Dodge Neon / Neon SRT-4. Manual — part 225
Fig. 54 BODY (RIGHT REAR) - RHD
Fig. 55 DOOR (PASSENGER) - RHD
8W - 91 - 62
8W-91 CONNECTOR/GROUND/SPLICE LOCATION
PL/SRT-4
CONNECTOR/GROUND/SPLICE LOCATION (Continued)
Fig. 56 DOOR (DRIVER) - RHD
Fig. 57 DOOR (REAR) - RHD
PL/SRT-4
8W-91 CONNECTOR/GROUND/SPLICE LOCATION
8W - 91 - 63
CONNECTOR/GROUND/SPLICE LOCATION (Continued)
Fig. 58 DECKLID - RHD
8W - 91 - 64
8W-91 CONNECTOR/GROUND/SPLICE LOCATION
PL/SRT-4
CONNECTOR/GROUND/SPLICE LOCATION (Continued)
8W-97 POWER DISTRIBUTION
TABLE OF CONTENTS
page
page
CIGAR LIGHTER OUTLET
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . . . 1
FUSE BLOCK
. . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . . . 2
POWER DISTRIBUTION CENTER
. . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . . . 3
CIGAR LIGHTER OUTLET
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Look inside and note position of the retaining
bosses (Fig. 1).
(3) Using external snap ring pliers with 90 degree
tips. Insert pliers with tips against bosses and
squeeze forcing bosses out of base.
(4) Pull out the base through mounting ring by
gently rocking pliers. A tool can be made to do the
same (Fig. 2).
(5) Disconnect the base wires.
(6) Set base aside and remove base mount ring.
INSTALLATION
(1) Position mount ring to the instrument panel
and feed the wires through ring. Index the cap and
the mount ring with the index tab at 9 o’clock to the
key in the instrument panel. Install the ring.
(2) Connect wires to base. Orient base alignment
rib at 11 o’clock to mate the groove in mount ring at
the same location
(3) Push base into the bezel till it locks.
(4) Install cigar lighter cap and check operation of
element.
(5) Connect the battery negative cable.
FUSE BLOCK
DESCRIPTION
An electrical Fuse Block is located in the left end
of the instrument panel. It serves to simplify and
centralize numerous electrical components, as well as
Fig. 1 CIGAR LIGHTER/POWER OUTLET BASE
REMOVAL
1 - RETAINING BOSSES ENGAGE PLIERS HERE
2 - PARTIALLY REMOVED
3 - EXTERNAL SNAP-RING PLIERS
4 - PULL BASE OUT THROUGH MOUNTING RING
Fig. 2 CIGAR LIGHTER/POWER OUTLET BASE
REMOVAL
1 - 2.5 mm (3/32 inches)
2 - WELD
3 - 100 mm (4 inches)
4 - 22.25 TO 22.45 mm (7/8 TO 57/64 inches)
PL/SRT-4
8W-97 POWER DISTRIBUTION
8W - 97 - 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст