Dodge 1500 (Gas) (2006 year). Manual — part 30
Cavity Cartridge
Fuse
Mini
Fuse
Description
38
20 Amp
Yellow
Power Outlet IP
39
10 Amp
Red
Sunroof/Seatbelt Ten-
sioner
40
20 Amp
Yellow
Cigar Lighter
41
25 Amp
Natural
Spare
42
30 Amp
Pink
Diesel PCM (Diesel
Only)
1. Disconnect the battery negative (-) cable before remov-
ing the cover.
2. Use specified fuses only.
3. Always properly reinstall the cover.
VEHICLE STORAGE
If you are storing your vehicle for more than 21 days, we
recommend that you take the following steps to mini-
mize the drain on your vehicle’s battery:
• Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse
located in the Integrated Power Module, located in the
engine compartment. The I.O.D. cavity includes a
snap-in retainer that allows the fuse to be discon-
nected, without removing it from the fuse block.
• The electronic shift transfer case should be placed in
the 4HI mode and kept in this position to minimize the
battery drain.
• As an alternative to the above steps you may, discon-
nect the negative cables from both batteries.
NOTE:
When reinstalling the IOD fuse, the gages in the
Instrument Cluster will do a full sweep, when the
ignition key is cycled to RUN. This is a normal condition.
MAINTAINING YOUR VEHICLE
469
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
REPLACEMENT LIGHT BULBS
LIGHT BULBS — Inside
Bulb No.
Overhead Console Lights . . . . . . . . . . . . . . . TS 212-2
Dome Light. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7679
All of the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved.
LIGHT BULBS — Outside
Bulb No.
Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3057
Center High Mounted Stop Lamp . . . . . . . . . . . . . 912
Fog Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 9006LL
Headlamp (Halogen) . . . . . . . . . . . . . . . . . . . . . H13
Side Marker Bulb . . . . . . . . . . . . . . . . . . . . . . . W5W
Park & Turn Signal . . . . . . . . . . . . . . . . . . . 3157NAK
Rear License Plate Lamp . . . . . . . . . . . . . . . . . . . 168
Rear Cargo Light. . . . . . . . . . . . . . . . . . . . . . . . . 912
Tail & Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3057
Cab Clearance Lights . . . . . . . . . . . . . . . . . . . . . . 168
Dual Rear Wheel Sidemarker Light . . . . . . . . . . . . 168
Dual Rear Wheel Tailgate ID Lights (3) . . . . . . . . . 168
BULB REPLACEMENT
Headlight (Halogen)/Front Park and Turn Lights
CAUTION!
This is a halogen bulb. Avoid touching the glass
with your fingers. Reduced bulb life will result.
470
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
1. Open the hood
2. Remove the two (2) bolts from the front of the head-
light housing.
3. Remove the plug from the inner fender well and
remove the nut through the access hole.
Front Headlight Housing Bolts
Inner Fender Plug
MAINTAINING YOUR VEHICLE
471
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
4. Pull the housing out from the fender to allow room to
disconnect the electrical connectors.
NOTE:
For easier removal, pull the headlight assembly
straight forward, applying the greatest amount of force to
the outer edge of the headlight assembly.
Rear Headlight Housing Nut Access
Headlight Removal
472
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
5. Unlock and pull connector straight from the base of
the headlight halogen bulb.
6. Twist connector on turn signal/park light bulb
1
⁄
4
turn
and remove connector and bulb from housing.
7. Remove housing from vehicle with headlight halogen
bulb in housing.
8. Twist the headlight halogen bulb
1
⁄
4
turn and remove
headlight bulb from the housing.
9. Replace headlight or turn signal bulb. Do not touch
the headlight halogen bulb.
10. Reverse procedure for installation of bulbs and hous-
ing.
Bulb Removal
MAINTAINING YOUR VEHICLE
473
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Tail, Stop, Turn and Backup Lights
1. Remove the two (2) screws that pass through the bed
sheetmetal.
2. Pull the housing straight out from the body, with a
quick motion, to separate the housing from the body. If
not pulled straight, locators may be damaged.
474
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
3. Push the red lock slide in on the connector and remove
the housing from the vehicle.
4. Remove the four (4) screws from the bulb strip in the
housing.
5. Pull the appropriate bulb straight from the bulb strip.
• Top Bulb: Park/Turn/Hazard
• Center Bulb: Stop/Park/Sidemarker
• Bottom Bulb: Backup Lights
6. Reverse procedure for installation of bulbs and hous-
ing.
MAINTAINING YOUR VEHICLE
475
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
7. While holding the taillight firmly in place, fasten the
top screw first.
Center High-Mounted Stoplight With Cargo Light
1. Remove the two (2) screws holding the housing/lens
to the body as shown.
2. Separate the connector holding the housing and wir-
ing harness to the body.
3. Turn desired bulb socket
1
⁄
4
turn and remove socket
and bulb from housing.
4. Pull desired bulb straight from the socket.
476
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
• Outside Bulbs: Cargo Lamps
• Inside Bulb: Center High Mount Stop Lamp
5. Reverse procedure for installation of bulbs and hous-
ing.
Cab Top Clearance Lights — If Equipped
1. Remove the two screws from the top of the light.
MAINTAINING YOUR VEHICLE
477
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2. Rotate the socket
1
⁄
4
turn and pull it from the light
assembly.
3. Pull the bulb straight from it’s socket and replace.
478
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Tailgate ID Lights (Dual Rear Wheels) — If
Equipped
1. Remove the two screws and housing and access the
bulb sockets from the rear.
2. Turn socket
1
⁄
4
turn counterclockwise to access the
bulb.
MAINTAINING YOUR VEHICLE
479
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
3. Pull bulb straight out from socket.
4. Reverse procedure for installation of bulbs and hous-
ing.
Rear Light Bar ID Marker (Dual Rear Wheel) – If
Equipped
1. Loosen the two screws and the housing to gain access
to the bulb sockets.
2. Turn the socket 1/4 turn counterclockwise to access
the bulb.
480
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
3. Pull the bulb straight out from the socket.
4. Reverse procedure for installation of bulbs and hous-
ing.
Side Marker Lights (Dual Rear Wheels)
1. Push rearward on the side marker light assembly.
2. Pull the entire assembly from the fender.
3. Turn socket
1
⁄
4
turn counterclockwise and remove from
assembly to access the bulb.
4. Pull bulb straight out from socket.
5. Reverse procedure for installation of bulbs and hous-
ing.
MAINTAINING YOUR VEHICLE
481
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Fog Lights
1. Reach under the vehicle, unlock and twist connector
counterclockwise
1
⁄
4
turn and remove connector and bulb
from housing.
2. Pull bulb straight from the connector.
3. Reverse procedure for installation of bulbs and hous-
ing.
482
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
FLUIDS AND CAPACITIES
U.S.
Metric
Fuel
3.7L/4.7L, 87 Octane
5.7L, 89 Octane
1500 Shortbed Models
26 gal.
98L
1500 Longbed Models
35 gal.
132L
1500 Shortbed Models
34 gal.
128L
2500 Shortbed Models
34 gal.
128L
2500 Longbed Models
35 gal.
132L
3500 Shortbed Models
34 gal.
128L
3500 Longbed Models
35 gal.
132L
MAINTAINING YOUR VEHICLE
483
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
U.S.
Metric
Engine Oil (with filter)
3.7L Engine V-6, SAE 5W-30, API Certified
5.0 qts.
4.7L
4.7L Engine V-8, SAE 5W-30, API Certified
6.0 qts.
5.7L
5.7L Engine V-8, SAE 5W-20, API Certified
7.0 qts.
6.6L
Cooling System
3.7L (Mopar
威 Antifreeze/Coolant 5 Year/100,000 Mile
Formula)
17 qts.
16L
4.7L (Mopar
威 Antifreeze/Coolant 5 Year/100,000 Mile
Formula)
17 qts.
16L
5.7L (Mopar
威 Antifreeze/Coolant 5 Year/100,000 Mile
Formula)
18.7 qts.
17.7L
484
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст