Dodge Viper SRT-10 (ZB). Manual — part 314
Symptom:
INTERNAL BCM FAILURE
When Monitored and Set Condition:
INTERNAL BCM FAILURE
When Monitored:
Continuously.
Set Condition:
The DTC will set if the BCM detects an internal fault.
POSSIBLE CAUSES
INTERNAL BCM FAILURE
TEST
ACTION
APPLICABILITY
1
Connect the DRB to the Data Link Connector.
Turn the ignition on.
With the DRB, erase BCM DTC’s.
Turn the ignition off then turn the ignition on.
With the DRB, read BCM DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Body Control Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
149
COMMUNICATION
Symptom:
MIC MESSAGES NOT RECEIVED
When Monitored and Set Condition:
MIC MESSAGES NOT RECEIVED
When Monitored:
With the ignition in the run position.
Set Condition:
The BCM does not receive any messages from the Instrument Cluster
(MIC) for at least 5 seconds.
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE MIC
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, attempt to communicate with the Instrument Cluster (MIC).
Was the DRB able to I/D or communicate with the Instrument Cluster (MIC)?
All
Yes
→ Go To 2
No
→ Refer to the Communication category for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
2
With the DRB, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
With the DRB, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Body Control Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
150
COMMUNICATION
Symptom List:
PCI BUS SHORTED TO BATTERY
PCI BUS SHORTED TO GROUND
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be PCI BUS SHORTED TO BAT-
TERY.
When Monitored and Set Condition:
PCI BUS SHORTED TO BATTERY
When Monitored:
Continuously.
Set Condition:
Anytime the BCM detects a short to battery on the PCI Bus circuit.
PCI BUS SHORTED TO GROUND
When Monitored:
Continuously.
Set Condition:
Anytime the BCM detects a short to ground on the PCI Bus circuit.
POSSIBLE CAUSES
INTERMITTENT CONDITION
TEST
ACTION
APPLICABILITY
1
NOTE: For this code to be active, the DRB will not be able to communicate
with any modules on the vehicle (except the PCM).
NOTE: Clear the code. If this code continues to set and the DRB can still
communicate with the module, it will be necessary to replace the module.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, wiggle the wiring
harnesses. This is to try and duplicate the complete bus failure condition.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
151
COMMUNICATION
Symptom:
PCI INTERNAL FAULT
When Monitored and Set Condition:
PCI INTERNAL FAULT
When Monitored:
With the ignition in the run position.
Set Condition:
The DTC will set if the BCM detects a PCI internal fault.
POSSIBLE CAUSES
PCI INTERNAL FAULT
TEST
ACTION
APPLICABILITY
1
Connect the DRB to the Data Link Connector.
Turn the ignition on.
With the DRB, erase BCM DTC’s.
Turn the ignition off then turn the ignition on.
With the DRB, read BCM DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Body Control Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
152
COMMUNICATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст