Dodge Neon / Neon SRT-4. Manual — part 309
(c) Verify throttle body duct is fully seated to
intake manifold and tighten clamp to 5 N·m (40 in.
lbs.) torque.
(d) Connect the Throttle Position Sensor (TPS)
and Idle Air Control (IAC) connectors.
(e) Connect proportional purge solenoid (PPS)
and crankcase vent hose from throttle body.
(22) Connect the battery cables.
(23) Road test vehicle and inspect for leaks.
SPECIFICATIONS
Bolts that have thread sealer or torque lock
patches should not be reused. Always install new
bolts in these applications.
TORQUE SPECIFICATIONS
DESCRIPTION
N·m
Ft. Lbs.
In. Lbs.
Back-up Lamp Switch
24
18
—
Crossover Cable Adj. Screw
8
—
70
Drain Plug
14
—
120
Differential Ring Gear Bolts
81
60
—
Dust Shield to Transaxle
12
—
105
End Plate Cover Bolts
29
21
—
Front Engine Mount to Trans
108
80
—
Front Mount Through Bolt
61
45
—
Front Mount to Engine Bolt
54
40
—
Lateral Bending Strut to Engine
54
40
—
Lateral Bending Strut to Trans.
54
40
—
Left Mount Through Bolt
108
80
—
Left Mount to Transaxle
54
40
—
Output Bearing Race Ret. Strap
11
—
96
Reverse Fork Bracket
11
—
96
Reverse Idler Shaft Bolt
29
19
—
Shift Cable Bracket to Transaxle
28
—
250
Transaxle Case Bolts
29
21
—
Transaxle to Engine Bolt
95
70
—
Vehicle Speed Sensor
7
—
60
Vertical Bending Strut to Engine
108
80
—
Vertical Bending Strut to Trans.
108
80
—
NV T350 (A-578) MANUAL TRANSAXLE FLUID FILL
TRANSAXLE
METRIC MEASURE
U.S. MEASURE
NV T350
2.4-2.7 Liters
2.5-2.8 Quarts
21 - 20
T350 MANUAL TRANSAXLE
PL/SRT-4
T350 MANUAL TRANSAXLE (Continued)
SPECIAL TOOLS
Adapter Blocks C-293-45
Puller Press C-293–PA
Dial Indicator C-3339
Sleeve C-3717
Slide Hammer C-3752
Universal Handle C-4171
Bearing Installer C-4628
Seal Remover C-4680
Seal Installer C-4992
Torque Tool C-4995
PL/SRT-4
T350 MANUAL TRANSAXLE
21 - 21
T350 MANUAL TRANSAXLE (Continued)
Adapter C-4996
Installer L-4410
Special Jaw Set L-4518
Bearing Splitter 1130
Driver 6342
Seal Installer 6709
Bearing Remover 6768
Bench Fixture 6785
Remover 6786
Remover 6787
21 - 22
T350 MANUAL TRANSAXLE
PL/SRT-4
T350 MANUAL TRANSAXLE (Continued)
AXLE SEAL
REMOVAL
(1) Remove axle shaft. (Refer to 3 - DIFFEREN-
TIAL & DRIVELINE/HALF SHAFT - REMOVAL)
(2) Insert a flat–blade pry tool at outer edge of
axle shaft seal (Fig. 60).
(3) Tap on the pry tool with a small hammer and
remove axle shaft seal.
INSTALLATION
(1) Clean axle shaft seal bore of any excess seal-
ant.
(2) Align axle shaft seal with axle shaft seal bore.
(3) Install axle seal on Tool #6709 and C-4171 and
insert into axle shaft seal bore.
(4) Tap seal into position until seated against
transaxle case.
(5) Install axle shaft. (Refer to 3 - DIFFEREN-
TIAL & DRIVELINE/HALF SHAFT - INSTALLA-
TION)
(6) Check transaxle fluid level and adjust as nec-
essary.
BACK-UP LAMP SWITCH
REMOVAL
(1) Lift vehicle on hoist.
(2) From bottom side of vehicle, disconnect back-up
lamp switch connector (Fig. 61).
(3) Unscrew switch from transaxle.
INSTALLATION
(1) Install back-up lamp switch. Teflon tape or
equivalent must be used on switch threads. Tighten
switch to 24 N·m (18 ft. lbs.) torque.
CAUTION: Do not overtighten switch.
(2) Connect back-up lamp switch connector (Fig.
61).
(3) Lower vehicle.
(4) Verify back-up lamp operation.
Fig. 60 Axle Shaft Seal Removal
1 - AXLE SEAL
2 - PRY TOOL
Fig. 61 BACK-UP LAMP SWITCH
1 - CONNECTOR
2 - BACK UP LAMP SWITCH
PL/SRT-4
T350 MANUAL TRANSAXLE
21 - 23
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст