Dodge Caliber. Manual — part 501
PASSENGER AIRBAG COVER
REMOVAL
1. Open hood.
2. Disconnect and isolate the battery negative cable.
WARNING: Wait two minutes for the airbag system reserve capacitor to discharge before beginning any air-
bag system or component service. Failure to do so may result in accidental airbag deployment, personal
injury or death.
3. Remove the passenger airbag from the instrument panel (Refer to 8 - ELECTRICAL/RESTRAINTS/PASSENGER
AIRBAG - REMOVAL).
4. Unhook the trim cover from the passenger airbag by lifting the cover over the hook and latch retainers.
INSTALLATION
1. Install the passenger airbag trim cover over the hook and loop retainers on the passenger airbag.
2. Install the passenger airbag in the instrument panel (Refer to 8 - ELECTRICAL/RESTRAINTS/PASSENGER AIR-
BAG - INSTALLATION).
WARNING: Do not connect the battery negative cable (Refer to 8 - ELECTRICAL/RESTRAINTS - DIAGNOSIS
AND TESTING - AIRBAG SYSTEM). Personal injury or death may result if the system test is not performed
first.
PM
RESTRAINTS - SERVICE INFORMATION
8O - 401
REAR CENTER SEAT BELT AND RETRACTOR
REMOVAL
1. If center rear seatbelt (1) is latched to its anchor,
detach the Quick Connect Anchor by depressing
tab (2).
2. If seatbelt is unlatched from its anchor then remove
it from its stowage slot on the right quarter trim
panel.
3. Remove C-pillar upper trim panel (1) (Refer to 23 -
BODY/INTERIOR/C-PILLAR TRIM - REMOVAL).
4. Feed seatbelt webbing through C-pillar upper trim
panel.
5. Remove the rear center seatbelt upper turning loop
bolt (2).
6. Remove the rear center seatbelt retractor retaining
bolt (5) from the D-pillar (3).
7. Remove rear center seatbelt retractor (4) from the
vehicle.
8O - 402
RESTRAINTS - SERVICE INFORMATION
PM
INSTALLATION
1. Position rear center seatbelt retractor into hollow in
the D-pillar (3).
2. Install the rear center seatbelt retractor retaining
bolt (5). Tighten bolt to 40 N·m (29.5 ft. lbs.).
3. Feed seatbelt webbing through upper C-pillar trim
panel.
4. Install the upper C-pillar trim panel (Refer to 23 -
BODY/INTERIOR/UPPER
C-PILLAR
TRIM
-
INSTALLATION).
5. If replacing the seatbelt into the latch stowage,
place into slot and push down.
6. If latching seatbelt (1) to anchor (2), attach Quick
Connect Anchor (2).
PM
RESTRAINTS - SERVICE INFORMATION
8O - 403
REAR SEAT BELT AND RETRACTOR
REMOVAL
1. Remove the upper C-pillar trim (6) (Refer to 23 -
BODY/INTERIOR/UPPER
C-PILLAR
TRIM
-
INSTALLATION).
2. Remove the rear quarter panel trim (Refer to 23 -
BODY/INTERIOR/REAR QUARTER PANEL TRIM -
INSTALLATION).
3. Remove the rear outer seatbelt anchor bolt (2).
4. Feed the seatbelt webbing through the upper C-pil-
lar trim panel (6).
5. Remove the upper seatbelt turning loop bolt (5).
6. Remove the rear outer seatbelt retractor retaining
bolt (3).
7. Remove the rear outer seatbelt retractor (4) from
the C-pillar (1).
INSTALLATION
1. Position the rear outer seatbelt retractor (4) into the
C-pillar (1).
2. Install the rear outer seatbelt retractor retaining bolt
(3). Tighten bolt to 40 N·m (29.5 ft. lbs.).
3. Install the upper seatbelt turning loop bolt (5).
Tighten bolt to 40 N·m (29.5 ft. lbs.).
4. Feed the seatbelt webbing through the upper C-pil-
lar trim panel (6).
5. Install the rear outer seatbelt anchor bolt (2).
Tighten bolt to 40 N·m (29.5 ft. lbs.).
6. Install the rear quarter panel trim (Refer to 23 -
BODY/INTERIOR/REAR QUARTER PANEL TRIM -
INSTALLATION).
7. Install upper C-pillar trim (6) (Refer to 23 - BODY/
INTERIOR/UPPER C-PILLAR TRIM - INSTALLA-
TION).
8O - 404
RESTRAINTS - SERVICE INFORMATION
PM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст