Dodge Neon / Neon SRT-4. Manual — part 326
Puller Set, 5048
Disconnect Tool, 6638A
Remover, 6786
Remover/Installer, 6891
Alignment Pins, 8470
Installer, 8471
Race Remover, 8472
Bearing Installer, 8473
21 - 88
T850 MANUAL TRANSAXLE
PL/SRT-4
T850 MANUAL TRANSAXLE (Continued)
Remover/Installer, 8474
Installer, 8475
Installer, 8476
Wrench, 8478
Stake Tool, 8479
Installer, 8481
Bearing Installer, 8482
Fixture, 8483
PL/SRT-4
T850 MANUAL TRANSAXLE
21 - 89
T850 MANUAL TRANSAXLE (Continued)
AXLE SEALS
REMOVAL
(1) Raise vehicle on hoist.
(2) Remove one or both front halfshaft assemblies.
(Refer to 3 - DIFFERENTIAL & DRIVELINE/HALF
SHAFT - REMOVAL)
(3) Using a suitable screwdriver, remove one or
both axle seals (Fig. 92).
INSTALLATION
(1) Using driver handle C-4171 and installer 8476,
install axle seals into position (Fig. 94) (Fig. 93).
(2) Install one or both front halfshaft assemblies.
(Refer to 3 - DIFFERENTIAL & DRIVELINE/HALF
SHAFT - INSTALLATION)
(3) Check transaxle fluid level and adjust if neces-
sary. (Refer to 21 - TRANSMISSION/TRANSAXLE/
MANUAL/FLUID - STANDARD PROCEDURE)
(4) Lower vehicle.
Fixture, 8487
Lifting Bar, 8489
Thrust Buttons, 8491
Wrench, 8827
Fig. 92 Axle Seal Removal (Extension Housing Side
Shown)
1 - SCREWDRIVER
2 - AXLE SEAL
3 - EXTENSION HOUSING
21 - 90
T850 MANUAL TRANSAXLE
PL/SRT-4
T850 MANUAL TRANSAXLE (Continued)
BACK-UP LAMP SWITCH
REMOVAL
(1) Raise vehicle on hoist.
(2) Disconnect back-up lamp switch connector.
(3) Remove back-up lamp switch (Fig. 95).
INSTALLATION
(1) Install back-up lamp switch (Fig. 95) and
torque to 23 N·m (17 ft. lbs.).
(2) Connect back-up lamp switch connector.
(3) Lower vehicle.
DIFFERENTIAL
DESCRIPTION
NOTE: The Quaife ATB Differential is serviced only
as a complete assembly. The only serviceable com-
ponents are the ring gear and tapered roller bear-
ings. No other component replacement will be
possible.
The Quaife Automatic Torque Biasing (ATB) Lim-
ited Slip Differential (Fig. 96) (Fig. 97) is a perfor-
mance-oriented unit which is designed to provide
traction to both drive wheels during all driving con-
ditions.
A billet differential gear body houses two helical
sun gears which are splined to the front axles. Each
sun gear is in mesh with its own set of (6) helical
planetary pinion gears which provide differential
action during turning and cornering maneuvers. A
center pack consisting of belleville spring washers
sandwiched between a pair of spring housings apply
pressure to the the sun gears. The unit is supported
by tapered roller bearings.
Fig. 93 Axle Seal Installation (Extension Housing
Side)
1 - EXTENSION HOUSING
2 - SEAL
3 - INSTALLER 8476
4 - DRIVER HANDLE C-4171
Fig. 94 Axle Seal Installation
1 - SEAL
2 - INSTALLER 8476
3 - DRIVER HANDLE C-4171
Fig. 95 Back-Up Lamp Switch
1 - BACK-UP LAMP SWITCH
PL/SRT-4
T850 MANUAL TRANSAXLE
21 - 91
AXLE SEALS (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст