Dodge Neon / Neon SRT-4. Manual — part 248
![](/vehicles/wlang/sta/knessild/qut.png)
(8) Rotate the crankshaft CLOCKWISE two com-
plete revolutions manually for seating of the belt,
until the crankshaft is repositioned at the TDC posi-
tion. Verify that the camshaft and crankshaft timing
marks are in proper position (Fig. 156).
(9) Check if the spring tang is within the tolerance
window (Fig. 155). If the spring tang is within the
tolerance window, the installation process is complete
and nothing further is required. If the spring tang is
not within the tolerance window, repeat Steps 6
through 8.
(10) Install front timing belt cover (Refer to 9 -
ENGINE/VALVE TIMING/TIMING BELT COVER(S)
- INSTALLATION).
(11) Install spark plugs (Refer to 8 - ELECTRI-
CAL/IGNITION CONTROL/SPARK PLUG - INSTAL-
LATION).
(12) Perform
camshaft
and
crankshaft
timing
relearn procedure as follows:
• Connect the DRB IIIt scan tool to the data link
(diagnostic) connector. This connector is located in
the passenger compartment; at the lower edge of
instrument panel near the steering column.
• Turn the ignition switch on.
• Access “Engine” diagnostics.
• Select “Miscellaneous” option.
• Select “ReLearn Cam Crank” option and follow
directions on DRBIII
t screen.
Fig. 154 Timing Belt Tension Adjustment
1 - ALIGN SETTING NOTCH WITH SPRING TANG
2 - TOP PLATE
3 - 6mm ALLEN WRENCH
4 - LOCK NUT
5 - SETTING NOTCH
6 - SPRING TANG
Fig. 155 Timing Belt Tension Verification
1 - SPRING TANG
2 - TOLERANCE WINDOW
Fig. 156 Crankshaft and Camshaft Timing
1 - CAMSHAFT TIMING MARKS
2 - CRANKSHAFT AT TDC
9 - 86
ENGINE 2.0L SOHC
PL/SRT-4
TIMING BELT AND SPROCKETS (Continued)
![](/vehicles/wlang/sta/knessild/orapousus.png)
TIMING BELT TENSIONER
ASSEMBLY
REMOVAL
WITH MECHANICAL TENSIONER
(1) Remove timing belt (Refer to 9 - ENGINE/
VALVE TIMING/TIMING BELT AND SPROCKETS -
REMOVAL).
(2) Remove bolts attaching the timing belt ten-
sioner assembly to engine.
(3) Remove timing belt tensioner assembly (Fig.
157).
INSTALLATION
WITH MECHANICAL TENSIONER
(1) Position timing belt tensioner assembly to the
engine. To ensure proper alignment of tensioner to
engine block, temporarily install the engine mount
bracket bolts into the upper holes of the timing belt
tensioner. Install timing belt tensioner lower mount-
ing bolts. Tighten lower mounting bolts to 31 N·m
(23 ft. lbs.). Remove temporarily installed engine
mount bracket bolts.
(2) Install timing belt (Refer to 9 - ENGINE/
VALVE TIMING/TIMING BELT AND SPROCKETS -
INSTALLATION).
Fig. 157 Timing Belt Tensioner Assembly
1 - SPRING TANG
2 - LOCK NUT
3 - TOP PLATE
4 - PULLEY
5 - SETTING NOTCH
6 - BRACKET
PL/SRT-4
ENGINE 2.0L SOHC
9 - 87
![](/vehicles/wlang/sta/knessild/myekng.png)
ENGINE 2.4L DOHC TURBO
TABLE OF CONTENTS
page
page
ENGINE 2.4L DOHC TURBO
. . . . . . . . . . . . . . . . . . . . . . . . . 90
ENGINE DIAGNOSIS - INTRODUCTION
ENGINE DIAGNOSIS - PERFORMANCE
LEAKAGE TEST . . . . . . . . . . . . . . . . . . . . . . 95
TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
THREADS . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
FORM-IN-PLACE GASKETS AND SEALERS
ENGINE GASKET SURFACE PREPARATION
ENGINE CORE AND OIL GALLERY PLUGS
MEASURING BEARING CLEARANCE USING
PLASTIGAGE . . . . . . . . . . . . . . . . . . . . . . . . 99
INSTALLATION - ENGINE ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . 104
. . . . . . . . . . . . . . . . . . . . . . . . . . . 108
. . . . . . . . . . . . . . . . . . . . . . . . 109
AIR CLEANER ELEMENT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
. . . . . . . . . . . . . . . . . . . . . . . . 113
AIR CLEANER HOUSING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
. . . . . . . . . . . . . . . . . . . . . . . . 114
CYLINDER HEAD
. . . . . . . . . . . . . . . . . . . . . . . . 114
. . . . . . . . . . . . . . . . . . . . . . . . . . . 116
. . . . . . . . . . . . . . . . . . . . . . . . . . 116
CAMSHAFT OIL SEAL(S)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
. . . . . . . . . . . . . . . . . . . . . . . . 119
CAMSHAFT(S)
. . . . . . . . . . . . . . . . . . . . . . . . 119
. . . . . . . . . . . . . . . . . . . . . . . . . . 119
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
. . . . . . . . . . . . . . . . . . . . . . . . . . . 120
. . . . . . . . . . . . . . . . . . . . . . . . . 120
. . . . . . . . . . . . . . . . . . . . . . . . 121
CYLINDER HEAD COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
. . . . . . . . . . . . . . . . . . . . . . . . 122
HYDRAULIC LASH ADJUSTERS
DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . . . 123
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
. . . . . . . . . . . . . . . . . . . . . . . . 124
INTAKE/EXHAUST VALVES & SEATS
. . . . . . . . . . . . . . . . . . . . . . . . 124
. . . . . . . . . . . . . . . . . . . . . . . . . . 124
. . . . . . . . . . . . . . . . . . . . . . . . . . . 124
ROCKER ARMS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
. . . . . . . . . . . . . . . . . . . . . . . . . 124
. . . . . . . . . . . . . . . . . . . . . . . . 124
VALVE SPRINGS & SEALS
. . . . . . . . . . . . . . . . . 125
. . . . . . . . . . . . . . . . 125
. . . . . . . . . . . . . . . . . . . . . . . . . 126
. . . . . . . . . . . . . . . . . 126
. . . . . . . . . . . . . . . . 126
ENGINE BLOCK
. . . . . . . . . . . . . . . . . . . . . . . . 126
. . . . . . . . . . . . . . . . . . . . . . . . . . . 127
. . . . . . . . . . . . . . . . . . . . . . . . . 128
CRANKSHAFT
. . . . . . . . . . . . . . . 128
. . . . . . . . . . . . . . . . . . . . . . . . . 129
CRANKSHAFT OIL SEAL - FRONT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
. . . . . . . . . . . . . . . . . . . . . . . . 132
CRANKSHAFT OIL SEAL - REAR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
. . . . . . . . . . . . . . . . . . . . . . . . 134
PISTON & CONNECTING ROD
. . . . . . . . . . . . . . . . . . . . . . . . 134
STANDARD PROCEDURE - PISTON TO
9 - 88
ENGINE 2.4L DOHC TURBO
PL/SRT-4
![](/vehicles/wlang/sta/knessild/ghea.png)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
. . . . . . . . . . . . . . . . . . . . . . . . 137
CONNECTING ROD BEARINGS
PISTON RINGS
. . . . . . . . . . . . . . . 138
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
. . . . . . . . . . . . . . . . . . . . . . . . 139
STRUCTURAL COLLAR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
. . . . . . . . . . . . . . . . . . . . . . . . 140
VIBRATION DAMPER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
. . . . . . . . . . . . . . . . . . . . . . . . 141
ENGINE MOUNTING
. . . . . . . . . . . . . . . . . . . . . . . . 141
LEFT MOUNT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
. . . . . . . . . . . . . . . . . . . . . . . . 142
RIGHT MOUNT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
. . . . . . . . . . . . . . . . . . . . . . . . 142
TORQUE STRUT
. . . . . . . . . . . . . . 143
. . . . . . . . . . . . . . 143
. . . . . . . . . . . . . . 143
. . . . . . . . . . . . . . 143
ENGINE TORQUE STRUT ADJUSTMENT
LUBRICATION
. . . . . . . . . . . . . . . . . . . . . . . . 145
. . . . . . . . . . . . . . . . . . . . . . . . . . 145
OIL
OIL FILTER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
. . . . . . . . . . . . . . . . . . . . . . . . 147
OIL FILTER ADAPTER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
. . . . . . . . . . . . . . . . . . . . . . . . 147
OIL PAN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
. . . . . . . . . . . . . . . . . . . . . . . . 148
OIL PRESSURE SENSOR/SWITCH
. . . . . . . . . . . . . . . . . . . . . . . . 149
. . . . . . . . . . . . . . . . . . . . . . . . . . 149
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
. . . . . . . . . . . . . . . . . . . . . . . . 149
OIL PUMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
. . . . . . . . . . . . . . . . . . . . . . . . 150
. . . . . . . . . . . . . . . . . . . . . . . . . . . 150
. . . . . . . . . . . . . . . . . . . . . . . . . 151
. . . . . . . . . . . . . . . . . . . . . . . . . . . 151
. . . . . . . . . . . . . . . . . . . . . . . . 151
OIL JET
. . . . . . . . . . . . . . . . . . . . . . . . 152
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
. . . . . . . . . . . . . . . . . . . . . . . . 153
OIL COOLER & LINES
. . . . . . . . . . . . . . . . . . . . . . . . 153
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
. . . . . . . . . . . . . . . . . . . . . . . . 154
INTAKE MANIFOLD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
. . . . . . . . . . . . . . . . . . . . . . . . . . . 156
. . . . . . . . . . . . . . . . . . . . . . . . . 156
. . . . . . . . . . . . . . . . . . . . . . . . 156
EXHAUST MANIFOLD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
. . . . . . . . . . . . . . . . . . . . . . . . 156
TIMING BELT COVER(S)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
. . . . . . . . . . . . . . . . . . . . . . . . 159
TIMING BELT AND SPROCKETS
. . . . . . . . . . . . . . . . . . . . . . . . 159
. . . . . . . . . . . . . . . . . . . . . . . . 161
TIMING BELT TENSIONER & PULLEY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
. . . . . . . . . . . . . . . . . . . . . . . . 163
BALANCE SHAFTS AND CARRIER ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . 165
. . . . . . . . . . . . . . . . . . . . . . . . . . 165
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
. . . . . . . . . . . . . . . . . . . . . . . . 167
PL/SRT-4
ENGINE 2.4L DOHC TURBO
9 - 89
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст