Dodge Viper SRT-10 (ZB). Manual — part 309
Symptom:
PASSENGER SQUIB 2 SHORT TO BATTERY
When Monitored and Set Condition:
PASSENGER SQUIB 2 SHORT TO BATTERY
When Monitored:
When the ignition is on, the ACM monitors the voltage of the Passenger
Squib 2 circuits.
Set Condition:
The ACM has detected high voltage on the Passenger Squib 2 circuits.
POSSIBLE CAUSES
PASSENGER AIRBAG CIRCUIT SHORT TO BATTERY
PASSENGER SQUIB 2 LINE 1 OR LINE 2 SHORTED TO BATTERY
ACM, PASSENGER SQUIB 2 CIRCUIT SHORT TO BATTERY
STORED CODE OR INTERMITTENT CONDITION
ACTIVE CODE PRESENT
TEST
ACTION
APPLICABILITY
1
NOTE: Ensure that the battery is fully charged.
Turn the ignition on.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ACTIVE or STORED DTC:
All
ACM - ACTIVE DTC
ACM - STORED DTC
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
2
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Passenger Airbag connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Passenger Airbag connector.
WARNING: TURN THE IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t, read the active Airbag DTCs.
Does the DRB show PASSENGER SQUIB 2 CIRCUIT SHORT TO BATTERY?
All
Yes
→ Go To 3
No
→ Replace Passenger Airbag in accordance with the Service Infor-
mation.
Perform AIRBAG VERIFICATION TEST - VER 1.
129
AIRBAG
TEST
ACTION
APPLICABILITY
3
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
Disconnect the Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool adaptor to the Airbag Control Module connector.
WARNING: TURN THE IGNITION ON, THEN RECONNECT THE BATTERY.
Disconnect the Load Tool from the Passenger Airbag connector.
Measure the voltage on the Passenger Squib 2 Line 1 and Line 2 circuits between the
Passenger Airbag connector and ground.
Is there any voltage present?
All
Yes
→ Repair Passenger Squib 2 Line 1 or Line 2 circuit shorted to
battery.
Perform AIRBAG VERIFICATION TEST - VER 1.
No
→ Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: IF THE AIRBAG CONTROL MODULE
IS DROPPED AT ANY TIME, IT MUST BE REPLACED.
Perform AIRBAG VERIFICATION TEST - VER 1.
4
NOTE: Ensure the battery is fully charged.
With the DRBIII
t, record and erase all DTCs from all modules.
All active codes must be resolved before diagnosing any stored codes.
Maintain a safe distance from all airbags while performing the following steps.
With the DRBIII
t monitor active codes as you work through the system.
NOTE: If equipped with Passenger Airbag On-Off switch, read the DTC’s in
all switch positions.
Wiggle the wiring harness and connectors of the appropriate airbag system and
rotate the steering wheel from stop to stop.
NOTE: Check connectors - Clean and repair as necessary.
You have just attempted to simulate the condition that initially set the trouble code
message.
The following additional checks may assist you in identifying a possible intermittent
problem:
- Visually inspect related wire harness connectors. Look for broken, bent, pushed out,
spread, corroded, or contaminated terminals.
- Visually inspect the related harnesses. Look for chafed, pierced, pinched or partially
broken wire.
- Refer to Wiring Diagrams and Technical Service Bulletins that may apply.
Did the DTC become active ?
All
Yes
→ Select appropriate symptom from Symptom List.
No
→ No problem found at this time. Erase all codes before returning
vehicle to customer.
130
AIRBAG
PASSENGER SQUIB 2 SHORT TO BATTERY —
Continued
Symptom:
PASSENGER SQUIB 2 SHORT TO GROUND
When Monitored and Set Condition:
PASSENGER SQUIB 2 SHORT TO GROUND
When Monitored:
When the ignition is on, the ACM monitors the resistance of the
Passenger Squib 2 circuits for low resistance.
Set Condition:
The ACM has detected a short to ground in the Passenger Squib 2 circuits.
POSSIBLE CAUSES
PASSENGER AIRBAG CIRCUIT SHORTED TO GROUND
PASSENGER SQUIB 2 LINE 1 OR LINE 2 SHORT TO GROUND
ACM, PASSENGER SQUIB 2 CIRCUIT SHORT TO GROUND
STORED CODE OR INTERMITTENT CONDITION
ACTIVE CODE PRESENT
TEST
ACTION
APPLICABILITY
1
NOTE: Ensure that the battery is fully charged.
Turn the ignition on.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ACTIVE or STORED DTC:
All
ACM - ACTIVE DTC
ACM - STORED DTC
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
2
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Passenger Airbag connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Passenger Airbag connector.
WARNING: TURN THE IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t, read the active Airbag DTCs.
Does the DRB show PASSENGER SQUIB 2 CIRCUIT SHORT TO GROUND?
All
Yes
→ Go To 3
No
→ Replace the Passenger Airbag in accordance with the Service
Information.
Perform AIRBAG VERIFICATION TEST - VER 1.
131
AIRBAG
TEST
ACTION
APPLICABILITY
3
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Airbag Control Module connector
NOTE: Check connectors - Clean repair as necessary.
Connect the appropriate Load Tool adaptor to the Airbag Control Module connector.
Disconnect the Load Tool from the Passenger Airbag connector.
Measure the resistance of the Passenger Squib 2 Line 1 and Line 2 circuits between
the Passenger Airbag Module connector and ground.
Is the resistance below 10K ohms on either circuit?
All
Yes
→ Repair Passenger Squib 2 Line 1 or Line 2 circuit for a shorted to
ground.
Perform AIRBAG VERIFICATION TEST - VER 1.
No
→ Replace the Airbag Control Module in accordance with Service
Instructions. WARNING: IF THE AIRBAG CONTROL MODULE
IS DROPPED AT ANY TIME, IT MUST BE REPLACED.
Perform AIRBAG VERIFICATION TEST - VER 1.
4
NOTE: Ensure the battery is fully charged.
With the DRBIII
t, record and erase all DTCs from all modules.
All active codes must be resolved before diagnosing any stored codes.
Maintain a safe distance from all airbags while performing the following steps.
With the DRBIII
t monitor active codes as you work through the system.
NOTE: If equipped with Passenger Airbag On-Off switch, read the DTC’s in
all switch positions.
Wiggle the wiring harness and connectors of the appropriate airbag system and
rotate the steering wheel from stop to stop.
NOTE: Check connectors - Clean and repair as necessary.
You have just attempted to simulate the condition that initially set the trouble code
message.
The following additional checks may assist you in identifying a possible intermittent
problem:
- Visually inspect related wire harness connectors. Look for broken, bent, pushed out,
spread, corroded, or contaminated terminals.
- Visually inspect the related harnesses. Look for chafed, pierced, pinched or partially
broken wire.
- Refer to Wiring Diagrams and Technical Service Bulletins that may apply.
Did the DTC become active ?
All
Yes
→ Select appropriate symptom from Symptom List.
No
→ No problem found at this time. Erase all codes before returning
vehicle to customer.
132
AIRBAG
PASSENGER SQUIB 2 SHORT TO GROUND —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст