Dodge Dakota (R1). Manual — part 884
TEST
ACTION
APPLICABILITY
2
Turn the ignition off.
Disconnect the PCM C2 harness connector.
Disconnect the Transmission Solenoid Assembly harness connector.
Check connectors - Clean/repair as necessary
Turn the ignition on.
Remove the Transmission Control Relay from the PDC.
Connect a jumper wire between Transmission Control Relay cavity 30 and cavity 87.
Measure the voltage of the Transmission Temperature Sensor Signal circuit in the
PCM C2 harness connector.
Is the voltage above 1.0 volt?
All
Yes
→
Repair the Transmission Temperature Sensor Signal circuit for a
short to voltage.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
No
→
3
Turn the ignition off.
Disconnect the PCM C1 and C2 harness connectors.
Disconnect the Transmission Solenoid Assembly harness connector.
Check connectors - Clean/repair as necessary
Measure the resistance between the Transmission Temperature Sensor Signal circuit
and the 5-volt Supply circuit in the Transmission Solenoid Assembly harness
connector.
Is the resistance above 100 kohms?
All
Yes
→
No
→
Repair the Transmission Temperature Sensor Signal circuit for a
short to the 5-volt Supply circuit.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
4
Turn the ignition off.
Disconnect the PCM C2 harness connector.
Disconnect the Transmission Solenoid Assembly harness connector.
Check connectors - Clean/repair as necessary
Measure the resistance of the Transmission Temperature Sensor Signal circuit
between the PCM C2 harness connector and the Transmission Solenoid Assembly
harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→
No
→
Repair the Transmission Temperature Sensor Signal circuit for
an open.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
5
Turn the ignition off.
Disconnect the PCM C2 harness connector.
Disconnect the Transmission Solenoid Assembly harness connector.
Check connectors - Clean/repair as necessary
Measure the resistance of the 5-volt Supply circuit between the PCM C2 harness
connector and the Transmission Solenoid Assembly harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→
No
→
Repair the 5-volt Supply circuit for an open.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
268
TRANSMISSION
P0713-TRANS TEMP SENSOR VOLTAGE TOO HIGH —
Continued
TEST
ACTION
APPLICABILITY
6
Turn the ignition off.
Disconnect the PCM C1 harness connector.
Disconnect the Transmission Solenoid Assembly harness connector.
Check connectors - Clean/repair as necessary
Measure the resistance of the Sensor Ground circuit between the PCM C1 harness
connector and the Transmission Solenoid Assembly harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→
No
→
Repair the Sensor Ground circuit for an open.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
7
Turn the ignition off.
Note: The Transmission Solenoid Assembly harness connector must be
connected before proceeding.
Remove the transmission oil pan.
Disconnect the Governor Pressure/Transmission Temperature Sensor connector.
Check connectors - Clean/repair as necessary
Turn the ignition on.
Measure the voltage of the Transmission Temperature Sensor Signal circuit in the
Governor Pressure/Transmission Temperature Sensor connector.
Is the voltage above 10.0 volts?
All
Yes
→
Replace the Transmission Solenoid Assembly in accordance with
the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
No
→
8
Turn the ignition off.
Remove the transmission oil pan.
Disconnect the Governor Pressure/Transmission Temperature Sensor connector.
Disconnect the Transmission Solenoid Assembly harness connector.
Measure the resistance between the Transmission Temperature Sensor Signal circuit
and 5-volt Supply circuit in the Governor Pressure/Transmission Temperature
Sensor connector.
Is the resistance above 100 kohms?
All
Yes
→
No
→
Replace the Transmission Solenoid Assembly in accordance with
the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
9
Turn the ignition off.
Disconnect the Transmission Solenoid Assembly harness connector.
Remove the transmission oil pan.
Disconnect the Governor Pressure/Transmission Temperature Sensor harness con-
nector.
Check connectors - Clean/repair as necessary
Measure the resistance of the Transmission Temperature Sensor Signal circuit
between the Transmission Solenoid Assembly connector (transmission side) and the
Governor Pressure/Transmission Temperature Sensor connector.
Is the resistance below 5.0 ohms?
All
Yes
→
No
→
Replace the Transmission Solenoid Assembly in accordance with
the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
269
TRANSMISSION
P0713-TRANS TEMP SENSOR VOLTAGE TOO HIGH —
Continued
TEST
ACTION
APPLICABILITY
10
Turn the ignition off.
Disconnect the Transmission Solenoid Assembly harness connector.
Remove the transmission oil pan.
Disconnect the Governor Pressure/Transmission Temperature Sensor connector.
Check connectors - Clean/repair as necessary
Measure the resistance of the 5-volt Supply circuit between the Transmission
Solenoid
Assembly
connector
(transmission
side)
and
Governor
Pressure/
Transmission Temperature Sensor connector.
Is the resistance below 5.0 ohms?
All
Yes
→
No
→
Replace the Transmission Solenoid Assembly in accordance with
the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
11
Turn the ignition off.
Disconnect the Transmission Solenoid Assembly harness connector.
Remove the transmission oil pan.
Disconnect the Governor Pressure/Transmission Temperature Sensor connector.
Check connectors - Clean/repair as necessary
Measure the resistance of the Sensor Ground circuit between the Transmission
Solenoid Assembly connector (transmission side) and the Governor Pressure/
Transmission Temperature Sensor connector.
Is the resistance below 5.0 ohms?
All
Yes
→
No
→
Replace the Transmission Solenoid Assembly in accordance with
the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
12
Turn the ignition off.
Remove the transmission oil pan.
Disconnect the Governor Pressure/Transmission Temperature Sensor connector.
Note: Check connectors - Clean/repair as necessary
Measure the resistance of the Transmission Temperature Sensor.
Note: Acceptable Sensor Resistance Ranges in OHMS
Sensor Temperature Minimum Maximum
-40°C (-40°F) 1094 1176
0°C (32°F) 1587 1672
25°C (77°F) 1960 2040
70°C (158°F) 2709 2860
100°C (212°F) 3284 3500
120°C (120°F) 3684 3950
150°C (302°F) 4110 4450
Is the resistance above the maximum specification for the sensor temperature?
All
Yes
→
Replace the Governor Pressure/Transmission Temperature Sen-
sor in accordance with the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
No
→
13
If there are no possible causes remaining, view repair.
All
Repair
Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
270
TRANSMISSION
P0713-TRANS TEMP SENSOR VOLTAGE TOO HIGH —
Continued
TEST
ACTION
APPLICABILITY
14
At this time, the conditions required to set the DTC are not present.
Note: Use the Freeze Frame Data to help duplicate the conditions that set
the DTC. Pay particular attention to the DTC set conditions, such as, VSS,
MAP, ECT, and Load.
Note: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
Note: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
Note: Refer to any technical service bulletins that may apply.
Were any problems found?
All
Yes
→
Repair as necessary.
Perform TRANSMISSION VERIFICATION TEST VER - 1.
No
→
Test Complete.
271
TRANSMISSION
P0713-TRANS TEMP SENSOR VOLTAGE TOO HIGH —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст