Dodge Viper SRT-10 (ZB). Manual — part 304
TEST
ACTION
APPLICABILITY
3
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
Disconnect the Airbag Control Module Connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool adaptor to the Airbag Control Module connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
ON, THEN RECONNECT THE BATTERY.
Disconnect the Load Tool from the Passenger Seat Belt Tensioner connector.
Measure the voltage of the Passenger SBT Line 1 and Line 2 circuits between the
Passenger SBT connector and ground.
Is there any voltage on either circuit?
All
Yes
→ Repair the Passenger Seat Belt Tensioner Line 1 or Line 2 shorted
to battery.
Perform AIRBAG VERIFICATION TEST - VER 1.
No
→ Go To 4
4
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
If there are no possible causes remaining, view repair.
All
Repair
Replace the Airbag Control Module in accordance with the Service
information.
Perform AIRBAG VERIFICATION TEST - VER 1.
5
NOTE: Ensure the battery is fully charged.
With the DRBIII
t, record and erase all DTCs from all modules.
All active codes must be resolved before diagnosing any stored codes.
Maintain a safe distance from all airbags while performing the following steps.
With the DRBIII
t monitor active codes as you work through the system.
NOTE: If equipped with Passenger Airbag On-Off switch, read the DTC’s in
all switch positions.
Wiggle the wiring harness and connectors of the appropriate airbag system and
rotate the steering wheel from stop to stop.
NOTE: Check connectors - Clean and repair as necessary.
You have just attempted to simulate the condition that initially set the trouble code
message.
The following additional checks may assist you in identifying a possible intermittent
problem:
- Visually inspect related wire harness connectors. Look for broken, bent, pushed out,
spread, corroded, or contaminated terminals.
- Visually inspect the related harnesses. Look for chafed, pierced, pinched or partially
broken wire.
- Refer to Wiring Diagrams and Technical Service Bulletins that may apply.
Did the DTC become active ?
All
Yes
→ Select appropriate symptom from Symptom List.
No
→ No problem found at this time. Erase all codes before returning
vehicle to customer.
109
AIRBAG
PASSENGER SEAT BELT TENSIONER SHORT TO BATTERY —
Continued
Symptom:
PASSENGER SEAT BELT TENSIONER SHORT TO GROUND
When Monitored and Set Condition:
PASSENGER SEAT BELT TENSIONER SHORT TO GROUND
When Monitored:
When the ignition is on, the ACM monitors the voltage of the Passenger
Seat Belt Tensioner circuits.
Set Condition:
The ACM has detected a short to ground in the Passenger Seat Belt
Tensioner circuits.
POSSIBLE CAUSES
PAS SEAT BELT TENSIONER SHORT TO GROUND
PASSENGER SEAT BELT TENSIONER LINE 1 OR LINE 2 SHORTED TO GROUND
ACM, PASSENGER SBT SHORT TO GROUND
STORED CODE OR INTERMITTENT CONDITION
ACTIVE CODE PRESENT
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
Ensure the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ACTIVE or STORED DTC:
All
ACM - ACTIVE DTC
ACM - STORED DTC
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
2
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
Disconnect the Passenger SBT connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Passenger Seat Belt Tensioner connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t, read the active DTC’s.
Does the DRBIII
t display PASSENGER SBT SHORT TO GROUND?
All
Yes
→ Go To 3
No
→ Replace the Passenger Seat Belt Tensioner in accordance with the
Service Information.
Perform AIRBAG VERIFICATION TEST - VER 1.
110
AIRBAG
TEST
ACTION
APPLICABILITY
3
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
Disconnect the Airbag Control Module Connector
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool adaptor to the Airbag Control Module connector.
Disconnect the Load Tool from the Passenger Seat Belt Tensioner connector.
Measure the resistance of the Passenger SBT Line 1 and Line 2 circuits between the
Passenger SBT connector and ground.
Is the resistance below 10K Ohms on either circuit?
All
Yes
→ Repair the Passenger SBT Line 1 or Line 2 shorted to ground.
Perform AIRBAG VERIFICATION TEST - VER 1.
No
→ Go To 4
4
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
If there are no possible causes remaining, view repair.
All
Repair
Replace the Airbag Control Module in accordance with the Service
information.
Perform AIRBAG VERIFICATION TEST - VER 1.
5
NOTE: Ensure the battery is fully charged.
With the DRBIII
t, record and erase all DTCs from all modules.
All active codes must be resolved before diagnosing any stored codes.
Maintain a safe distance from all airbags while performing the following steps.
With the DRBIII
t monitor active codes as you work through the system.
NOTE: If equipped with Passenger Airbag On-Off switch, read the DTC’s in
all switch positions.
Wiggle the wiring harness and connectors of the appropriate airbag system and
rotate the steering wheel from stop to stop.
NOTE: Check connectors - Clean and repair as necessary.
You have just attempted to simulate the condition that initially set the trouble code
message.
The following additional checks may assist you in identifying a possible intermittent
problem:
- Visually inspect related wire harness connectors. Look for broken, bent, pushed out,
spread, corroded, or contaminated terminals.
- Visually inspect the related harnesses. Look for chafed, pierced, pinched or partially
broken wire.
- Refer to Wiring Diagrams and Technical Service Bulletins that may apply.
Did the DTC become active ?
All
Yes
→ Select appropriate symptom from Symptom List.
No
→ No problem found at this time. Erase all codes before returning
vehicle to customer.
111
AIRBAG
PASSENGER SEAT BELT TENSIONER SHORT TO GROUND —
Continued
Symptom:
PASSENGER SQUIB 1 CIRCUIT OPEN
When Monitored and Set Condition:
PASSENGER SQUIB 1 CIRCUIT OPEN
When Monitored:
When the ignition is On, the ACM monitors the resistance of the
Passenger Squib 1 circuits.
Set Condition:
The ACM has detected an open circuit or high resistance on the Passenger
Squib 1 circuits.
POSSIBLE CAUSES
PASSENGER AIRBAG OPEN
PASSENGER SQUIB 1 LINE 1 OR LINE 2 CIRCUIT OPEN
STORED CODE OR INTERMITTENT CONDITION
ACM, PASSENGER SQUIB 1 CIRCUIT OPEN
ACTIVE CODE PRESENT
TEST
ACTION
APPLICABILITY
1
NOTE: Ensure the battery is fully charged.
Turn the ignition on.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ACTIVE or STORED DTC:
All
ACM - ACTIVE DTC
ACM - STORED DTC
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
112
AIRBAG
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст