Dodge Dakota (R1). Manual — part 144
Symptom:
P1230-TIMING GOVERNING NEGATIVE GOVERNOR DEVIATION
When Monitored and Set Condition:
P1230-TIMING GOVERNING NEGATIVE GOVERNOR DEVIATION
When Monitored:
With the engine speed between 1000 and 4800 RPM.
Set Condition:
The ECM detects 3 degrees of excess timing retard for at least 10 seconds.
POSSIBLE CAUSES
CHECK FOR OTHER DTCS
ENGINE CONTROL MODULE
REPLACE THE FUEL INJECTION PUMP
INTERMITTENT CONDITION
FUEL INJECTION PUMP TIMING INCORRECT
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, erase ECM DTCs.
Turn the ignition off, wait 30 seconds, then attempt to start the engine.
With the DRB, read ECM DTCs.
Did this DTC reset?
All
Yes
→
No
→
2
NOTE: This DTC will set due to noise on the Needle Movement Sensor
circuit.
Turn the ignition on.
With the DRB, check for additional DTCs.
Are other DTCs present?
All
Yes
→
Refer to the Symptom List for diagnosis of the other DTCs before
continuing.
Perform ROAD TEST VERIFICATION - VER-2.
No
→
3
Check the Fuel Injection Pump timing using the Service Information.
Is the Fuel Injection Pump timed correctly?
All
Yes
→
No
→
Reset the Fuel Injection Pump timing in accordance with the
Service Information.
Perform ROAD TEST VERIFICATION - VER-2.
111
DRIVEABILITY - DIESEL
TEST
ACTION
APPLICABILITY
4
Replace the Fuel Injection Pump in accordance with the Service Information.
With the DRB, erase ECM DTCs.
Perform several drive cycles, turning the ignition off for at least 10 seconds between
each drive cycle.
Monitor the DRB for ECM DTCs.
Did this DTC reset?
All
Yes
→
Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.
No
→
The repair is complete.
Perform ROAD TEST VERIFICATION - VER-2.
5
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?
All
Yes
→
Repair as necessary
Perform ROAD TEST VERIFICATION - VER-2.
No
→
Test Complete.
112
DRIVEABILITY - DIESEL
P1230-TIMING GOVERNING NEGATIVE GOVERNOR DEVIATION —
Continued
Symptom:
P1230-TIMING GOVERNING POSITIVE GOVERNOR DEVIATION
When Monitored and Set Condition:
P1230-TIMING GOVERNING POSITIVE GOVERNOR DEVIATION
When Monitored:
With the engine speed between 1000 and 4800 RPM.
Set Condition:
The ECM detects 3 degrees of excess timing advance for at least 10
seconds.
POSSIBLE CAUSES
ENGINE CONTROL MODULE
REPLACE THE FUEL INJECTION PUMP
INTERMITTENT CONDITION
FUEL SYSTEM RESTRICTIONS
FUEL INJECTION PUMP TIMING INCORRECT
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, erase ECM DTCs.
Turn the ignition off, wait 30 seconds, then attempt to start the engine.
With the DRB, read ECM DTCs.
Did this DTC reset?
All
Yes
→
No
→
2
NOTE: This DTC will set due to low fuel volume to the Fuel Injection Pump.
Check the fuel system for restrictions.
Were any problems found?
All
Yes
→
Repair as necessary.
Perform ROAD TEST VERIFICATION - VER-2.
No
→
3
Check the Fuel Injection Pump timing using the Service Information.
Is the Fuel Injection Pump timed correctly?
All
Yes
→
No
→
Reset the Fuel Injection Pump timing in accordance with the
Service Information.
Perform ROAD TEST VERIFICATION - VER-2.
113
DRIVEABILITY - DIESEL
TEST
ACTION
APPLICABILITY
4
Replace the Fuel Injection Pump in accordance with the Service Information.
With the DRB, erase ECM DTCs.
Perform several drive cycles, turning the ignition off for at least 10 seconds between
each drive cycle.
Monitor the DRB for ECM DTCs.
Did this DTC reset?
All
Yes
→
Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.
No
→
The repair is complete.
Perform ROAD TEST VERIFICATION - VER-2.
5
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?
All
Yes
→
Repair as necessary
Perform ROAD TEST VERIFICATION - VER-2.
No
→
Test Complete.
114
DRIVEABILITY - DIESEL
P1230-TIMING GOVERNING POSITIVE GOVERNOR DEVIATION —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст