No
>> Test complete.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/FRONT CONTROL MODULE - DIAGNOSIS AND TESTING)
8R - 16
WIPERS/WASHERS - ELECTRICAL DIAGNOSTICS
PM
B2325-HEADLAMP WASHER MOTOR CONTROL CIRCUIT OPEN
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
•
With the ignition on.
•
Set Condition:
•
When the FCM detects a short/HIGH condition.
Possible Causes
INTEGRATED POWER MODULE
Diagnostic Test
1.
INTEGRATED POWER MODULE
Turn the ignition off.
Replace the Wiper ON/OFF relay with a known good relay.
With the Scan Tool, clear all FCM DTC’s.
Turn the Wipers ON then OFF.
With the Scan Tool, read the Wiper DTC’s.
Does the Scan Tool read: B2325-WIPER ON/OFF CONTROL CIRCUIT HIGH?
Yes
>> Replace the Integrated Power Module in accordance with the service information.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/FRONT CONTROL MODULE - DIAGNOSIS AND TESTING)
No
>> Test complete.
Perform the BODY VERIFICATION TEST — VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/FRONT CONTROL MODULE - DIAGNOSIS AND TESTING)
PM
WIPERS/WASHERS - ELECTRICAL DIAGNOSTICS
8R - 17
WIPERS/WASHERS - SERVICE INFORMATION
TABLE OF CONTENTS
page
page
WIPERS/WASHERS - SERVICE INFORMATION
CHECK VALVE
FRONT WIPER MOTOR
REAR WIPER MOTOR
RIGHT MULTI-FUNCTION SWITCH
RIGHT MULTI-FUNCTION SWITCH . . . . . . . . . . . 37
WASHER NOZZLE
FRONT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
REAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
PUMP-WASHER-WINDSHIELD
WASHER RESERVOIR
WIPER ARM
WIPER BLADE
WIPER MODULE
8R - 18
WIPERS/WASHERS - SERVICE INFORMATION
PM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст