Dodge Nitro. Manual — part 626
No
Go to 5).
5) (L54) RIGHT STOP LAMP CONTROL CIRCUIT OPEN
Turn the ignition off.
Disconnect the TIPM C7 connector.
Measure the resistance of the (L54) Right Stop Lamp Control circuit between the Right Rear Tail Lamp
harness connector and the TIPM C7 harness connector.
Is the resistance below 10.0 ohms?
No
Go to 6).
Yes
Repair the (L54) Right Stop Lamp Control circuit for an open.
Perform BODY VERIFICATION TEST - VER 1 .
6) (L54) RIGHT STOP LAMP CONTROL CIRCUIT SHORTED TO VOLTAGE
Turn the ignition on.
Measure the voltage between (L54) Right Stop Lamp Control circuit and ground.
Is there any voltage present?
Yes
Repair the (L54) Right Stop Lamp Control circuit for a short to voltage.
Perform BODY VERIFICATION TEST - VER 1 .
No
Replace the Totally Integrated Power Module (TIPM) in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1 .
B1647-REAR RIGHT TURN CONTROL CIRCUIT LOW
For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article.
When Monitored:
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro
With the Turn Signal activated.
Set Condition:
When the Totally Integrated Power Module (TIPM) detects a LOW condition.
Diagnostic Test
1) INTERMITTENT CONDITION
Turn the ignition on.
With the scan tool, clear all DTC's.
Turn the Right Turn Signal on.
With the scan tool, read DTC's.
Does the scan tool display active: B1647-REAR RIGHT TURN LAMP CONTROL CIRCUIT
LOW?
Yes
Go to 2).
No
The condition that caused this symptom is currently not present. Check for an intermittent
condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken
wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded, or
contaminated terminals. Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1 .
2) REAR RIGHT TURN SIGNAL BULB
Turn the ignition off.
Disconnect the Right Rear Turn Signal Bulb.
Turn the ignition on.
With the scan tool, read DTC's.
Possible Causes
(L62) RIGHT REAR TURN SIGNAL CONTROL CIRCUIT SHORT TO GROUND
RIGHT REAR TURN SIGNAL BULB
TOTALLY INTEGRATED POWER MODULE
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro
Does the DTC reset?
Yes
Go to 3).
No
Replace the Right Rear Turn Signal Bulb in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1 .
3) (L62) RIGHT REAR TURN SIGNAL CONTROL CIRCUIT SHORT TO GROUND
Turn the ignition off.
Disconnect the TIPM C7 harness connector.
Disconnect the Right Rear Tail Lamp harness connector.
Measure the resistance between ground and the (L62) Right Rear Turn Signal Control circuit.
Is the resistance above 10k ohms?
Yes
Replace the Totally Integrated Power Module (TIPM) in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1 .
No
Repair the (L62) Right Rear Turn Signal Control circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1 .
B1648-REAR RIGHT TURN CONTROL CIRCUIT HIGH
For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article.
When Monitored:
Continuously.
Set Condition:
When the Totally Integrated Power Module (TIPM) detects a HIGH condition.
Possible Causes
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro
Diagnostic Test
1) TEST FOR INTERMITTENT CONDITION
Turn the ignition on.
With the scan tool, clear all DTC's.
Turn the Right Turn Signal on.
With the scan tool, read DTC's.
Does the scan tool display active: B1648-REAR RIGHT TURN LAMP CONTROL CIRCUIT
HIGH?
Yes
Go to 2).
No
The condition that caused this symptom is currently not present. Check for an intermittent
condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken
wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded, or
contaminated terminals. Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1 .
2) CHECK (Z910) GROUND CIRCUITS
Turn the ignition off.
Disconnect the Right Rear Turn Signal Lamp assembly harness connector.
With a 12-volt test light connected to 12-volts, probe each (Z910) Ground circuit.
Does the test light illuminate brightly on each ground circuit?
Yes
Go to 4).
CHECK (Z910) GROUND CIRCUIT
(Z910) GROUND CIRCUIT OPEN
CHECK (L62) RIGHT REAR TURN SIGNAL CONTROL CIRCUIT
(L62) RIGHT REAR TURN SIGNAL CONTROL CIRCUIT OPEN
(L62) RIGHT REAR TURN SIGNAL CONTROL CIRCUIT SHORTED TO VOLTAGE
TOTALLY INTEGRATED POWER MODULE
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Electrical/Diagnostics - Nitro
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст