Dodge Dakota (R1). Manual — part 781
ASSIST HANDLE
REMOVAL
(1) Using a trim stick, remove the trim covering
the assist handle attachment screws (Fig. 5).
(2) Remove the screw attaching the assist handle
to the roof structure.
(3) Remove the assist handle.
INSTALLATION
(1) Position the assist handle on the roof structure
and headliner.
(2) Install the screws attaching the assist handle
to the headliner and roof structure.
(3) Snap in the trim covers.
B-PILLAR TRIM
REMOVAL
The B-pillar trim panel is attached to the B-pillar
with push-in fasteners.
(1) Remove door sill cover as necessary to clear
B-pillar trim.
(2) Remove shoulder belt turning loop.
(3) Grasp B-pillar trim panel and firmly pull out-
ward.
(4) Disconnect
speaker
harness
connector,
if
equipped.
(5) Route shoulder belt through access slots in
B-pillar trim panel.
(6) Separate B-pillar trim panel from B-pillar (Fig.
6).
Fig. 4 A-Pillar Trim
1 - A-PILLAR TRIM
2 - ASSIST HANDLE
3 - ASSIST HANDLE BOLTS
4 - PUSH IN COVER
5 - COWL TRIM CLIP
6 - COWL TRIM PANEL BOLT
7 - COWL TRIM PANEL
Fig. 5 Assist Handle
1 - HEADLINER
2 - GRAB HANDLE
3 - PUSH IN COVER
4 - SCREW
Fig. 6 B-Pillar Trim
1 - B-PILLAR TRIM
2 - TURNING LOOP
23 - 112
INTERIOR
AN
A-PILLAR TRIM (Continued)
INSTALLATION
(1) Position trim panel in vehicle.
(2) Route shoulder belt through access slots in
B-pillar trim panel.
(3) Connect
speaker
harness
connector,
if
equipped.
(4) Position B-pillar trim panel on B-pillar and
press to seat push-in fasteners.
(5) Install shoulder belt turning loop.
(6) Install door sill cover as necessary.
C-PILLAR TRIM
REMOVAL
(1) Remove the seat belt turning loop. (Refer to 8 -
ELECTRICAL/RESTRAINTS/SEAT
BELT
&
RETRACTOR - REMOVAL)
(2) Using a trim stick C-4755 or equivalent,
remove the upper c-pillar trim panel (Fig. 7).
(3) Remove the screws and remove position the
lower c-pillar aside.
(4) Remove the seat belt anchor and route seat
belt though the lower c-pillar trim panel.
(5) Remove the lower c-pillar trim.
INSTALLATION
(1) Place the lower c-pillar trim into the vehicle
and route the seat belt through the trim.
(2) Install the seat belt anchor. (Refer to 8 - ELEC-
TRICAL/RESTRAINTS/SEAT BELT & RETRACTOR
- INSTALLATION)
(3) Install the lower c-pillar trim and install the
screws.
(4) Install the upper c-pillar trim.
(5) Install the seat belt turning loop.
CARPETS AND FLOOR MATS
REMOVAL
(1) Remove seat.
(2) Remove door sill and cowl trim covers.
(3) Remove seat belt anchors.
(4) Remove
floor
shift
boot/floor
console,
if
equipped.
(5) Remove rear stowage tray/storage box.
(6) Pull carpet out from under quarter panel trim
and cab back panel trim.
(7) Fold carpet or mat toward center of cab.
(8) Remove carpet or mat through door opening
(Fig. 8).
INSTALLATION
(1) Position the carpet in the cab and align all
holes.
(2) Slide carpet under quarter panel trim and cab
back panel trim.
(3) Install rear stowage tray/storage box.
(4) Install floor shift boot/floor console, if equipped.
(5) Install seat belt anchors.
(6) Install door sill and cowl trim covers.
(7) Install seat.
Fig. 7 Upper C Pillar Trim
1 - UPPER C PILLAR TRAY
2 - LOWER C PILLAR TRIM SCREWS
Fig. 8 Floor Carpet or Mat
1 - CARPET
2 - CAB
AN
INTERIOR
23 - 113
B-PILLAR TRIM (Continued)
COAT HOOK
REMOVAL
(1) Grasp both sides of the coat hook base and
firmly pull outward to disengage the coat hook cover
from the base (Fig. 9) and (Fig. 10).
(2) Lift/rock the coat hook upward to disengage it
from the roof panel.
INSTALLATION
(1) Position coat hook in roof panel.
(2) Push the coat hook cover inward and secure
the coat hook to the roof panel.
COWL TRIM COVER
REMOVAL
(1) Using a trim stick, pry cowl trim cover from
cowl to disengage clips.
(2) Separate cowl trim cover from vehicle.
INSTALLATION
(1) Position cowl trim cover on cowl.
(2) Press cowl trim cover into place to engage clips.
DOOR SILL TRIM
REMOVAL
(1) Using a trim stick, pry up sill trim cover from
door sill.
(2) Separate sill trim cover from vehicle (Fig. 11).
INSTALLATION
(1) Position front edge of sill cover over cowl trim
cover and align tab.
(2) Align sill cover and press into place.
Fig. 9 Coat Hook Removal
1 - HEADLINER
2 - COAT HOOK
Fig. 10 Coat Hook
1 - CAB
2 - COAT HOOK
Fig. 11 Sill Trim Cover
1 - CLIP
2 - SILL TRIM COVER
23 - 114
INTERIOR
AN
FLOOR CONSOLE
REMOVAL
(1) Open console lid and remove bolts attaching
console to floor pan (Fig. 12).
(2) Lift the cup holder bin mat and remove bolt
attaching the console to the floor pan.
(3) Lift the cup holder mat and remove the bolts
attaching the console to the floor pan.
(4) Lift the rear of the console and pull the console
rearward to separate from the shift bezel.
(5) Remove the console from the vehicle.
INSTALLATION
(1) Position the console in the vehicle.
(2) While holding the console with the front of the
console pointing downward, position the front of the
console on top of the shift bezel.
(3) Align
rear
of
console
with
the
mounting
bracket.
(4) Install bolts attaching console to floor pan.
HEADLINER
REMOVAL
(1) Remove sun visors and visor hooks.
(2) Remove coat hooks.
(3) Remove overhead console, if equipped. Refer to
Group 8V, Overhead Console for removal procedure.
(4) Remove A-pillar trim.
(5) Remove quarter trim/B-pillar trim panels.
(6) Remove dome lamp. (Refer to 8 - ELECTRI-
CAL/LAMPS/LIGHTING - INTERIOR/DOME LAMP
- REMOVAL).
(7) Separate headliner from roof panel (Fig. 13)
and (Fig. 14).
(8) Extract headliner through door opening.
INSTALLATION
(1) Position headliner in vehicle.
(2) Install quarter/B-pillar trim panels.
(3) Install A-pillar trim.
(4) Install overhead console, if equipped.
(5) Install dome lamp. (Refer to 8 - ELECTRICAL/
LAMPS/LIGHTING - INTERIOR/DOME LAMP -
INSTALLATION).
(6) Install coat hooks.
(7) Install sun visors and visor hooks.
Fig. 12 Floor Console
1 - SHIFT BEZEL
2 - CUP HOLDER MAT
3 - ACCESSORY BIN MAT
4 - FLOOR CONSOLE
5 - BRACKET
Fig. 13 Quad Cab Headliner
1 - HEADLINER
2 - PUSH IN FASTENER
AN
INTERIOR
23 - 115
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст