Dodge Nitro. Manual — part 75
Fig. 41: Installing P/S Pump
Courtesy of CHRYSLER LLC
31. Install the P/S pump (2).
Fig. 42: Installing A/C Lines
Courtesy of CHRYSLER LLC
32. Install the A/C lines (1,3).
33. Evacuate and recharge air conditioning.
34. Install the hood.
2007 Dodge Nitro R/T
2007 ENGINE 4.0L - Service Information - Nitro
Fig. 43: Removing Battery Cable
Courtesy of CHRYSLER LLC
35. Connect the negative battery cable (2).
36. Start engine and run until operating temperature is reached.
37. Check all fluid levels and properly fill.
SPECIFICATIONS
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
DESCRIPTION
N.m
Ft. Lbs.
In. Lbs.
Camshaft Sprocket Bolt Right Side
102 +1/4
Turn
75 +1/4
Turn
-
Camshaft Sprocket Bolt Left Side
102 +1/4
Turn
75 +1/4
Turn
-
Camshaft Thrust Plate Bolts
28
-
250
Connecting Rod Cap Bolts
27 +1/4
Turn
20 +1/4
Turn
-
Crankshaft Main Bearing Cap
-
-
-
Inner Main Cap Bolts
20 +1/4
Turn
15 +1/4
Turn
-
Outer Main Cap Bolts
27 +1/4
Turn
20 +1/4
Turn
-
Tie Bolts (Horizontal)
28
-
250
Crankshaft Damper-Bolt
95
70
-
Cylinder Head Bolts*
-
-
-
2007 Dodge Nitro R/T
2007 ENGINE 4.0L - Service Information - Nitro
4.0L ENGINE - SPECIFICATIONS
Step 1
61
45
-
Step 2
88
65
-
Step 3
88
65
-
Step 4 +1/4 Turn
+1/4 Turn
-
*Refer to procedure for tightening sequence. See INSTALLATION.
Cylinder Head Cover Bolts
10
-
90
Exhaust Manifold to Cylinder Head Bolts
28
-
250
Exhaust Manifold Heat Shield Bolts
12
-
105
Flex plate to Crankshaft
95
70
-
Flex plate to Torque Converter
75
55
-
Intake Manifold - Lower
28
-
250
Intake Manifold - Upper
12
-
105
Left Engine Mount to Cradle
75
55
-
Oil Cooler Connector Bolt
54
40
-
Oil Pan
-
-
-
M6 Bolts
12
-
105
M8 Bolts
28
-
250
Oil Pan Drain Plug
27
20
-
Oil Filter
16
12
-
M8 Oil Pump to Block Bolts
28
-
250
M6 Oil Pump Cover Bolts
12
-
105
Oil Pump Pick Up Tube Bolt
28
-
250
Windage Tray
28 + 90°
20 + 90°
-
Crankshaft Rear Seal Retainer
12
-
105
Right Engine Mount to Cradle
75
55
-
Rocker Shaft Pedestal Retaining Bolts
31
-
275
Spark Plugs
28
20
-
Timing Belt Tensioner Bolts
28
-
250
Timing Belt Tensioner Pulley Assembly Bolt
61
45
-
Timing Belt Cover
-
-
-
M6 Bolts
12
-
105
M8 Bolts
28
-
250
M10 Bolts
54
40
-
Upper Engine Mount to Frame Rail
68
50
-
Upper Engine Mount to timing Cover
54
40
-
DESCRIPTION
SPECIFICATION
Type
60° SOHC V-6 24-Valve
Displacement
4.0L
2007 Dodge Nitro R/T
2007 ENGINE 4.0L - Service Information - Nitro
CYLINDER BLOCK
PISTONS
PISTON PINS
PISTON RINGS
Firing Order
1-2-3-4-5-6
Compression Ratio
10:2:1
Lead Cylinder
#1 Right Bank
Metric
Standard
Displacement
4.0L Liters
244 cu. in.
Bore
96.0 mm
3.780 in.
Stroke
91.0 mm
3.583 in.
DESCRIPTION
SPECIFICATIONS
Metric
Standard
Cylinder Bore Diameter
96.0 mm ± 0.0076
3.780 in. ± 0.0003 in.
Out-of-Round (Max.)
0.006 mm
0.00023 in.
Taper (Max.)
0.051 mm
0.002 in.
DESCRIPTION
SPECIFICATIONS
Metric
Standard
Material Type
Aluminum (Full Floating Pins)
Piston Diameter
95.98 mm ± 0.019 mm
3.7788 in. ± 0.0008 in.
Clearance at Size Location
-0.007 to +0.047 mm
-0.003 to +0.0018 in.
Piston Weight - A
374.4-379.4 grams
13.21-13.38 oz.
Piston Weight - B
379.5-384.4 grams
13.38-13.56 oz.
Piston Ring Groove Diameter #1
87.4-87.6 mm
3.441-3.449 in.
Piston Ring Groove Diameter #2
86.3-86.5 mm
3.397-3.4055 in.
Piston Ring Groove Diameter #3
86.5-86.7 mm
3.406-3.413 in.
DESCRIPTION
SPECIFICATIONS
Metric
Standard
Type
Full Floating
Clearance in Piston
0.005-0.015 mm
0.002-0.0006 in.
Clearance in Rod
0.007-0.018 mm
0.0003-0.007 in.
Diameter
21.997-22.000 mm
0.8662-0.8660 in.
DESCRIPTION
SPECIFICATIONS
Metric
Standard
Ring Gap-Top Compression Ring
0.20-0.36 mm
0.008-0.014 in.
Ring Gap-2nd Compression Ring
(Micro-Napier
0.20-0.40 mm
0.0078-0.0157 in.
2007 Dodge Nitro R/T
2007 ENGINE 4.0L - Service Information - Nitro
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст