Dodge Durango (DN). Manual — part 288
POWER AMPLIFIER
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS,
REFER
TO
GROUP
8M
-
PASSIVE
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
STEERING
WHEEL,
STEERING
COLUMN,
OR
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
SERVICE. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the trim cover from the right cowl side
inner panel. Refer to Cowl Trim Cover in the
Removal and Installation section of Group 23 - Body
for the procedures.
(3) Disconnect the two instrument panel wire har-
ness connectors from the connector receptacles on the
bottom of the power amplifier (Fig. 10).
(4) Remove the two screws that secure the power
amplifier to the right cowl side inner panel (Fig. 11).
(5) To disengage the upper hook bracket of the
power amplifier from the upper hinge access hole in
the right cowl side inner panel:
(a) Lift the power amplifier upwards about 5
centimeters (2 inches).
(b) Tilt the top of the power amplifier toward the
instrument panel.
(c) Keep the top of the power amplifier tilted
toward the instrument panel while lowering the
unit from between the right cowl side inner panel
and the end of the heater-A/C housing.
(6) Remove the power amplifier from the right
cowl side inner panel.
INSTALLATION
(1) Position the power amplifier to the right cowl
side inner panel.
(2) To engage the upper hook bracket of the power
amplifier in the upper hinge access hole in the right
cowl side inner panel:
(a) Tilt the top of the power amplifier toward the
instrument panel.
(b) Keep the top of the power amplifier tilted
toward the instrument panel while lifting the unit
up between the right cowl side inner panel and the
end of the heater-A/C housing.
Fig. 10 Power Amplifier Connections Remove/Install
1 – HEATER-A/C HOUSING
2 – ANTENNA COAXIAL CABLE
3 – FENDER
4 – HINGE PILLAR
5 – AMPLIFIER
6 – WIRE HARNESS
Fig. 11 Power Amplifier Remove/Install
1 – UPPER HINGE ACCESS HOLE
2 – COWL SIDE INNER PANEL
3 – HOOK
4 – SCREW
5 – AMPLIFIER
8F - 14
AUDIO SYSTEMS
DN
REMOVAL AND INSTALLATION (Continued)
(c) When the lower power amplifier mounting
brackets are about 5 centimeters (2 inches) above
the mounting holes for the lower brackets in the
right cowl side inner panel, tilt the top of the
power amplifier toward the right cowl side inner
panel.
(d) Lower the power amplifier until the upper
hook bracket is engaged in the upper hinge access
hole in the right cowl side inner panel. Tighten the
screws to 2 N·m (17 in. lbs.).
(3) Install and tighten the two screws that secure
the power amplifier to the right cowl side inner
panel.
(4) Reconnect the two instrument panel wire har-
ness connectors to the connector receptacles on the
bottom of the power amplifier.
(5) Install the trim cover onto the right cowl side
inner panel. Refer to Cowl Trim Cover in the
Removal and Installation section of Group 23 - Body
for the procedures.
(6) Reconnect the battery negative cable.
ANTENNA
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS,
REFER
TO
GROUP
8M
-
PASSIVE
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
STEERING
WHEEL,
STEERING
COLUMN,
OR
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
SERVICE. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
REMOVAL
ANTENNA BODY AND CABLE
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the trim cover from the right cowl side
inner panel. Refer to Cowl Trim Cover in the
Removal and Installation section of Group 23 - Body
for the procedures.
(3) Reach under the instrument panel below the
glove box to access and disconnect the antenna coax-
ial cable connector (Fig. 12). Disconnect the connector
by pulling it apart while twisting the metal connector
halves. Do not pull on the cable.
(4) Disengage the antenna coaxial cable from the
retainer clips on the lower instrument panel rein-
forcement and the heater-A/C housing.
(5) Disengage the antenna coaxial cable retainers
at the right cowl side inner panel and inside the
right front fender.
(6) Unscrew the antenna mast from the antenna
body (Fig. 13).
Fig. 12 Antenna Coaxial Cable Routing
1 – CLIP
2 – ANTENNA BODY AND CABLE
3 – RIGHT FRONT FENDER
4 – RETAINER
5 – AMPLIFIER
6 – TO RADIO
7 – COAXIAL CABLE
8 – INSTRUMENT PANEL
9 – CONNECTOR
10 – CLIP
11 – TO ANTENNA
12 – GLOVE BOX BIN
13 – ANTENNA BODY AND CABLE
14 – TO ANTENNA
15 – HEATER-A/C HOUSING
16 – TO RADIO
DN
AUDIO SYSTEMS
8F - 15
REMOVAL AND INSTALLATION (Continued)
(7) Remove the antenna cap nut using an antenna
nut wrench (Special Tool C-4816) (Fig. 14).
(8) Remove the antenna adapter from the top of
the fender.
(9) Lower the antenna body through the mounting
hole in the top of the fender.
(10) Pull the antenna body and cable out through
the opening between the right cowl side outer panel
and the fender through the front door opening (Fig.
15).
(11) Disengage the antenna coaxial cable grommet
from the hole in the right cowl side outer panel.
(12) Pull the antenna coaxial cable out of the pas-
senger compartment through the hole in the right
cowl side outer panel.
(13) Remove the antenna body and cable from the
vehicle.
INSTRUMENT PANEL ANTENNA CABLE
(1) Disconnect and isolate the battery negative
cable.
(2) Reach under the instrument panel below the
glove box to access and disconnect the antenna coax-
ial cable connector (Fig. 12). Disconnect the connector
by pulling it apart while twisting the metal connector
halves. Do not pull on the cable.
(3) Securely tie a suitable length of cord or twine
to the instrument panel half of the antenna coaxial
cable connector. This cord will be used to pull or
“fish” the cable back into position during installation.
(4) Disengage the instrument panel antenna cable
from the retainer clip on the lower instrument panel
reinforcement inboard of the glove box opening.
(5) Roll down the glove box from the instrument
panel. Refer to Glove Box in the Removal and
Installation section of Group 8E - Instrument Panel
Systems for the procedures.
Fig. 13 Antenna Mast Remove/Install - Typical
1 – ANTENNA MAST
2 – ADAPTER
3 – CAP NUT
Fig. 14 Antenna Cap Nut and Adapter Remove/
Install - Typical
1 – CAP NUT
2 – ANTENNA ADAPTER
3 – TOOL
Fig. 15 Antenna Mounting
1 – ADAPTER
2 – MAST
3 – NUT
4 – ANTENNA BODY AND CABLE
5 – RIGHT FRONT FENDER
6 – RETAINER
7 – GROMMET
8F - 16
AUDIO SYSTEMS
DN
REMOVAL AND INSTALLATION (Continued)
(6) Reach through the glove box opening to access
and disengage the retainer that secures the antenna
cable to the instrument panel structural support on
the inboard side of the glove box opening.
(7) Remove the radio receiver from the instrument
panel. Refer to Radio Receiver in the Removal and
Installation section of this group for the procedures.
(8) Pull the antenna cable out through the radio
receiver opening in the instrument panel.
(9) Untie the cord or twine from the instrument
panel antenna cable connector, leaving the cord or
twine in place of the cable in the instrument panel.
(10) Remove the antenna cable from the instru-
ment panel.
INSTALLATION
ANTENNA BODY AND CABLE
(1) Position the antenna body and cable in the
opening between the right cowl side outer panel and
the fender through the front door opening.
(2) Push the antenna coaxial cable into the passen-
ger compartment through the hole in the right cowl
side outer panel.
(3) Engage the antenna coaxial cable grommet in
the hole in the right cowl side outer panel.
(4) Position the antenna body through the mount-
ing hole in the top of the fender.
(5) Install the adapter over the antenna body from
the top of the fender.
(6) Install and tighten the antenna cap nut using
an
antenna
nut
wrench
(Special
Tool
C-4816).
Tighten the antenna cap nut to 8 N·m (70 in. lbs.).
(7) Install and tighten the antenna mast onto the
antenna body. Tighten the mast to 3.3 N·m (30 in.
lbs.).
(8) Engage the antenna coaxial cable retainers at
the right cowl side inner panel and inside the right
front fender.
(9) Engage the antenna coaxial cable in the
retainer clips on the lower instrument panel rein-
forcement and the heater-A/C housing.
(10) Reach under the instrument panel below the
glove box to reconnect the antenna coaxial cable con-
nector.
(11) Install the trim cover onto the right cowl side
inner panel. Refer to Cowl Trim Cover in the
Removal and Installation section of Group 23 - Body
for the procedures.
(12) Reconnect the battery negative cable.
INSTRUMENT PANEL ANTENNA CABLE
(1) Tie the end of the cord or twine that was used
during instrument panel antenna cable removal
securely to the connector on the end of the antenna
coaxial cable being installed into the instrument
panel. This cord will be used to pull or “fish” the
cable back into position.
(2) Using the cord or twine, pull the antenna cable
through the radio receiver opening from under the
instrument panel.
(3) Install the radio receiver onto the instrument
panel. Refer to Radio Receiver in the Removal and
Installation section of this group for the procedures.
(4) Reach through the glove box opening to access
and engage the retainer that secures the antenna
cable to the instrument panel structural support on
the inboard side of the glove box opening.
(5) Install the glove box onto the instrument panel.
Refer to Glove Box in the Removal and Installation
section of Group 8E - Instrument Panel Systems for
the procedures.
(6) Engage the instrument panel antenna cable to
the retainer clip on the lower instrument panel rein-
forcement inboard of the glove box opening.
(7) Untie the cord or twine from the instrument
panel half of the antenna coaxial cable connector.
(8) Reach under the instrument panel below the
glove box to access and reconnect the antenna coaxial
cable connector.
(9) Reconnect the battery negative cable.
RADIO NOISE SUPPRESSION COMPONENTS
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS,
REFER
TO
GROUP
8M
-
PASSIVE
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
STEERING
WHEEL,
STEERING
COLUMN,
OR
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
SERVICE. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
REMOVAL
ENGINE-TO-BODY GROUND STRAPS
(1) Remove the nut and washer that secures the
left engine-to-body ground strap eyelet terminal to
the weld stud on the left side of the lower plenum
panel (Fig. 16).
(2) Remove the nut and washer that secures the
right engine-to-body ground strap eyelet terminal to
the inboard weld stud on the right side of the lower
plenum panel (Fig. 16).
(3) Remove the screw that secures the left engine-
to-body ground strap eyelet terminal to the rear of
the left cylinder head (Fig. 17) or (Fig. 18).
(4) Remove the screw that secures the right
engine-to-body ground strap eyelet terminal to the
rear of the right cylinder head (Fig. 17) or (Fig. 18).
DN
AUDIO SYSTEMS
8F - 17
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст