Dodge Durango (DN). Manual — part 281
(5) Remove the steering column opening cover
from the instrument panel. Refer to Steering Col-
umn Opening Cover in the Removal and Installa-
tion section of this group for the procedures.
(6) Disengage the loop end of the gear selector
indicator cable from the lever on the left side of the
steering column (Fig. 9).
(7) Squeeze the sides of the plastic adjuster and
bracket unit to disengage the tabs that secure it to
the sides of the steering column window.
(8) Remove the gear selector indicator mechanism
and cable unit from the instrument panel.
INSTALLATION
(1) Position the gear selector indicator mechanism
and cable unit to the instrument panel.
(2) Squeeze the sides of the plastic adjuster and
bracket unit and engage the tabs that secure it with
the sides of the steering column window.
(3) Engage the loop end of the gear selector indi-
cator cable onto the lever on the left side of the steer-
ing column (Fig. 9).
(4) Position the gear selector indicator mechanism
onto the back of the instrument cluster housing.
(5) Install and tighten the two screws that secure
the gear selector indicator mechanism to the back of
the instrument cluster housing. Tighten the screws
to 2.2 N·m (20 in. lbs.).
(6) Install the instrument cluster onto the instru-
ment panel. Refer to Instrument Cluster in the
Removal and Installation section of this group for the
procedures.
(7) Check the gear selector indicator for proper cal-
ibration. If adjustment is needed, refer to Steering
Column in the Removal and Installation section of
Group 19 - Steering for the gear selector indicator
cable (PRNDL) adjustment procedure.
(8) Install the steering column opening cover onto
the instrument panel. Refer to Steering Column
Opening Cover in the Removal and Installation sec-
tion of this group for the procedures.
(9) Reconnect the battery negative cable.
PARK BRAKE RELEASE HANDLE
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS,
REFER
TO
GROUP
8M
-
PASSIVE
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
STEERING
WHEEL,
STEERING
COLUMN,
OR
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
SERVICE. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Reach under the driver side outboard end of
the instrument panel to access and unsnap the plas-
tic retainer clip that secures the park brake release
linkage rod to the lever on the back side of the park
brake release handle.
(3) Disengage the park brake release linkage rod
end from the lever on the back of the park brake
release handle.
(4) Using a trim stick or another suitable wide
flat-bladed tool, gently pry one of the park brake
handle hinge tabs away from its pivot pin on the
instrument panel (Fig. 10).
(5) While prying the park brake release handle
hinge tab with one hand, use the other hand to pull
the handle firmly down and away from the pivot pin.
(6) Remove the park brake release handle from the
instrument panel.
INSTALLATION
(1) Position the park brake release handle to the
instrument panel.
(2) Engage one of the park brake release handle
hinge tabs with one of the pivot pins on the instru-
ment panel.
(3) Align the second park brake release handle
hinge tab hinge over the second pivot pin on the
instrument panel.
(4) Press firmly on the park brake release handle
over the second hinge tab until it snaps over the sec-
ond pivot pin on the instrument panel.
Fig. 9 Gear Selector Indicator Cable Remove/Install
1 – STEERING COLUMN
2 – CABLE
3 – LOOP END
4 – LEVER
5 – ADJUSTER AND BRACKET
8E - 18
INSTRUMENT PANEL SYSTEMS
DN
REMOVAL AND INSTALLATION (Continued)
(5) Reach under the driver side outboard end of
the instrument panel to access and engage the park
brake release linkage rod end from the lever on the
back of the park brake release handle.
(6) Snap the plastic retainer clip that secures the
park brake release linkage rod to the lever on the
back side of the park brake release handle over the
linkage rod.
(7) Reconnect the battery negative cable.
INSTRUMENT PANEL LOWER
REINFORCEMENT
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS,
REFER
TO
GROUP
8M
-
PASSIVE
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
STEERING
WHEEL,
STEERING
COLUMN,
OR
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
SERVICE. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the steering column opening cover
from the instrument panel. Refer to Steering Col-
umn Opening Cover in the Removal and Installa-
tion section of this group for the procedures.
(3) Remove the two screws that secure the inside
hood latch release handle to the instrument panel
lower reinforcement and lower the release handle to
the floor.
(4) Depress the latch tabs that secure the 16-way
data link wire harness connector to the instrument
panel lower reinforcement, and push the connector
out of its mounting hole.
(5) Remove the four screws that secure the lower
reinforcement to the instrument panel (Fig. 11).
(6) Remove the lower reinforcement from the
instrument panel.
INSTALLATION
(1) Position the lower reinforcement onto the
instrument panel.
(2) Install and tighten the four screws that secure
the lower reinforcement to the instrument panel.
Tighten the screws to 2.2 N·m (20 in. lbs.).
(3) Install the 16-way data link wire harness con-
nector into the mounting hole on the instrument
panel lower reinforcement.
(4) Position the inside hood latch release handle to
the instrument panel lower reinforcement.
(5) Install and tighten the two screws that secure
the inside hood latch release handle to the instru-
ment panel lower reinforcement. Tighten the screws
to 2.8 N·m (25 in. lbs.).
(6) Install the steering column opening cover onto
the instrument panel. Refer to Steering Column
Opening Cover in the Removal and Installation sec-
tion of this group for the procedures.
(7) Reconnect the battery negative cable.
Fig. 10 Park Brake Release Handle Remove/Install
1 – INSERT BETWEEN HINGE TAB AND PIVOT PIN
2 – TRIM STICK
3 – PARK BRAKE RELEASE HANDLE
4 – INSTRUMENT PANEL
Fig. 11 Instrument Panel Lower Reinforcement
Remove/Install
1 – REINFORCEMENT
2 – SCREW
3 – INSTRUMENT PANEL
DN
INSTRUMENT PANEL SYSTEMS
8E - 19
REMOVAL AND INSTALLATION (Continued)
INSTRUMENT PANEL CENTER SUPPORT
BRACKET
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS,
REFER
TO
GROUP
8M
-
PASSIVE
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
STEERING
WHEEL,
STEERING
COLUMN,
OR
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
SERVICE. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Pull the floor carpet back from the front of the
floor panel transmission tunnel far enough to access
the center support bracket mounting screws.
(3) Remove the two screws that secure the center
support bracket to the instrument panel.
(4) Remove the two screws on the left, and one
screw on the right that secure the instrument panel
center support bracket to the Airbag Control Module
(ACM) bracket on the floor panel transmission tunnel
(Fig. 12).
(5) Remove the center support bracket from the
instrument panel.
INSTALLATION
(1) Position the center support bracket to the ACM
bracket on the floor panel transmission tunnel.
(2) Install and tighten the two screws on the left,
and one screw on the right that secure the instru-
ment panel center support bracket to the Airbag Con-
trol Module (ACM) bracket on the floor panel
transmission tunnel. Tighten the screws to 11.8 N·m
(105 in. lbs.).
(3) Align the screw holes in the instrument panel
to the mounting holes in the center support bracket.
(4) Install and tighten the two screws that secure
the center support bracket to the instrument panel.
Tighten the screws to 11.8 N·m (105 in. lbs.).
(5) Reposition the floor carpet on the front of the
floor panel transmission tunnel to conceal the instru-
ment panel center support bracket.
(6) Reconnect the battery negative cable.
INSTRUMENT PANEL ASH RECEIVER
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS,
REFER
TO
GROUP
8M
-
PASSIVE
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
STEERING
WHEEL,
STEERING
COLUMN,
OR
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
SERVICE. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Open the instrument panel ash receiver.
(3) Depress the spring retainer in the center of the
open ash receiver to release it, then lift the ash
receiver slightly and pull it straight out from the
pivot pins in the instrument panel lower bezel.
(4) Remove the two screws that secure the ash
receiver flame shield to the instrument panel lower
bezel (Fig. 13).
(5) Pull the ash receiver flame shield out from the
instrument panel far enough to disengage the two
retaining tabs on the top of the shield from the
mounting holes in the instrument panel lower bezel.
(6) Lower the flame shield from the instrument
panel lower bezel far enough to access the ash
receiver lamp and hood.
(7) Squeeze the ash receiver lamp and hood
bracket to disengage the unit from the mounting hole
in the flame shield.
(8) Remove the ash receiver flame shield from the
instrument panel lower bezel.
Fig. 12 Instrument Panel Center Support Bracket
Remove/Install
1 – CENTER SUPPORT BRACKET
2 – SCREW
3 – AIRBAG CONTROL MODULE BRACKET
8E - 20
INSTRUMENT PANEL SYSTEMS
DN
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Position the ash receiver flame shield to the
instrument panel lower bezel.
(2) Squeeze the ash receiver lamp and hood
bracket and engage the unit to the mounting hole in
the flame shield.
(3) Insert the two retaining tabs on the top of the
ash receiver flame shield into the mounting holes in
the instrument panel lower bezel, then push the
shield forward to engage the tabs with the bezel.
(4) Install and tighten the two screws that secure
the ash receiver flame shield to the instrument panel
lower bezel. Tighten the screws to 2.2 N·m (20 in.
lbs.).
(5) Align the pivot receptacles on each side of the
ash receiver with the pivot pins in the instrument
panel lower bezel.
(6) Push the ash receiver forward onto the pivot
pins in the instrument panel lower bezel until the
spring retainer in the center of the open ash receiver
snaps into place.
(7) Reconnect the battery negative cable.
INSTRUMENT PANEL LOWER BEZEL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS,
REFER
TO
GROUP
8M
-
PASSIVE
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
STEERING
WHEEL,
STEERING
COLUMN,
OR
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
SERVICE. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the cluster bezel from the instrument
panel. Refer to Cluster Bezel in the Removal and
Installation section of this group for the procedures.
(3) Open the glove box.
(4) Remove the two screws that secure the lower
edge of the lower bezel to the instrument panel (Fig.
14).
(5) Remove the four screws that secure the upper
edge of the lower bezel to the instrument panel.
(6) Pull the lower bezel away from the instrument
panel far enough to access the instrument panel wire
harness connectors.
(7) Disconnect the instrument panel wire harness
connectors from the ash receiver lamp, the cigar
lighter, the power outlet and the rear window switch
module.
(8) Remove the lower bezel from the instrument
panel.
INSTALLATION
(1) Position the lower bezel to the instrument
panel.
(2) Reconnect the instrument panel wire harness
connectors to the ash receiver lamp, the cigar lighter,
the power outlet and the rear window switch module.
(3) Align the mounting holes in the lower bezel
with the screw holes in the instrument panel.
(4) Install and tighten the four screws that secure
the upper edge of the lower bezel to the instrument
panel. Tighten the screws to 2.2 N·m (20 in. lbs.).
Fig. 13 Instrument Panel Ash Receiver Remove/
Install
1 – INSTRUMENT PANEL LOWER BEZEL
2 – ASH RECEIVER
3 – SCREW
4 – FLAME SHIELD
Fig. 14 Instrument Panel Lower Bezel Remove/
Install
1 – INSTRUMENT PANEL LOWER BEZEL
2 – SCREW
DN
INSTRUMENT PANEL SYSTEMS
8E - 21
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст