Dodge Nitro. Manual — part 282
Fig. 61: Measuring Resistance Between (X202) Amplified Right I/P Speaker (+) Circuit And (X292)
Amplified Right I/P Speaker (-) Circuit
Courtesy of CHRYSLER LLC
Disconnect the Amplifier C2 harness connector.
Measure the resistance between the (X202) Amplified Right I/P Speaker (+) circuit, and the (X292)
Amplified Right I/P Speaker (-) circuit.
Is the resistance below 10K ohms?
Yes
Repair the (X202) Amplified Right I/P Speaker (+) circuit, and the (X292) Amplified Right I/P
Speaker (-) circuit for a short together.
Perform BODY VERIFICATION TEST - VER 1 .
No
Replace the amplifier in accordance with the service information.
Perform BODY VERIFICATION TEST - VER 1 .
B146A-CHANNEL 3 AUDIO SPEAKER OUTPUT CIRCUIT PERFORMANCE
For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article.
When Monitored:
With the ignition on.
Set Condition:
This DTC will set if a DC offset occurs on the output channel, the amplifier shall set a DTC after a
maturity rate of 5 ±1 sec.
Diagnostic Test
1) CHECK FOR AN INTERMITTENT CONDITION
Turn the ignition on, then off, and then on again.
With the scan tool, read Amplifier DTCs.
Does the scan tool display active: B146A-CHANNEL 3 AUDIO SPEAKER OUTPUT CIRCUIT
PERFORMANCE?
Possible Causes
AMPLIFIER
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Audio/Video Systems - Electrical Diagnostics - Nitro
Yes
Replace the amplifier in accordance with the service information.
Perform BODY VERIFICATION TEST - VER 1 .
No
The conditions that caused this code to set are not present at this time. Using the wiring
diagram/schematic as a guide, inspect the wiring and connectors.
Perform BODY VERIFICATION TEST - VER 1 .
B146B-CHANNEL 3 AUDIO SPEAKER OUTPUT CIRCUIT LOW
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Audio/Video Systems - Electrical Diagnostics - Nitro
Fig. 62: Channel 3 Audio Speaker Output Circuit Schematic
Courtesy of CHRYSLER LLC
For complete wiring diagrams refer to SYSTEM WIRING DIAGRAMS article.
When Monitored:
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Audio/Video Systems - Electrical Diagnostics - Nitro
With the ignition on.
Set Condition:
The amplifier detects a shorted to ground condition on the speaker output circuit.
Diagnostic Test
1) CHECK FOR AN INTERMITTENT CONDITION
Turn the ignition on, then off, and then on again.
With the scan tool, read Amplifier DTCs.
Does the scan tool display active: B146B-CHANNEL 3 AUDIO SPEAKER OUTPUT CIRCUIT
LOW?
Yes
Go to 2).
No
The condition that caused this symptom is currently not present. Check for an intermittent
condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken
wires. Also, inspect the related connectors for broken, bent, pushed out, spread, corroded, or
contaminated terminals. Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1 .
2) CHECK THE (X209) AMPLIFIED LEFT FRONT SPEAKER (+) CIRCUIT FOR A SHORT
TO GROUND
Possible Causes
(X209) AMPLIFIED LEFT FRONT SPEAKER (+) CIRCUIT SHORTED TO GROUND
(X299) AMPLIFIED LEFT FRONT SPEAKER (-) CIRCUIT SHORTED TO GROUND
LEFT FRONT SPEAKER
AMPLIFIER
2007 Dodge Nitro R/T
2007 ACCESSORIES AND EQUIPMENT Audio/Video Systems - Electrical Diagnostics - Nitro
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст