Dodge Dakota (R1). Manual — part 226
SPECIAL TOOLS
REAR AXLE
Puller C-293-PA
Adapter C-293-39
Adapter Plug SP-3289
Puller C-452
Wrench C-3281
Wrench Spanner 6958
Installer C-3718
Dummy Bearings 6776
Gauge Block 8144
Handle C-4171
3a - 14
REAR AXLE - 216RBI
R1
REAR AXLE - 216RBI (Continued)
Installer C-4076-B
Installer D-129
Remover D-103
Remover C-4307
Installer C-4198
Installer C-4308
Installer 6448
Pinion Depth 6774
Trac-Lok Set C-4487
Fixture 6963
R1
REAR AXLE - 216RBI
3a - 15
REAR AXLE - 216RBI (Continued)
Puller 7794-A
Shim Dummy 8107
Spreader W-129-B
Adapter Kit 6987B
Pilot Studs C-3288-B
Remover 6310
Puller 6790
Dial Indicator C-3339
3a - 16
REAR AXLE - 216RBI
R1
REAR AXLE - 216RBI (Continued)
AXLE SHAFTS
REMOVAL
(1) Raise and support vehicle and place transmis-
sion in neutral.
(2) Remove wheel and tire assembly.
(3) Remove brake caliper and rotor. Refer to 5
Brakes for procedure.
(4) Remove housing cover bolts and drain lubricant
from the housing.
(5) Rotate differential case so that pinion mate
gear shaft lock screw is accessible. Remove lock
screw and pinion mate gear shaft from differential
case (Fig. 20).
(6) Push axle shaft inward and remove axle shaft
C–clip lock from the axle shaft (Fig. 21).
(7) Remove axle shaft. Use care to prevent damage
to axle shaft bearing and seal, which will remain in
axle shaft tube.
(8) Inspect axle shaft seal for leakage or damage.
INSTALLATION
(1) Lubricate bearing bore and seal lip with gear
lubricant. Insert axle shaft through seal, bearing,
and engage it into side gear splines.
NOTE: Use care to prevent shaft splines from dam-
aging axle shaft seal lip.
(2) Insert C-clip lock in end of axle shaft then
push axle shaft outward to seat C-clip lock in side
gear.
(3) Insert pinion mate shaft into differential case
and through thrust washers and pinion gears.
(4) Align hole in shaft with hole in the differential
case and install lock screw with Loctite
t on the
threads. Tighten lock screw to 19 N·m (14 ft. lbs.).
(5) Install cover and fill differential with gear
lubricant.
(6) Install brake drum, refer to 5 Brakes for proce-
dures.
(7) Install wheel and tire an lower vehicle.
AXLE BEARING AND SEAL
REMOVAL
(1) Remove the axle shaft.
(2) Remove shaft seal from the axle shaft tube
with a small pry bar.
NOTE: The seal and bearing can be removed at the
same time with the bearing removal tool.
(3) Remove the axle shaft bearing from the tube
(Fig. 22) with Bearing Removal Tool Set 6310 using
Adapter Foot 6310-6.
(4) Inspect the axle shaft tube bore for roughness
and burrs. Remove as necessary.
INSTALLATION
(1) Wipe the bore in the axle shaft tube clean.
(2) Install axle shaft bearing with Installer C-4198
and Handle C-4171. Ensure part number on the
bearing is against the installer.
(3) Install new axle shaft seal with Installer
C–4076–B and Handle C-4171.
(4) Install the axle shaft.
Fig. 20 Mate Shaft Lock Screw
1 - LOCK SCREW
2 - PINION GEAR MATE SHAFT
Fig. 21 Axle Shaft C–Clip Lock
1 - C-CLIP LOCK
2 - AXLE SHAFT
3 - SIDE GEAR
R1
REAR AXLE - 216RBI
3a - 17
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст