Dodge Neon / Neon SRT-4. Manual — part 341
(25) Remove rear sun gear and #7 needle bearing
(Fig. 33).
NOTE: The number 7 needle bearing has three anti-
reversal tabs and is common with the number five
and number two position. The orientation should
allow the bearing to seat flat against the rear sun
gear (Fig. 34). A small amount of petrolatum can be
used to hold the bearing to the rear sun gear.
(26) Setup tool 5058 as shown in (Fig. 35). Com-
press 2/4 clutch return spring (just enough to remove
snap ring) and remove snap ring.
NOTE: Verify that Tool 5058 is centered properly
over the 2/4 clutch retainer before compressing. If
necessary, fasten the 5058 bar to the bellhousing
flange with any combination of locking pliers and
bolts to center the tool properly.
NOTE: The 2/4 Clutch Piston has bonded seals
which are not individually serviceable. Seal replace-
ment requires replacement of the piston assembly.
(27) Remove 2/4 clutch retainer (Fig. 36).
(28) Remove 2/4 clutch return spring (Fig. 37).
Fig. 33 Remove Rear Sun Gear
1 - #7 NEEDLE BEARING
2 - REAR SUN GEAR
Fig. 34 Number 7 Bearing
1 - #7 NEEDLE BEARING
2 - REAR SUN GEAR
Fig. 35 Remove 2/4 Clutch Retainer Snap Ring
1 - TOOL 5058
2 - SCREWDRIVER
3 - SNAP RING
4 - 2/4 CLUTCH RETAINER
Fig. 36 2/4 Clutch Retainer
1 - 2/4 CLUTCH RETAINER
2 - 2/4 CLUTCH RETURN SPRING
21 - 148
40TE AUTOMATIC TRANSAXLE
PL/SRT-4
40TE AUTOMATIC TRANSAXLE (Continued)
(29) Remove 2/4 clutch pack (Fig. 38). Tag 2/4
clutch pack for reassembly identification.
(30) Remove tapered snap ring (Fig. 39).
(31) Remove low/reverse reaction plate (Fig. 40).
(32) Remove one low/reverse clutch disc (Fig. 41).
Fig. 37 Remove 2/4 Clutch Return Spring
1 - 2/4 CLUTCH RETURN SPRING
Fig. 38 Remove 2/4 Clutch Pack
1 - CLUTCH DISC
2 - CLUTCH PLATE
Fig. 39 Remove Tapered Snap Ring
1 - LOW/REVERSE CLUTCH REACTION PLATE
2 - SCREWDRIVER
3 - LOW/REVERSE TAPERED SNAP RING (TAPERED SIDE UP)
4 - OIL PAN FACE
5 - LONG TAB
Fig. 40 Remove Low/Reverse Reaction Plate
1 - LOW/REVERSE REACTION PLATE (FLAT SIDE UP)
PL/SRT-4
40TE AUTOMATIC TRANSAXLE
21 - 149
40TE AUTOMATIC TRANSAXLE (Continued)
(33) Remove low/reverse reaction plate snap ring
(Fig. 42).
(34) Remove low/reverse clutch pack (Fig. 43).
(35) Remove transfer gear cover-to-case bolts (Fig.
44).
(36) Remove transfer gear cover (Fig. 45).
Fig. 41 Remove One Disc
1 - ONE DISC FROM LOW/REVERSE CLUTCH
Fig. 42 Remove Low/Reverse Reaction Plate Snap
Ring
1 - SCREWDRIVER
2 - LOW/REVERSE REACTION PLATE FLAT SNAP RING
3 - DO NOT SCRATCH CLUTCH PLATE
Fig. 43 Remove Low/Reverse Clutch
1 - CLUTCH PLATE
2 - CLUTCH DISC
Fig. 44 Remove Rear Cover Bolts
1 - REAR COVER BOLTS
2 - REAR COVER
3 - USE SEALANT ON BOLTS
21 - 150
40TE AUTOMATIC TRANSAXLE
PL/SRT-4
40TE AUTOMATIC TRANSAXLE (Continued)
(37) Using Tool 6259, remove transfer shaft gear-
to-shaft nut and coned washer (Fig. 46) (Fig. 47).
(38) Using tool L-4407A, remove transfer shaft
gear (Fig. 48).
(39) Remove transfer gear shim (select) (Fig. 49).
Fig. 45 Remove Rear Cover
1 - REAR COVER
2 - 1/8 INCH BEAD OF MOPAR
T
ATF RTV (MS-GF41) AS SHOWN
Fig. 46 Remove Transfer Shaft Gear Nut
1 - TRANSFER SHAFT GEAR
2 - OUTPUT GEAR
3 - SPECIAL TOOL 6259
Fig. 47 Transfer Shaft Gear Nut and Coned Washer
1 - TRANSFER SHAFT
2 - LOCK WASHER
3 - NUT
Fig. 48 Remove Transfer Shaft Gear
1 - SPECIAL TOOL L4407-6
2 - TRANSFER SHAFT GEAR
3 - SPECIAL TOOL L4407A
PL/SRT-4
40TE AUTOMATIC TRANSAXLE
21 - 151
40TE AUTOMATIC TRANSAXLE (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст