Dodge Viper SRT-10 (ZB). Manual — part 78
MULTI-FUNCTION SWITCH CONTINUITY TEST
SWITCH POSITION
MODE
CONTINUITY BETWEEN
TURN SIGNAL IN NEUTRAL
HAZARD WARNING SWITCH OFF
HAZARD OFF
B-1 AND B-4
B-1 AND B-5
B-18 AND B-19
B-4 AND B-5
TURN SIGNAL ON
HAZARD WARNING SWITCH OFF
LEFT TURN
A-2 AND B-2
A-2 AND B-4
B-1 AND B-5
B-2 AND B-4
RIGHT TURN
A-2 AND B-5
B-1 AND B-4
B-5 AND B-6
TURN SIGNAL IN NEUTRAL
HAZARD WARNING SWITCH ON
HAZARD ON
A-2 AND B-2
A-2 AND B-4
A-2 AND B-5
A-2 AND B-6
A-3 AND A-5
A-3 AND B-7
B-2 AND B-4
B-2 AND B-5
B-2 AND B-6
B-4 AND B-5
B-4 AND B-6
B-5 AND B-6
PARK LAMP
PARK
B-9 AND B-20
HEADLAMP BEAM
LOW
B-16 AND B-18
B-16 AND B-19
B-9 AND B-20
B-1 AND B-4
HIGH
B-17 AND B-18
B-17 AND B-19
B-9 AND B-20
B-1 AND B-4
OPTICAL HORN
ON
B-17 AND B-18
B-17 AND B-19
FRONT FOG
ON
B-13 AND B-14
B-9 AND B-20
B-16 AND B-18
B-16 AND B-19
8L - 20
LAMPS
ZB
MULTI-FUNCTION SWITCH (Continued)
MULTI-FUNCTION SWITCH DIMMER CONTROL RESISTANCE
SWITCH POSITION
RESISTANCE VALUE BETWEEN PINS 7 AND 8
DOME ON
150 OHMS
PARADE MODE
411 OHMS
DIM 6 (BRIGHTEST INTENSITY)
768 OHMS
DIM 5
1221 OHMS
DIM 4
1825 OHMS
DIM 3
2593 OHMS
DIM 2
3793 OHMS
DIM 1 (DIMMEST INTENSITY)
5653 OHMS
DEFEAT
8813 OHMS
REMOVAL
(1) Open deck lid.
(2) Remove four bolts to battery compartment
cover and remove cover.
(3) Disconnect and isolate the battery negative
cable.
(4) Remove both upper and lower steering column
shrouds.
(5) Disconnect both posi-lock harness connectors at
the rear of the multi-function switch (Fig. 19) and
(Fig. 20).
(6) Remove multi-function switch mounting screws
(Fig. 19) and (Fig. 20).
(7) The windshield wiper/washer switch must be
transferred to the new multi-function switch. (Refer
to 8 - ELECTRICAL/WIPERS/WASHERS/WIPER/
WASHER SWITCH - REMOVAL).
INSTALLATION
(1) The windshield wiper/washer switch must be
transferred to the new multi-function switch. (Refer
to 8 - ELECTRICAL/WIPERS/WASHERS/WIPER/
WASHER SWITCH - INSTALLATION).
(2) Install the multi-function switch mounting
screws. Tighten multi-function switch to column
retaining screws to 3 N·m (27 in. lbs.) torque.
(3) Connect both posi-lock harness connectors at
the rear of the multi-function switch.
(4) Instal both upper and lower steering column
shrouds.
(5) Connect the battery negative cable.
(6) Place battery access cover into place and install
four bolts.
(7) Close deck lid.
(8) Verify vehicle and system operation.
Fig. 19 MULTI-FUNCTION SWITCH MOUNTING
1 - MULTI-FUNCTION SWITCH CONNECTOR
2 - HAZARD/WARNING SWITCH
3 - WINDSHIELD WIPER/WASHER SWITCH CONNECTOR
4 - MOUNTING SCREWS
5 - COMBINATION FLASHER
ZB
LAMPS
8L - 21
MULTI-FUNCTION SWITCH (Continued)
Fig. 20 MULTI-FUNCTION SWITCH - REMOVE/INSTALL
1 - MULTI-FUNCTION SWITCH CONNECTORS
3 - MULTI-FUNCTION SWITCH
2 - RETAINING SCREWS
8L - 22
LAMPS
ZB
MULTI-FUNCTION SWITCH (Continued)
MULTI-FUNCTION SWITCH -
EXPORT
DESCRIPTION
The multi-function switch is secured to the upper
steering column housing at the top of the steering
column, just behind the steering wheel (Fig. 21). The
visible parts of the multi-function switch are the turn
signal control stalk w/exterior lighting controls that
extends through a dedicated opening in the left side
of the upper steering column shrouds, the windshield
wiper/washer stalk that extends through a dedicated
opening in the right side of the upper steering col-
umn shrouds, and the hazard warning switch push
button that protrudes through an opening in the
upper steering column shroud on the top of the steer-
ing column. The remainder of the switch, its mount-
ing provisions, and its electrical connections are all
concealed beneath the steering column shrouds. The
multi-function switch control stalk has both nomen-
clature and International Control and Display Sym-
bol graphics applied to it, which identify its many
functions. An International Control and Display Sym-
bol icon for “Hazard Warning” is applied to the top of
the hazard warning switch push button.
The switch housing and its controls are constructed
of molded black plastic. A connector receptacle with
up to twenty terminals is located on the back of the
switch housing and connects the switch to the vehicle
electrical system through a take out and connector of
the instrument panel wire harness.
The multi-function switch supports the following
functions and features:
• Continuous Wipe Modes - The control knob of
the multi-function switch provides two continuous
wipe switch positions, low speed or high speed.
• Intermittent Wipe Mode - The control knob of
the multi-function switch provides an intermittent
wipe mode with multiple delay interval positions.
• Washer Mode - The control stalk of the multi-
function switch provides washer system operation
when the button is pulled towards the driver.
• Wiper Mist Mode - Mist will cycle wipers when
stalk is pulled down.
• Hazard Warning Control - The internal cir-
cuitry and hardware of the multi-function switch pro-
vide detent switching for activation and deactivation
of the hazard warning system.
• Exterior Lighting Control - The internal cir-
cuitry and hardware of the multi-function switch pro-
vides an input to the BCM and the BCM controls for
activation and deactivation of exterior lighting.
• Headlamp Beam Selection - The internal cir-
cuitry and hardware of the multi-function switch pro-
vides an input to the BCM and the BCM controls
detent switching for selection of the headlamp high
or low beams.
Fig. 21 MULTI-FUNCTION SWITCH
1 - TURN SIGNAL CONTROL STALK
5 - CANCELLING CAM
2 - HAZARD WARNING SWITCH
6 - PANEL DIMMER/INTERIOR LIGHT SWITCH
3 - WINDSHIELD WIPER/WASHER CONTROL
7 - EXTERIOR LIGHTING CONTROL/FOG LAMP
4 - WINDSHIELD WIPER/WASHER SWITCH RETAINING SCREWS
ZB
LAMPS
8L - 23
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст