Dodge Nitro. Manual — part 344
2007 AUTOMATIC TRANSMISSION
NAG1 - Shifter Diagnostics - Nitro
DIAGNOSTIC CODE INDEX
DIAGNOSTIC CODE INDEX
NAG1 - SHIFTER DIAGNOSTICS
DIAGNOSIS AND TESTING
P0562-BATTERY VOLTAGE LOW - ESM
For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article.
Theory of Operation
The Shift Lever Assembly (SLA) controller (Electronic Shift Module - ESM) monitors ignition voltage. The
DTC will set if the monitored battery voltage drops below 6.0 volts and a temporary limp in will be activated. If
the voltage rises above 9.0 volts, normal operations is resumed.
When Monitored:
Continuously with the ignition in the run position.
Set Condition:
When monitored battery voltage drops below 6.0 volts.
DTC
Description
P0562
BATTERY VOLTAGE LOW - ESM
P0563
BATTERY VOLTAGE HIGH - ESM
P0607
ECU INTERNAL PERFORMANCE - ESM
P0930
BTSI CONTROL CIRCUIT LOW - ESM
P0931
BTSI CONTROL CIRCUIT HIGH - ESM
P2775
AUTOSTICK UPSHIFT SWITCH CIRCUIT PERFORMANCE - ESM
P2779
AUTOSTICK DOWNSHIFT SWITCH CIRCUIT PERFORMANCE - ESM
U0002
CAN C BUS OFF PERFORMANCE - ESM
U0100
LOST COMMUNICATION WITH ECM/PCM - ESM
U0121
LOST COMMUNICATION WITH ANTI-LOCK BRAKE MODULE - ESM
U0141
LOST COMMUNICATION WITH FRONT CONTROL MODULE - ESM
Possible Causes
VEHICLE CHARGING SYSTEM
2007 Dodge Nitro R/T
2007 AUTOMATIC TRANSMISSION NAG1 - Shifter Diagnostics - Nitro
2007 Dodge Nitro R/T
2007 AUTOMATIC TRANSMISSION NAG1 - Shifter Diagnostics - Nitro
Always perform the NAG1 Pre-Diagnostic Troubleshooting procedure before proceeding.
Diagnostic Test
1) CHECK FOR ENGINE CHARGING SYSTEM DTCS
With the scan tool, read Engine DTCs.
Are there any Engine Charging System DTCs present?
Yes
Refer to appropriate Engine Electrical Diagnostics article and perform the appropriate symptom.
Perform NAG1 TRANSMISSION VERIFICATION TEST.
No
Go to 2).
2) CHECK (F1) IGNITION UNLOCK RUN START CIRCUIT
(F1) IGNITION UNLOCK RUN START CIRCUIT
(Z910) GROUND CIRCUITS
SHIFT LEVER ASSEMBLY
2007 Dodge Nitro R/T
2007 AUTOMATIC TRANSMISSION NAG1 - Shifter Diagnostics - Nitro
Fig. 1: Using 12-Volt Test Light Connected To Ground To Check (F1) Ignition Unlock Run Start
Circuit In Shift Lever Assembly Harness Connector
Courtesy of CHRYSLER LLC
Turn the ignition off to the lock position.
Disconnect the Shift Lever Assembly harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the (F1) Ignition Unlock Run Start circuit in the
Shift Lever Assembly harness connector.
Does the test light illuminate brightly?
NOTE:
The test light must illuminate brightly. Compare the brightness to that of a
direct connection to the battery.
2007 Dodge Nitro R/T
2007 AUTOMATIC TRANSMISSION NAG1 - Shifter Diagnostics - Nitro
Yes
Go to 3).
No
Repair the (F1) Ignition Unlock Run Start circuit for high resistance.
Perform NAG1 TRANSMISSION VERIFICATION TEST.
3) CHECK (Z910) GROUND CIRCUITS
Fig. 2: Using 12-Volt Test Light Connected To 12-Volts To Check (Z910) Ground Circuit In Shift
Lever Assembly Harness Connector
Courtesy of CHRYSLER LLC
Turn the ignition off to the lock position.
Using a 12-volt test light connected to 12-volts, check the (Z910) Ground circuit in the Shift Lever
Assembly harness connector.
Does the test light illuminate brightly?
Yes
Go to 4).
Perform NAG1 TRANSMISSION VERIFICATION TEST.
No
NOTE:
The test light must illuminate brightly. Compare the brightness to that of a
direct connection to the battery.
2007 Dodge Nitro R/T
2007 AUTOMATIC TRANSMISSION NAG1 - Shifter Diagnostics - Nitro
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст