Dodge Neon / Neon SRT-4. Manual — part 464
![](/vehicles/wlang/sta/knessild/yeroule.png)
TEST
ACTION
APPLICABILITY
4
NOTE: Ensure the battery is fully charged.
With the DRBIII
t, record and erase all DTCs from all modules.
All active codes must be resolved before diagnosing any stored codes.
Maintain a safe distance from all airbags while performing the following steps.
With the DRBIII
t monitor active codes as you work through the system.
NOTE: If equipped with Passenger Airbag On-Off switch, read the DTC’s in
all switch positions.
Wiggle the wiring harness and connectors of the appropriate airbag system and
rotate the steering wheel from stop to stop.
NOTE: Check connectors - Clean and repair as necessary.
You have just attempted to simulate the condition that initially set the trouble code
message.
The following additional checks may assist you in identifying a possible intermittent
problem:
- Visually inspect related wire harness connectors. Look for broken, bent, pushed out,
spread, corroded, or contaminated terminals.
- Visually inspect the related harnesses. Look for chafed, pierced, pinched or partially
broken wire.
- Refer to Wiring Diagrams and Technical Service Bulletins that may apply.
Did the DTC become active ?
All
Yes
→ Select appropriate symptom from Symptom List.
No
→ No problem found at this time. Erase all codes before returning
vehicle to customer.
78
AIRBAG
SEAT SQUIB SHORT TO BATTERY —
Continued
![](/vehicles/wlang/sta/knessild/inato.png)
Symptom:
SEAT SQUIB SHORT TO GROUND
When Monitored and Set Condition:
SEAT SQUIB SHORT TO GROUND
When Monitored:
When the ignition is on, the SIACM monitors the resistance of the Seat
Squib circuits.
Set Condition:
When the SIACM detects a short to ground on the Seat Squib circuits.
POSSIBLE CAUSES
SEAT AIRBAG SHORT TO GROUND
SEAT SQUIB LINE 1 OR LINE 2 SHORTED TO GROUND
SIACM, SEAT SQUIB SHORT TO GROUND
STORED CODE OR INTERMITTENT CONDITION
ACTIVE CODE PRESENT
TEST
ACTION
APPLICABILITY
1
Ensure the battery is fully charged.
Turn the ignition on.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ONE:
All
LEFT SIACM - ACTIVE DTC
LEFT SIACM - STORED DTC
RIGHT SIACM - ACTIVE DTC
RIGHT SI ACM - STORED DTC
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
79
AIRBAG
![](/vehicles/wlang/sta/knessild/batruro.png)
TEST
ACTION
APPLICABILITY
2
WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED SEAT BACK PAD-
DED SIDE DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL
INTO THE AIR IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN
SERIOUS OR FATAL INJURY.
Disconnect the Seat Airbag connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Seat Airbag connector.
WARNING: TURN IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t, read SIACM active DTC’s.
Does the DRBIII
t display SEAT SQUIB SHORT TO GROUND?
All
Yes
→ Go To 3
No
→ Replace the Seat Airbag in accordance with Service Instructions.
Perform AIRBAG VERIFICATION TEST - VER 1.
3
WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED SEAT BACK PAD-
DED SIDE DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL
INTO THE AIR IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN
SERIOUS OR FATAL INJURY.
Disconnect the Airbag Load Tool Jumper.
Disconnect the Side Impact Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool SIACM adaptor to the SIACM connector.
Measure the resistance of the Seat Squib Line 1 and Line 2 circuits between the
Curtain Squib connector and ground.
Is the resistance below 10K ohms on either circuit?
All
Yes
→ Repair Seat Squib Line 1 or Line 2 shorted to ground.
Perform AIRBAG VERIFICATION TEST - VER 1.
No
→ Replace the Side Impact Airbag Control Module in accordance
with Service Instructions. WARNING: IF THE SIDE IMPACT
AIRBAG CONTROL MODULE IS DROPPED AT ANY TIME, IT
MUST BE REPLACED.
Perform AIRBAG VERIFICATION TEST - VER 1.
80
AIRBAG
SEAT SQUIB SHORT TO GROUND —
Continued
![](/vehicles/wlang/sta/knessild/plllilayoupl.png)
TEST
ACTION
APPLICABILITY
4
NOTE: Ensure the battery is fully charged.
With the DRBIII
t, record and erase all DTCs from all modules.
All active codes must be resolved before diagnosing any stored codes.
Maintain a safe distance from all airbags while performing the following steps.
With the DRBIII
t monitor active codes as you work through the system.
NOTE: If equipped with Passenger Airbag On-Off switch, read the DTC’s in
all switch positions.
Wiggle the wiring harness and connectors of the appropriate airbag system and
rotate the steering wheel from stop to stop.
NOTE: Check connectors - Clean and repair as necessary.
You have just attempted to simulate the condition that initially set the trouble code
message.
The following additional checks may assist you in identifying a possible intermittent
problem:
- Visually inspect related wire harness connectors. Look for broken, bent, pushed out,
spread, corroded, or contaminated terminals.
- Visually inspect the related harnesses. Look for chafed, pierced, pinched or partially
broken wire.
- Refer to Wiring Diagrams and Technical Service Bulletins that may apply.
Did the DTC become active ?
All
Yes
→ Select appropriate symptom from Symptom List.
No
→ No problem found at this time. Erase all codes before returning
vehicle to customer.
81
AIRBAG
SEAT SQUIB SHORT TO GROUND —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст