Dodge Dakota (R1). Manual — part 4
7.0
DIAGNOSTIC INFORMATION AND
PROCEDURES
13
Symptom List:
ACM ACCELEROMETER - ACTIVE
ACM ACCELEROMETER - STORED
ACM INTERNAL 1 - ACTIVE
ACM INTERNAL 1 - STORED
ACM OUTPUT DRIVER 1 - ACTIVE
ACM OUTPUT DRIVER 1 - STORED
ACM STORED ENERGY FIRING 1 - ACTIVE
ACM STORED ENERGY FIRING 1 - STORED
ACM STORED ENERGY FIRING 2 - ACTIVE
ACM STORED ENERGY FIRING 2 - STORED
ACM STORED ENERGY LOGIC - ACTIVE
ACM STORED ENERGY LOGIC - STORED
NO PCI TRANSMISSION - ACTIVE
SAFING SENSOR - ACTIVE
SAFING SENSOR - STORED
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be ACM ACCELEROMETER -
ACTIVE.
When Monitored and Set Condition:
ACM ACCELEROMETER - ACTIVE
When Monitored:
Continuously with the ignition on.
Set Condition:
The ACM has detected a diagnostic condition, replace the module.
ACM ACCELEROMETER - STORED
When Monitored:
Continuously with the ignition on.
Set Condition:
The ACM has detected a diagnostic condition, replace the module.
ACM INTERNAL 1 - ACTIVE
When Monitored:
Continuously with the ignition on.
Set Condition:
The ACM has detected a diagnostic condition, replace the module.
ACM INTERNAL 1 - STORED
When Monitored:
Continuously with the ignition on.
Set Condition:
The ACM has detected a diagnostic condition, replace the module.
ACM OUTPUT DRIVER 1 - ACTIVE
When Monitored:
Continuously with ignition on.
Set Condition:
The ACM has detected a diagnostic condition, replace the module.
14
AIRBAG
ACM OUTPUT DRIVER 1 - STORED
When Monitored:
Continuously with the ignition on.
Set Condition:
The ACM has detected a diagnostic condition, replace the module.
ACM STORED ENERGY FIRING 1 - ACTIVE
When Monitored:
Continuously with ignition on.
Set Condition:
The ACM has detected a diagnostic condition , replace the module.
ACM STORED ENERGY FIRING 1 - STORED
When Monitored:
Continuously with ignition on.
Set Condition:
The ACM has detected a diagnostic condition , replace the module.
ACM STORED ENERGY FIRING 2 - ACTIVE
When Monitored:
Continuously with ignition on.
Set Condition:
The ACM has detected a diagnostic condition , replace the module.
ACM STORED ENERGY FIRING 2 - STORED
When Monitored:
Continuously with ignition on.
Set Condition:
The ACM has detected a diagnostic condition , replace the module.
ACM STORED ENERGY LOGIC - ACTIVE
When Monitored:
Continuously with the ignition on.
Set Condition:
The ACM has detected a diagnostic condition, replace the module.
ACM STORED ENERGY LOGIC - STORED
When Monitored:
Continuously with the ignition on.
Set Condition:
The ACM has detected a diagnostic condition, replace the module.
NO PCI TRANSMISSION - ACTIVE
When Monitored:
With the ignition in the On position and the ACM transmitting
information on the PCI BUS.
Set Condition:
The code will set if the ACM cannot detect the ACM transmitting
information on the PCI BUS for 5 consecutive seconds. NOTE: Any PCI Bus Failure will
cause this code to set.
SAFING SENSOR - ACTIVE
When Monitored:
Continuously with the ignition on.
Set Condition:
The ACM has detected a diagnostic condition, replace the module.
15
AIRBAG
ACM ACCELEROMETER - ACTIVE —
Continued
SAFING SENSOR - STORED
When Monitored:
Continuously with the ignition on.
Set Condition:
The ACM has detected a diagnostic condition, replace the module.
POSSIBLE CAUSES
ACM, ACTIVE AND STORED CODE
TEST
ACTION
APPLICABILITY
1
NOTE: Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG MODULE IS DROPPED AT ANY TIME, IT MUST
BE REPLACED.
View repair.
All
Repair
Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: make sure the battery is disconnected
and wait 2 minutes before proceeding.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.
16
AIRBAG
ACM ACCELEROMETER - ACTIVE —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст