Dodge Caliber. Manual — part 396
POWER FOLDAWAY MIRROR SWITCH - RHD
DIAGNOSIS AND TESTING - POWER FOLDAWAY MIRROR SWITCH - RHD
The following test is designed to be used only on vehi-
cles equipped with power foldaway side view mirrors.
1. Remove power mirror switch from mounting posi-
tion (Refer to 8 - ELECTRICAL/POWER MIR-
RORS/POWER FOLDAWAY MIRROR SWITCH -
REMOVAL).
2. Using an ohmmeter, test for continuity between the
terminals of the switch as shown in the tables
below.
NOTE: When testing using the chart below be certain to read the chart correctly. Example - When testing
left mirror “DOWN
↓
”, pins 1, 9, 10 will show continuity to each other but not with 3, 4, 5.
3. If test results are not obtained as shown in the tables below, replace the switch.
EXTENDED MIRROR SWITCH CIRCUIT TEST
NOTE: Mirror position switch must be in the “extended” position to use chart below.
WOBBLE PLATE POSITION
LEFT MIRROR SELECTED
RIGHT MIRROR SELECTED
CONTINUITY BETWEEN PINS
CONTINUITY BETWEEN PINS
DOWN
1, 9, 10
6, 9, 10
3, 4, 5
3, 4, 5
UP
1, 4, 5
6, 4, 5
3, 9, 10
3, 9, 10
RIGHT
2, 9, 10
7, 9, 10
3, 4, 5
3, 4, 5
LEFT
2, 4, 5
7, 4, 5
3, 9, 10
3, 9, 10
RETRACTED MIRROR SWITCH CIRCUIT TEST
NOTE: Mirror position switch must be in the “retracted” position to use chart below.
PM
POWER MIRRORS
8N - 61
WOBBLE PLATE POSITION
LEFT MIRROR SELECTED
RIGHT MIRROR SELECTED
CONTINUITY BETWEEN PINS
CONTINUITY BETWEEN PINS
DOWN
1, 3, 4, 9
3, 4, 6, 9
UP
1, 3, 4, 9
3, 4, 6, 9
RIGHT
2, 3, 4, 9
3, 4, 7, 9
LEFT
2, 3, 4, 9
3, 4, 7, 9
REMOVAL
1. Disconnect and isolate the battery negative cable.
2. Remove the front door bolster. (Refer to 23 -
BODY/DOOR - FRONT/DOOR - REMOVAL).
3. Disconnect the electrical harness connectors.
4. With the bolster on the bench, gently pry in on the
tabs of the mirror switch and push through the front
of the cover and remove.
INSTALLATION
1. Place the mirror switch in bolster opening and
firmly snap into place.
2. Connect the electrical harness connectors.
3. Install the front door bolster. (Refer to 23 - BODY/
DOOR - FRONT/DOOR - INSTALLATION)
4. Connect the battery negative cable.
8N - 62
POWER MIRRORS
PM
POWER TOP - SUNROOF - SERVICE INFORMATION
TABLE OF CONTENTS
page
page
POWER TOP - SUNROOF - SERVICE
SUNROOF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
MOTOR/MODULE - SUNROOF
MOTOR/MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
POWER SUNROOF TIMING . . . . . . . . . . . . . . . . . 68
SWITCH-SUNROOF
SUNROOF SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . 71
PM
POWER TOP - SUNROOF - SERVICE INFORMATION
8N - 63
POWER TOP - SUNROOF - SERVICE INFORMATION
DESCRIPTION
WARNING: Keep fingers and other body parts out of sunroof opening at all times.
The power sunroof system allows the sunroof to be opened, closed or placed in the vent position electrically by
actuating a switch located in the headliner on the courtesy/reading lamp assembly. The sunroof system receives
battery feed through a 25 amp fuse in the Totally Integrated Power Module (TIPM). The sunroof system power is
EXPLODED VIEW
8N - 64
POWER TOP - SUNROOF - SERVICE INFORMATION
PM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст