Dodge Viper SRT-10 (ZB). Manual — part 170
Bearing/Seal Remover Adapter - 8990
Puller, Slide Hammer C-3752
Crankshaft Pilot Bearing Installer 9058
Driver Handle C-4171
Front Crankshaft Seal Remover C-4679A
Front Crankshaft Seal Installer MD-998306
Rear Crankshaft Seal Installation Guide 9060
Valve Spring Compressor MD998772A
9 - 22
ENGINE
ZB
ENGINE - 8.3L (Continued)
Valve Spring Tester C-647
Pressure Tester Kit 7700
Bloc–Chek–Kit C-3685–A
Clutch Hydraulic Line Disconnect Tool 6638A
Disconnect Tool 9005
DRB III
T
with PEP Module – OT-CH6010A
Pressure Transducer OT-CH7059
Adaptor 8116
ZB
ENGINE
9 - 23
ENGINE - 8.3L (Continued)
AIR CLEANER ELEMENT
REMOVAL
The air intake system does not preheat ambient
air. The majority of the inlet air is directed into the
air cleaner front housing from the hood mounted
duct. The incoming ambient air passes through two
filter elements in the air cleaner (Fig. 15). From the
filters, ambient air passes through the throttle body
into the intake manifold.
(1) Unscrew the air cleaner cover screws (Fig. 16)
and release the top of the air cleaner assembly.
(2) Pull the air filter element up and off of the noz-
zle assembly (Fig. 17), the assembly is held in by the
lips in the housing (Fig. 18) for the filter element.
INSTALLATION
(1) Install the air filter element to the nozzle
assembly (Fig. 17), the assembly is held in place by
the lips in the housing (Fig. 18) for the filter element.
(2) Install the top of the air cleaner assembly.
(3) Install air cleaner cover screws (Fig. 16).
Fig. 15 Air Cleaner Assembly
Fig. 16 Air Cleaner Cover
Fig. 17 Air Cleaner Element
Fig. 18 Housing Lip
9 - 24
ENGINE
ZB
AIR CLEANER HOUSING
REMOVAL
The air intake system does not preheat ambient
air. The majority of the inlet air is directed into the
air cleaner front housing from the hood duct (Fig.
19). The incoming ambient air passes through two fil-
ter elements in the air cleaner. From the filters,
ambient air passes through the throttle body into the
intake manifold.
(1) Disconnect the negative battery cable.
(2) Loosen the air cleaner hose clamp at the throt-
tle body.
(3) Disconnect the idle air control hose and make
up air hose from the air cleaner assembly.
(4) Disconnect the intake air temperature sensor
electrical connector.
(5) Unscrew the rear lower fastener (Fig. 20).
(6) Remove the 2 front mounting screws (Fig. 21).
(7) Remove air cleaner assembly.
INSTALLATION
(1) Install the air cleaner assembly and hose to the
throttle body.
(2) Connect the intake air temperature sensor elec-
trical connector.
(3) Connect idle air control motor air tube to the
air cleaner.
(4) Make sure that the lower mounting stud is in
the bracket.
(5) Tighten the rear lower fastener (Fig. 20).
(6) Install the 2 front mounting screws (Fig. 21).
(7) Tighten the air cleaner hose clamp at the throt-
tle body.
(8) Connect the negative battery cable.
Fig. 19 Air Cleaner Assembly
Fig. 20 Lower Mounting Stud
Fig. 21 Front Mounting Screws
ZB
ENGINE
9 - 25
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст