Dodge Dakota (R1). Manual — part 64
TEST
ACTION
APPLICABILITY
13
Turn the ignition off..
Disconnect the Central Timer Module C2 connector.
Turn the ignition on.
Measure the voltage of the Cylinder Lock Switch Mux circuit in the CTM C2
connector.
Is there any voltage present?
All
Yes
→
Repair the Cylinder Lock Switch Mux circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→
14
If there are no possible causes remaining, view repair.
All
Repair
Replace the Central Timer Module.
Perform BODY VERIFICATION TEST - VER 1.
253
POWER DOOR LOCKS/RKE
CYLINDER LOCK SWITCH FAILURE —
Continued
Symptom:
DRIVER DOOR LOCK SWITCH SHORT TO GROUND
When Monitored and Set Condition:
DRIVER DOOR LOCK SWITCH SHORT TO GROUND
When Monitored:
Continuously.
Set Condition:
If the CTM detects that the voltage on the Driver Door Switch Mux circuit
drops below 1.5 volts, this code will set.
POSSIBLE CAUSES
DRIVER DOOR SWITCH SHORT TO GROUND
CODE ACTIVE
DRIVER DOOR SWITCH MUX WIRE SHORT TO GROUND
CENTRAL TIMER MODULE - DRIVER DOOR LOCK SWITCH SHORT TO GROUND
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Operate the door locks several times.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display DRIVER DOOR LOCK SWITCH SHORT TO GROUND?
All
Yes
→
No
→
Problem is intermittent and not present at this time. Using the
wiring diagram/schematic as a guide, inspect the wiring and
connectors and repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
2
Disconnect the Driver Door Lock Switch
Disconnect the Central Timer Module C2 connector.
Measure the resistance between ground and the Driver Door Switch Mux circuit.
Is the resistance below 100.0 ohms?
All
Yes
→
Repair the Driver Door Switch Mux wire for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→
3
Reconnect the Driver Door Lock Switch
Disconnect the Central Timer Module C2 connector.
Measure the resistance between ground and the Driver Door Switch Mux circuit.
Is the resistance below 1000.0 ohms?
All
Yes
→
Replace the Driver Door Lock Switch.
Perform BODY VERIFICATION TEST - VER 1.
No
→
254
POWER DOOR LOCKS/RKE
TEST
ACTION
APPLICABILITY
4
If there are no possible causes remaining, view repair.
All
Repair
Replace the Central Timer Module.
Perform BODY VERIFICATION TEST - VER 1.
255
POWER DOOR LOCKS/RKE
DRIVER DOOR LOCK SWITCH SHORT TO GROUND —
Continued
Symptom:
PASSENGER DOOR LOCK SWITCH SHORT TO GROUND
When Monitored and Set Condition:
PASSENGER DOOR LOCK SWITCH SHORT TO GROUND
When Monitored:
Continuously.
Set Condition:
If the CTM detects that the voltage on the Passenger Door Switch Mux
circuit drops below 1.5 volts, this code will set.
POSSIBLE CAUSES
PASSENGER DOOR SWITCH SHORT TO GROUND
CODE ACTIVE
PASSENGER DOOR SWITCH MUX WIRE SHORT TO GROUND
CENTRAL TIMER MODULE - PASSENGER DOOR LOCK SWITCH SHORT TO GROUND
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Operate the door locks several times.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display PASS DOOR LOCK SWITCH SHORT TO GROUND?
All
Yes
→
No
→
Problem is intermittent and not present at this time. Using the
wiring diagram/schematic as a guide, inspect the wiring and
connectors and repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
2
Disconnect the Passenger Door Lock Switch
Disconnect the Central Timer Module C2 connector.
Measure the resistance between ground and the Passenger Door Switch Mux circuit.
Is the resistance below 100.0 ohms?
All
Yes
→
Repair the Passengerer Door Switch Mux wire for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→
3
Ensure the Passenger Door Lock Switch is connected before proceeding.
Disconnect the Central Timer Module C2 connector.
Measure the resistance between ground and the Passenger Door Switch Mux circuit.
Is the resistance below 1000.0 ohms?
All
Yes
→
Replace the Passenger Door Lock Switch.
Perform BODY VERIFICATION TEST - VER 1.
No
→
256
POWER DOOR LOCKS/RKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст