Dodge Caliber. Manual — part 383
3.
(P697) DRIVER DOOR LOCK SWITCH MUX CIRCUIT SHORT TO GROUND
Turn the ignition off.
Disconnect the Cluster C2 connector.
Measure the resistance between ground and the (P697) Driver Door
Lock Switch Mux circuit.
Is the resistance below 10,000.0 ohms?
Yes
>> Repair the (P697) Driver Door Lock Switch Mux circuit for a
short to ground.
Perform BODY VERIFICATION TEST - VER 1. (Refer to 8 -
ELECTRICAL/ELECTRONIC
CONTROL
MODULES
-
STANDARD PROCEDURE)
No
>> Replace the Instrument Cluster in accordance with service
information.
Perform BODY VERIFICATION TEST - VER 1. (Refer to 8 -
ELECTRICAL/ELECTRONIC
CONTROL
MODULES
-
STANDARD PROCEDURE)
PM
POWER LOCKS - ELECTRICAL DIAGNOSTICS
8N - 9
B1934–DRIVER DOOR LOCK/UNLOCK SWITCH CIRCUIT STUCK – CLUSTER
For a complete wiring diagram Refer to Section 8W.
8N - 10
POWER LOCKS - ELECTRICAL DIAGNOSTICS
PM
•
When Monitored:
Continuously
•
Set Condition:
When the Driver Door Lock Switch Mux circuit is between 0.8 and 3.5 volts for over 10 seconds.
Possible Causes
(P697) LEFT DOOR LOCK SWITCH MUX CIRCUIT PARTIAL SHORT TO GROUND
DOOR LOCK SWITCH SHORT TO GROUND
INSTRUMENT CLUSTER
Diagnostic Test
1.
TEST FOR INTERMITTENT CONDITION
With the scan tool, record and erase DTC’s
Operate the Driver Door Lock Switch in all positions several times.
Cycle the ignition from on to off.
Turn the ignition on.
With the scan tool, read DTC’s.
Does the scan tool display B1934–DRIVER DOOR LOCK/UNLOCK SWITCH CIRCUIT STUCK?
Yes
>> Go To 2
No
>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-
matic as a guide, inspect the wiring and connectors.
Perform BODY VERIFICATION TEST - VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE)
2.
DOOR LOCK SWITCH SHORTED
With the scan tool, erase DTC’s.
Disconnect the Driver Window/Door Lock Switch connector.
With the scan tool, read DTC’s.
Does the scan tool display B1934–DRIVER DOOR LOCK/UN-
LOCK SWITCH CIRCUIT STUCK?
No
>> Replace the Driver Window/Door Lock Switch.
Perform BODY VERIFICATION TEST - VER 1. (Refer to 8 -
ELECTRICAL/ELECTRONIC
CONTROL
MODULES
-
STANDARD PROCEDURE)
Yes
>> Go To 3
PM
POWER LOCKS - ELECTRICAL DIAGNOSTICS
8N - 11
3.
(P697) LEFT DOOR LOCK SWITCH MUX CIRCUIT PARTIAL SHORT TO GROUND
Turn the ignition off.
Disconnect the Cluster C2 connector.
Measure the resistance between ground and the (P697) Driver Door
Lock Switch Mux circuit.
Is the resistance below 1,000.0 ohms?
Yes
>> Repair the (P697) Left Door Lock Switch Mux circuit for a
short to ground.
Perform BODY VERIFICATION TEST - VER 1. (Refer to 8 -
ELECTRICAL/ELECTRONIC
CONTROL
MODULES
-
STANDARD PROCEDURE)
No
>> Replace the Instrument Cluster in accordance with service
information.
Perform BODY VERIFICATION TEST - VER 1. (Refer to 8 -
ELECTRICAL/ELECTRONIC
CONTROL
MODULES
-
STANDARD PROCEDURE)
8N - 12
POWER LOCKS - ELECTRICAL DIAGNOSTICS
PM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст