Dodge Nitro. Manual — part 634
1) TEST FOR INTERMITTENT CONDITION
Turn the ignition on.
With the scan tool, clear all DTC's
Turn the Left Turn Signal on.
With the scan tool, read DTC's.
Does the scan tool display active: B17BF-LEFT SIDEMARKER LAMP CONTROL CIRCUIT
OVERCURRENT?
Yes
Go to 2).
No
The condition that caused this symptom is currently not present. Check for an intermittent
condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken
wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded, or
contaminated terminals. Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1 .
2) LEFT REAR TURN SIGNAL BULB
Turn the ignition off.
Remove Left Rear Turn Signal Bulb.
Inspect the Left Rear Turn Signal Bulb.
Is the inoperative bulb OK?
Yes
Go to 3).
No
Replace the Inoperative bulb in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1 .
3) (L163) LEFT SIDEMARKER LAMP CONTROL CIRCUIT SHORT TO GROUND
Disconnect the TIPM C4 harness connector.
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro
Disconnect the Left Sidemarker Lamp harness connector.
Measure the resistance between ground and the (L163) Left Sidemarker Lamp Control circuit.
Is the resistance above 10k ohms?
Yes
Go to 4).
No
Repair the (L163) Left Sidemarker Lamp Control circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1 .
4) (L163) LEFT SIDEMARKER LAMP CONTROL CIRCUIT SHORTED TO VOLTAGE
Turn the ignition on.
Measure for voltage on the (L163) Left Sidemarker Lamp Control circuit.
Is there any voltage present?
Yes
Repair the (L163) Left Sidemarker Lamp Control circuit short to voltage.
Perform BODY VERIFICATION TEST - VER 1 .
No
Replace the Totally Integrated Power Module (TIPM) in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1 .
B17C2-RIGHT SIDEMARKER LAMP CONTROL CIRCUIT HIGH
For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article.
When Monitored:
Continuously.
Set Condition:
When the Totally Integrated Power Module (TIPM) detects a HIGH condition.
Possible Causes
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro
Diagnostic Test
1) TEST FOR INTERMITTENT CONDITION
Turn the ignition on.
With the scan tool, clear all DTC's
Turn the Right Turn Signal on.
With the scan tool, read DTC's.
Does the scan tool display active: B17C2-RIGHT SIDEMARKER LAMP CONTROL CIRCUIT
HIGH?
Yes
Go to 2).
No
The condition that caused this symptom is currently not present. Check for an intermittent
condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken
wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded, or
contaminated terminals. Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1 .
2) RIGHT REAR TURN SIGNAL BULB
Turn the ignition off.
Remove Right Rear Turn Signal Bulb.
Inspect the Right Rear Turn Signal Bulb.
Is the inoperative bulb OK?
Yes
Go to 3).
No
(L162) RIGHT SIDEMARKER LAMP CONTROL CIRCUIT OPEN
(L162) RIGHT SIDEMARKER LAMP CONTROL CIRCUIT SHORTED TO VOLTAGE
TOTALLY INTEGRATED POWER MODULE
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro
Replace the Inoperative bulb in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1 .
3) (L162) RIGHT SIDEMARKER LAMP CONTROL CIRCUIT OPEN
Disconnect the TIPM C4 harness connector.
Disconnect the Right Sidemarker Lamp assembly harness connector.
Measure the resistance of the (L162) Right Sidemarker Lamp Control circuit between the Right
Sidemarker Lamp assembly harness connector and the TIPM C4 harness connector.
Does the ohm meter read open circuit?
Yes
Repair the (L162) Right Sidemarker Lamp Control circuit for an open.
Perform BODY VERIFICATION TEST - VER 1 .
No
Go to 4).
4) (L162) RIGHT SIDEMARKER LAMP CONTROL CIRCUIT SHORTED TO VOLTAGE
Turn the ignition on.
Measure for voltage on the (L162) Right Sidemarker Lamp Control circuit.
Is there any voltage present?
Yes
Repair the (L162) Right Sidemarker Lamp Control circuit short to voltage.
Perform BODY VERIFICATION TEST - VER 1 .
No
Replace the Totally Integrated Power Module (TIPM) in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1 .
B17C4-RIGHT SIDEMARKER LAMP CONTROL CIRCUIT OVERCURRENT
For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article.
When Monitored:
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст