Dodge Dakota (R1). Manual — part 778
INSTALLATION
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
NOTE: Be certain that the rubber defroster grille-to-
windshield seal is in place on the forward edge of
the defroster grille before it is installed to the
instrument panel.
(1) Position the defroster grille onto the top of the
instrument panel (Fig. 9).
(2) Align the snap clips on the defroster grille with
the receptacles in the instrument panel base trim.
(3) Using hand pressure, press firmly on the
defroster grille over each of the snap clip locations
until each of the snap clips is fully engaged in its
receptacle.
(4) Reinstall the trim onto both A-pillars. (Refer to
23 - BODY/INTERIOR/A-PILLAR TRIM - INSTAL-
LATION).
(5) Reconnect the battery negative cable.
END CAP
REMOVAL - DRIVER SIDE
(1) Insert a finger into the pull cup formation
molded into the end cap and pull firmly and sharply
outward to disengage each of the snap clips that
secure the end cap from their receptacles in the
instrument panel base trim (Fig. 10)
(2) Remove the end cap from the end of the instru-
ment panel.
REMOVAL - PASSENGER SIDE
(1) Using a trim stick or another suitable wide
flat-bladed tool, gently pry around the perimeter of
the passenger side end cap to disengage each of the
snap clips from their receptacles in the instrument
panel base trim (Fig. 11).
(2) Remove the end cap from the end of the instru-
ment panel.
INSTALLATION
(1) Position the end cap to the outboard end of the
instrument panel.
(2) Align the snap clips on the end cap with the
receptacles in the instrument panel base trim (Fig.
10).
(3) Using hand pressure, press firmly on the end
cap over each of the snap clip locations until each of
the snap clips is fully engaged in its receptacle in the
instrument panel base trim.
Fig. 10 End Cap Remove/Install
1 - RECEPTACLES
2 - SNAP CLIPS
3 - END CAP
Fig. 11 End Cap Remove/Install - Typical
1 - RECEPTACLES
2 - SNAP CLIPS
3 - END CAP
23 - 100
INSTRUMENT PANEL SYSTEM
AN
DEFROSTER GRILLE (Continued)
GLOVE BOX
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the cluster bezel from the instrument
panel. (Refer to 23 - BODY/INSTRUMENT PANEL/
CLUSTER BEZEL - REMOVAL).
(3) Remove the lower bezel from the instrument
panel. (Refer to 23 - BODY/INSTRUMENT PANEL/
LOWER BEZEL - REMOVAL).
(4) Remove the screw that secures the inboard side
of the glove box module to the instrument panel
behind the lower bezel.
(5) Remove the passenger side end cap from the
instrument panel. (Refer to 23 - BODY/INSTRU-
MENT PANEL/END CAP - REMOVAL - PASSEN-
GER SIDE).
(6) Remove the screw that secures the outboard
end of the glove box module to the right end of the
instrument panel behind the passenger side end cap.
(7) Remove the four screws that secure the bottom
of the glove box module to the instrument panel (Fig.
12).
(8) Unlatch and open the glove box.
(9) Remove the latch striker from the upper glove
box opening reinforcement. (Refer to 23 - BODY/IN-
STRUMENT PANEL/GLOVE BOX LATCH STRIKER
- REMOVAL).
(10) Remove the two remaining screws that secure
the top of the glove box module to the upper glove
box opening reinforcement.
(11) If the vehicle is equipped with a glove box
lamp, pull the glove box module away from the
instrument panel far enough to access and disconnect
the instrument panel wire harness connector from
the glove box lamp and switch connector receptacle
(Fig. 13).
(12) Remove the glove box module from the instru-
ment panel.
DISASSEMBLY
The glove box latch and handle unit of the glove
box used in this vehicle is serviced individually. Fol-
lowing are the procedures for disassembling this
component from the glove box module.
Fig. 12 Glove Box Remove Install
1 - SCREW (4)
2 - SCREW (4)
Fig. 13 Glove Box Lamp & Switch Connector
1 - GLOVE BOX MODULE
2 - WIRE HARNESS CONNECTOR
AN
INSTRUMENT PANEL SYSTEM
23 - 101
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(1) Remove the glove box module from the instru-
ment panel. (Refer to 23 - BODY/INSTRUMENT
PANEL/GLOVE BOX - REMOVAL).
(2) Remove the nine screws that secure the flanges
around the perimeter of the glove box bin to the
inside of the glove box door.
(3) Remove the glove box bin from the inside of the
glove box door (Fig. 14).
(4) Remove the two screws that secure the glove
box latch and handle to the inside of the glove box
door.
(5) Remove the glove box latch and handle from
the inside of the glove box door.
ASSEMBLY
The glove box latch and handle unit of the glove
box used in this vehicle is serviced individually. Fol-
lowing are the procedures for assembling this compo-
nent to the glove box module.
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(1) Position the glove box latch and handle to the
inside of the glove box door.
(2) Install and tighten the two screws that secure
the glove box latch and handle to the inside of the
glove box door. Tighten the screws to 2 N·m (20 in.
lbs.).
(3) Position the glove box bin to the inside of the
glove box door (Fig. 14).
(4) Install and tighten the nine screws that secure
the flanges around the perimeter of the glove box bin
to the inside of the glove box door. Tighten the
screws to 2 N·m (20 in. lbs.).
(5) Reinstall the glove box module onto the instru-
ment panel. (Refer to 23 - BODY/INSTRUMENT
PANEL/GLOVE BOX - INSTALLATION).
INSTALLATION
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(1) Position the glove box module to the instru-
ment panel.
(2) If the vehicle is equipped with a glov box lamp,
reconnect the instrument panel wire harness connec-
tor to the glove box lamp and switch connector recep-
tacle (Fig. 13).
(3) Position the top of the glove box module to the
upper glove box opening reinforcement.
Fig. 14 Glove Box Latch & Handle
1 - TOP COVER
2 - GLOVE BOX LATCH & HANDLE
3 - GLOVE BOX DOOR
23 - 102
INSTRUMENT PANEL SYSTEM
AN
GLOVE BOX (Continued)
(4) Install and tighten the two outboard screws
that secure the top of the glove box module to the
upper glove box opening reinforcement (Fig. 12).
Tighten the screws to 2 N·m (20 in. lbs.).
(5) Reinstall the glove box latch striker to the
upper glove box opening reinforcement. (Refer to 23 -
BODY/INSTRUMENT PANEL/GLOVE BOX LATCH
STRIKER - INSTALLATION).
(6) Close and latch the glove box.
(7) Install and tighten the four screws that secure
the bottom of the glove box module to the instrument
panel (Fig. 12). Tighten the screws to 2 N·m (20 in.
lbs.).
(8) Install and tighten the screw that secures the
outboard end of the glove box module to the right
end of the instrument panel behind the passenger
side end cap. Tighten the screw to 2 N·m (20 in. lbs.).
(9) Reinstall the passenger side end cap onto the
instrument panel. (Refer to 23 - BODY/INSTRU-
MENT PANEL/INSTRUMENT PANEL END CAP -
INSTALLATION).
(10) Install and tighten the screw that secures the
inboard side of the glove box module to the instru-
ment panel behind the lower bezel. Tighten the screw
to 2 N·m (20 in. lbs.).
(11) Open and close the glove box to check for
proper hinge operation and alignment (Fig. 15).
(12) Reinstall the lower bezel onto the instrument
panel. (Refer to 23 - BODY/INSTRUMENT PANEL/
LOWER BEZEL - INSTALLATION).
(13) Reinstall the cluster bezel onto the instru-
ment panel. (Refer to 23 - BODY/INSTRUMENT
PANEL/CLUSTER BEZEL - INSTALLATION).
(14) Reconnect the battery negative cable.
GLOVE BOX LATCH STRIKER
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(1) Disconnect and isolate the battery negative
cable.
(2) Unlatch and open the glove box.
(3) Remove the two screws that secure the latch
striker to the upper glove box opening reinforcement
(Fig. 16).
(4) Remove the latch striker from the upper glove
box opening reinforcement.
Fig. 15 Glove Box Alignment
1 - CLUSTER BEZEL
2 - PASSENGER AIR BAG DOOR
3 - GLOVE BOX DOOR
Fig. 16 Glove Box Latch Striker Remove/Install
1 - SCREW (2)
2 - LATCH STRIKER
AN
INSTRUMENT PANEL SYSTEM
23 - 103
GLOVE BOX (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст