MINI Countryman (2021 year). Manual in english — page 6
CONTROLS
Driving stability control systems
may be a risk of accident or risk of damage
Automatic activation
to property. Do not deactivate DSC Dy-
When DSC is deactivated, automatic activa-
namic Stability Control when driving with
tion occurs in the following situations:
roof load.
- The vehicle has a flat tire.
- When activating cruise control in the
Indicator/warning lights
TRACTION or DSC OFF settings.
The indicator light flashes: DSC con-
trols the drive and braking forces.
DTC Dynamic Traction Con-
The indicator light lights up: DSC has
malfunctioned.
trol
Concept
Deactivating DSC: DSC OFF
DTC is a version of the DSC Dynamic Stabil-
General information
ity Control where forward momentum is op-
timized.
When DSC is deactivated, driving stability
is reduced during acceleration and when
The system ensures maximum headway on
driving in curves.
special road conditions, for instance unp-
lowed snowy roads or loose road surfaces,
To increase vehicle stability, activate DSC
but with somewhat limited vehicle stability.
again as soon as possible.
When DTC is activated, the vehicle has
Deactivating DSC
maximum traction. Driving stability is lim-
ited during acceleration and when driving
Press and hold this button but not
in curves.
longer than approx. 10 seconds, un-
Drive carefully.
til the indicator light for DSC OFF
lights up in the instrument cluster and dis-
You may find it useful to briefly activate
plays DSC OFF.
DTC under the following special circum-
stances:
DSC is switched off.
- When driving in slush or on uncleared,
snow-covered roads.
Activating DSC
- When driving off from deep snow or
Press the button.
loose ground.
DSC OFF and the DSC OFF indicator
- When driving with snow chains.
light go out.
Deactivating/activating DTC
Indicator/warning lights
Dynamic Traction Control
When DSC is deactivated, DSC OFF is dis-
played in the instrument cluster.
Activating DTC
The indicator light lights up: DSC is
Press the button.
deactivated.
176
Driving stability control systems
CONTROLS
TRACTION is displayed in the instrument
Programs
cluster and the indicator light for DSC OFF
lights up.
MID/GREEN
Balanced tuning of the shock absorbers for
Deactivating DTC
more comfort.
Press the button again.
SPORT
TRACTION and the DSC OFF indica-
Consistently sporty tuning of the shock ab-
tor light go out.
sorbers for greater driving agility.
Performance Control
MINI Driving Modes switch
Performance Control enhances the agility of
Concept
the vehicle.
The MINI Driving Modes switch helps to
To increase maneuverability, wheels are
fine-tune the vehicle's settings and features.
braked individually when a sporty driving
Choose between three different programs.
style is used.
Pressing the MINI Driving Modes switch
will activate the particular program.
ALL4
Operating the programs
ALL4 is the all-wheel-drive system of your
Switch
Program
vehicle. Concerted action by ALL4 and DSC
Dynamic Stability Control further optimizes
SPORT
traction and driving dynamics. The ALL4
MID
all-wheel-drive system variably distributes
GREEN
the driving forces to the front and rear axles
as demanded by the driving situation and
road surface.
MID
MID provides balanced tuning.
Adaptive chassis
With each starting operation, MID is acti-
vated using the Start/Stop button.
Concept
The tuning of the suspension can be
GREEN
changed with the system.
The system offers several different pro-
Concept
grams.
GREEN provides consistent tuning to maxi-
The programs are selected via the MINI
mize range.
Driving Modes switch.
177
CONTROLS
Driving stability control systems
Activating GREEN
Configuring SPORT
Press the MINI Driving Modes switch
Via the Central Information Display (CID):
downward until GREEN is displayed in the
1.
"My MINI"
instrument cluster.
2. "Vehicle settings"
Configuring GREEN
3. If necessary, "Driving mode"
4. "Configure SPORT"
Via MINI Driving Modes switch
5. Select the desired setting.
1. Activate GREEN.
This configuration is retrieved when SPORT
2. "Configure GREEN"
is activated.
3. Configure the program.
This configuration is retrieved when
Configuring driving program
GREEN is activated.
Settings can be made for the following driv-
ing programs in Driving mode:
Via the Central Information Display (CID)
- GREEN, refer to page 177.
1.
"My MINI"
- SPORT, refer to page 178.
2. "Vehicle settings"
3. If necessary, "Driving mode"
Displays
4. "Configure GREEN"
Program selection
5. Select the desired setting.
Pressing the MINI Driving
This configuration is retrieved when
Modes switch displays a list of
GREEN is activated.
programs, which can be se-
lected.
SPORT
Concept
Selected program
Consistently sporty tuning of the drivetrain
The instrument cluster dis-
for greater driving agility.
plays the selected program.
Depending on the vehicle equipment, the
tuning of the chassis and suspension also
changes and SPORT can be individually
configured.
The configuration is stored for the driver
profile currently in use.
Drive-off assistant
Activating SPORT
Concept
Press the MINI Driving Modes switch up-
ward until SPORT is displayed in the instru-
This system supports driving off on uphill
ment cluster.
grades. The parking brake is not required.
178
Driving stability control systems
CONTROLS
Driving off with the drive-off
assistant
1. Hold the vehicle in place with the foot
brake.
2. Release the foot brake and drive off
without delay.
After the foot brake is released, the vehicle
is held in place for approx. 2 seconds.
Servotronic
Servotronic is a speed-dependent power
steering function.
The system provides the steering force with
more support at low speeds than at higher
ones. This makes it easier to park, for in-
stance, and makes steering firmer when
driving at faster speeds.
Furthermore, the steering force adapts ac-
cording to the driving program, so that a
firm, sporty feel or a comfortable steering
response is conveyed.
179
CONTROLS
Driving comfort
Driving comfort
Vehicle features and options
General information
A camera on the interior mirror is used to
This chapter describes all standard, country-
detect vehicles driving ahead.
specific and optional features offered with
Depending on the settings, the characteris-
the series. It also describes features and
tics of cruise control many change in cer-
functions that are not necessarily available
tain ranges.
in your vehicle, e.g., due to the selected op-
tions or country versions. This also applies
Safety information
to safety-related functions and systems.
When using these functions and systems,
the applicable laws and regulations must be
Warning
observed.
The system cannot serve as a substitute
for the driver’s personal judgment in as-
sessing the traffic conditions. Based on
Camera-based cruise control
the limits of the system, it cannot inde-
pendently react to all traffic situations.
There is a risk of accident. Adjust driving
Concept
style to traffic conditions. Watch traffic
Using this system, a desired speed and a
closely and actively intervene where ap-
distance to a vehicle ahead can be adjusted
propriate.
using the buttons on the steering wheel.
The system maintains the desired speed on
clear roads. The vehicle accelerates or
Warning
brakes automatically.
The desired speed can be incorrectly ad-
If a vehicle is driving ahead of you, the sys-
justed or called up by mistake. There is a
tem adjusts the speed of your vehicle so
risk of accident. Adjust the desired speed
that the set distance to the vehicle ahead is
to the traffic conditions. Watch traffic
maintained. The speed is adjusted as far as
closely and actively intervene where ap-
the given situation allows.
propriate.
The distance can be adjusted in several
steps. For safety reasons, it depends on the
respective speed.
Warning
With the Stop&Go function for Steptronic
Risk of accident due to too high speed dif-
transmissions: if the vehicle ahead of you
ferences to other vehicles, for instance in
brakes to a halt, and then proceeds to drive
the following situations:
again shortly thereafter, the system is able
- When fast approaching a slowly mov-
to detect this within the given system lim-
ing vehicle.
its.
- Vehicle suddenly swerving into own
lane.
180
Driving comfort
CONTROLS
– When fast approaching standing ve-
Button Function
hicles.
Increase speed, refer to
There is a risk of injuries or danger to life.
page 182.
Watch traffic closely and actively inter-
vene where appropriate.
Reduce speed, refer to page 182.
Warning
Buttons are arranged according to vehicle's
series, optional features and country speci-
An unsecured vehicle can begin to move
fications.
and possibly roll away. There is a risk of
accident. Before exiting, secure the vehi-
Camera
cle against rolling.
In order to ensure that the vehicle is se-
cured against rolling away, follow the fol-
lowing:
- Set the parking brake.
- On uphill grades or on a downhill
slope, turn the front wheels in the di-
rection of the curb.
- On uphill grades or on a downhill
slope, also secure the vehicle, for in-
The camera is installed near the interior
stance with a wheel chock.
mirror.
Keep the windshield in front of the interior
Overview
mirror clean and clear.
Buttons on the steering wheel
Functional requirements
Button Function
Speed range
Cruise control on/off, refer to
The system is best used on well-constructed
page 182.
roads.
Store/maintain speed, refer to
The system is functional at speeds begin-
page 182.
ning at approx. 20 mph/30 km/h.
Pause cruise control, refer to
With the Stop&Go function for Steptronic
page 182.
transmissions: the system can also be acti-
vated while the vehicle is stationary.
Continue cruise control with the
last setting, refer to page 183.
The max. speed that can be set is
85 mph/140 km/h.
Reduce distance, refer to
Manual transmission: Active Cruise Control
page 183.
is interrupted below a speed of approx.
Increase the distance, refer to
20 mph/30 km/h. The system does not
page 183.
brake to a stop.
181
CONTROLS
Driving comfort
Switching on/off and interrupting
Interrupting automatically
cruise control
The system is automatically interrupted in
the following situations:
Switching on
-
When the driver applies the brakes.
Press the button on the steering
–
Manual transmission: when the clutch
wheel.
pedal is depressed for a few seconds or
released while a gear is not engaged.
Instrument cluster without enhanced
-
If selector lever position N is set.
features:
–
Dynamic Traction Control DTC is acti-
Display in the instrument cluster
vated or DSC Dynamic Stability Control
lights up.
is deactivated.
-
If DSC Dynamic Stability Control inter-
Instrument cluster without enhanced
venes.
features:
-
If the detection range of the camera is
Display in the instrument cluster
impaired, for instance by soiling, heavy
lights up. The current speed is adopted as
precipitation or glare effects from the
desired speed and displayed with symbol.
sun.
Cruise control is active and maintains the
-
Manual transmission: if the vehicle in
set speed.
front decelerates below a speed of ap-
DSC Dynamic Stability Control is switched
prox. 20 mph/30 km/h.
on, if necessary.
-
With the Stop&Go function for Step-
tronic transmissions: following a sta-
Switching off
tionary period of approx. 3 seconds, af-
With the Stop&Go function for Steptronic
ter the vehicle was braked to a stop by
transmissions: when switching off while
the system.
stationary, depress the brake pedal simulta-
neously.
Setting the speed
Press the button on the steering
Maintaining/storing the speed
wheel.
Press
or
button in the interrupted
The displays go out. The stored desired
state.
speed is deleted.
When the system is switched on, the cur-
rent speed is maintained and stored as the
Interrupting manually
desired speed.
Press the button on the steering
Instrument cluster without enhanced
wheel.
features:
With the Stop&Go function for Steptronic
The stored speed is displayed by the
transmissions: when interrupting while sta-
symbol in the Info Display of the instrument
tionary, depress the brake pedal simultane-
cluster.
ously.
DSC Dynamic Stability Control is switched
on, if necessary.
182
Driving comfort
CONTROLS
The speed can also be stored as follows:
Instrument cluster without enhanced
features:
Press the button.
The set distance is briefly displayed
in the left part of the Info Display of the in-
strument cluster.
Changing the speed
or
button: press until the desired
speed is set.
Increase the distance
If active, the displayed speed is stored and
Press the button repeatedly until
the vehicle reaches the stored speed when
the desired distance is set.
the road is clear.
Instrument cluster without enhanced
-
or
button: each time it is pressed
features:
to the point of resistance, the desired
speed increases or decreases by approx.
The set distance is briefly displayed
1 mph/1 km/h.
in the left part of the Info Display of the in-
strument cluster.
-
or
button: each time it is pressed
past the resistance point, the desired
speed changes by a maximum of 5 mph/
Continuing cruise control
10 km/h.
or
button: hold down to repeat the
General information
action.
An interrupted cruise control can be contin-
ued by calling up the stored speed.
Adjusting the distance
Make sure that the difference between cur-
rent speed and stored speed is not too large
Safety information
before calling up the stored speed. Other-
wise, unintentional braking or accelerating
Warning
may occur.
The system cannot serve as a substitute
In the following cases, the stored speed
for the driver’s personal judgment. Due to
value is deleted and cannot be called up
the system limits, braking can be late.
again:
There may be a risk of accident or risk of
- When the system is switched off.
damage to property. Be aware to the traffic
- When the ignition is switched off.
situation at all times. Adjust the distance
to the traffic and weather conditions and
Calling up the stored speed and
maintain the prescribed safety distance,
distance
possibly by braking.
Press the button with the system in-
terrupted. Cruise control is contin-
Reduce distance
ued with the stored values. The in-
strument cluster briefly displays the
Press the button repeatedly until
selected distance.
the desired distance is set.
183
CONTROLS
Driving comfort
Switching distance control on/off
- Display lights up orange: system is in-
terrupted, the display indicates the
stored speed.
Safety information
- No display: system is switched off.
Warning
If no speed is indicated, it is possible that
The system does not react to traffic driv-
the conditions necessary for operation are
ing ahead of you, but instead maintains
not currently fulfilled.
the stored speed. There may be a risk of
accident or risk of damage to property. Ad-
Distance to vehicle ahead of you
just the desired speed to the traffic condi-
tions and brake as needed.
Distance display
Distance 1
Switching distance control off
Distance control can be switched off and on
Distance 2
when driving with cruise control activated.
Press and hold this button.
Distance 3
Or:
Press and hold this button.
Distance 4
This value is set automatically af-
The indicator light in the instrument
ter the system is switched on.
cluster lights up.
Instrument clusters without enhanced fea-
To switch distance control back on, press
tures: selected distance from the vehicle
one of the two buttons again briefly.
driving ahead is briefly displayed in the left
After changing over distance control, a
hand portion of the Info Display.
Check Control message is displayed.
Detected vehicle
Displays in the instrument cluster
Instrument cluster without enhanced
features:
Desired speed and stored speed
Symbol lights up orange: a vehicle
Instrument cluster without enhanced
has been detected ahead of you.
features:
With the Stop&Go function for Step-
In addition to the indicator light, the
tronic transmissions:
desired speed is displayed in the Info Dis-
play.
Rolling bars: the detected vehicle
has driven away.
- Display lights up green: system is active,
the display indicates the desired speed.
ACC does not accelerate. To accelerate, acti-
vate ACC as follows:
184
Driving comfort
CONTROLS
– By briefly pressing the accelerator
System limits
pedal.
- By pressing the RES CNCL button.
Detection range
- By pressing the
or
button.
Indicator/warning lights
Instrument cluster without enhanced
features:
Symbol flashes orange.
The conditions are not adequate for the sys-
tem to work.
The detection capacity of the system and
The system was deactivated but applies the
the automatic braking capacity are limited.
brakes until you actively resume control by
Two-wheeled vehicles for instance might
pressing on the brake pedal or accelerator
not be detected.
pedal.
Symbol flashes red and a signal
sounds:
Deceleration
Brake and make an evasive maneu-
The system does not decelerate in the fol-
ver, if necessary.
lowing situations:
- For pedestrians, cyclists or similarly
System interrupted without detected
slow-moving road users.
vehicle.
- For red traffic lights.
- For cross traffic.
System interrupted with detected ve-
hicle.
- For oncoming traffic.
- Unlit vehicles or vehicles with nonwork-
ing lighting at night.
Displays in the Head-up Display
The information from Active Cruise Control
Swerving vehicles
can also be displayed in the Head-up Dis-
play.
A vehicle driving in front of you is not de-
tected until it is completely within the same
lane as your vehicle.
185
CONTROLS
Driving comfort
If a vehicle driving ahead of you suddenly
swerves into your lane, the system may not
be able to automatically restore the selected
distance. It may not be possible to restore
the selected distance in certain situations,
including if you are driving significantly
faster than vehicles driving ahead of you,
for instance when rapidly approaching a
truck. When a vehicle driving ahead of you
is reliably detected, the system requests
When you approach a curve the system may
that the driver intervene by braking and
briefly report vehicles in the next lane due
carrying out evasive maneuvers, if needed.
to the bend of the curve. If the system de-
celerates you may compensate it by briefly
With the Stop&Go function for
accelerating. After releasing the accelerator
Steptronic transmissions: driving off
pedal the system is reactivated and controls
speed independently.
In some situations, the vehicle cannot drive
off automatically; for example:
- On steep uphill grades.
Weather
- In front of bumps in the road.
The following restrictions can occur under
unfavorable weather or light conditions:
In these cases, press on the accelerator
pedal.
- Poorer vehicle recognition.
- Short-term interruptions for vehicles
Cornering
that are already recognized.
Examples of unfavorable weather or light
conditions:
- Wet conditions.
- Snowfall.
- Slush.
- Fog.
- Glare.
Drive attentively, and react to the current
When the desired speed is too high for a
traffic situation. If necessary, intervene ac-
curve, the speed is reduced slightly. Be-
tively, for instance by braking, steering or
cause curves may not be anticipated in ad-
evading.
vance, drive into a curve at an appropriate
speed.
Engine power
The system has a limited detection range.
The desired speed may not be maintained
Situations can arise in tight curves where a
on uphill grades if engine power is insuffi-
vehicle driving ahead will not be detected
cient.
or will be detected very late.
186
Driving comfort
CONTROLS
Malfunction
Safety information
A Check Control message is displayed if the
system fails or was automatically deacti-
Warning
vated.
The system cannot serve as a substitute
The system may not be fully functional in
for the driver’s personal judgment in as-
the following situations:
sessing the traffic conditions. Based on
- When an object was not correctly de-
the limits of the system, it cannot inde-
tected.
pendently react to all traffic situations.
There is a risk of accident. Adjust driving
- In heavy fog, wet conditions, or snow-
style to traffic conditions. Watch traffic
fall.
closely and actively intervene where ap-
- In tight curves.
propriate.
- If the field of view of the camera or the
windshield is dirty or covered.
- When driving toward bright lights.
Warning
- Up to 20 seconds after the start of the
The use of the system can lead to an in-
engine, via the Start/Stop button.
creased risk of accidents in the following
- During calibration of the camera imme-
situations, for instance:
diately after vehicle delivery.
- On winding roads.
- In heavy traffic.
- On slippery roads, in fog, snow, or
Cruise control
wet conditions, or on a loose road
surface.
Concept
There may be a risk of accident or risk of
Using this system, a desired speed can be
damage to property. Only use the system if
adjusted using the buttons on the steering
driving at constant speed is possible.
wheel. The system maintains the desired
speed. The system accelerates and brakes
automatically as needed.
Overview
General information
Buttons on the steering wheel
The system is functional at speeds begin-
Button Function
ning at approx. 20 mph/30 km/h.
Depending on the settings, the cruise con-
Cruise control on/off, refer to
trol settings many change under certain
page 188.
conditions.
Store speed, refer to page 188.
Pause cruise control, refer to
page 188.
Continue cruise control with the
last setting, refer to page 189.
187
CONTROLS
Driving comfort
Button Function
Interrupting automatically
The system is automatically interrupted in
Increase speed, refer to
the following situations:
page 188.
- When the driver applies the brakes.
Reduce speed, refer to page 188.
- If the clutch pedal is depressed for a few
seconds or released while a gear is not
engaged.
Switching on/off and interrupting
- If the gear engaged is too high for the
cruise control
current speed.
- If selector lever position N is set.
Switching on
- Dynamic Traction Control DTC is acti-
Press the button on the steering
vated or DSC Dynamic Stability Control
wheel.
is deactivated.
- If DSC Dynamic Stability Control inter-
Instrument cluster without enhanced
venes.
features:
The indicator light in the instrument
Setting the speed
cluster lights up.
Instrument cluster without enhanced
Maintaining/storing the speed
features:
Press
or
button in the interrupted
The current speed is adopted as the
state.
desired speed and is displayed with the
When the system is switched on, the cur-
symbol in the instrument cluster.
rent speed is maintained and stored as the
desired speed.
Cruise control is active and maintains the
The stored speed is displayed in the instru-
set speed.
ment cluster.
DSC Dynamic Stability Control is switched
DSC Dynamic Stability Control is switched
on, if necessary.
on, if necessary.
Switching off
The speed can also be stored as follows:
Press the button on the steering
Press the button.
wheel.
The displays go out. The stored desired
Changing the speed
speed is deleted.
or
button: press until the desired
speed is set.
Interrupting manually
If active, the displayed speed is stored and
When active, press the button on
the vehicle reaches the stored speed when
the steering wheel.
the road is clear.
-
or
button: each time it is pressed
to the point of resistance, the desired
188
Driving comfort
CONTROLS
speed increases or decreases by approx.
Desired speed and stored speed
1 mph/1 km/h.
Instrument cluster without enhanced
-
or
button: each time it is pressed
features:
past the resistance point, the desired
The desired speed is displayed to-
speed changes by a maximum of 5 mph/
gether with the symbol.
10 km/h.
- Display lights up green: system is active,
-
or
button: press button to resist-
the display indicates the desired speed.
ance point and hold. The vehicle acceler-
ates or decelerates without pressure on
- Display lights up orange: system is in-
the accelerator pedal. After the button is
terrupted, the display indicates the
released, the vehicle maintains its final
stored speed.
speed. Pressing the switch beyond the
- No display: system is switched off.
resistance point causes the vehicle to
accelerate more rapidly.
Instrument cluster without enhanced fea-
tures:
Continuing cruise control
If no speed is indicated, it is possible that
the conditions necessary for operation are
General information
not currently fulfilled.
An interrupted cruise control can be contin-
System limits
ued by calling up the stored speed.
Make sure that the difference between cur-
Engine power
rent speed and stored speed is not too large
before calling up the stored speed. Other-
The desired speed is also maintained down-
wise, unintentional braking or accelerating
hill, but may not be maintained on uphill
may occur.
grades if engine power is insufficient.
Calling up the stored speed
PDC Park Distance Control
Press the button on the steering
wheel.
Concept
The stored speed is reached again and main-
PDC is a support when parking. The system
tained.
detects objects behind the vehicle. If the ve-
hicle is equipped with front PDC, objects in
Displays in the instrument cluster
front of the vehicle are detected too. Ob-
jects that you are approaching slowly are in-
Indicator light
dicated by signal tones and a visual display.
Instrument cluster without enhanced
features:
General information
Depending on how the vehicle is
The ultrasound sensors for measuring the
equipped, the indicator light in the instru-
distances are located in the bumpers.
ment cluster indicates whether the system
The delete range, depending on obstacles
is switched on.
and environmental conditions, is approx.
6 ft/2 m.
189
CONTROLS
Driving comfort
An acoustic warning is first given in the fol-
Park assistance button
lowing situations:
- By the front middle sensors and the two
corner sensors at approx. 24 in/60 cm
Ultrasound sensors
from the object.
Ultrasound sensors of the
- By the rear middle sensors at ap-
PDC, for instance in the bump-
prox. 5 ft/1.50 m from the object.
ers.
- When a collision is imminent.
Safety information
Functional requirements
Ensure full functionality:
Warning
- Do not cover sensors, for instance with
The system cannot serve as a substitute
stickers, bicycle racks or similar.
for the driver’s personal judgment in as-
sessing the traffic conditions. There is a
- Keep the sensors clean and free of ice.
risk of accident. Adjust driving style to
traffic conditions. Watch traffic and vehi-
Switching on/off
cle surroundings closely and actively in-
tervene where appropriate.
Switching on automatically
The system switches on automatically in the
following situations:
Warning
- If selector lever position R is engaged
Due to high speeds when PDC Park Dis-
when the engine is running.
tance Control is activated, the warning can
The rearview camera also switches on.
be delayed due to physical circumstances.
- With front PDC: when obstacles are de-
There is a risk of injury or risk of damage
tected behind or in front of the vehicle
to property. Avoid approaching an object
by PDC and the speed is slower than ap-
too fast. Avoid driving off fast while PDC
prox. 2.5 mph/4 km/h.
Park Distance Control is not yet active.
With front PDC: automatic activation on ob-
stacle detection can be switched off. Via the
Overview
Central Information Display (CID):
1.
"My MINI"
With front PDC: button in vehicle
2. "Vehicle settings"
3. "Parking"
4. "Automatic PDC activation": depending
on the vehicle equipment.
5. "Automatic PDC activation"
The setting is stored for the driver pro-
file currently used.
190
Driving comfort
CONTROLS
Automatic deactivation during
Volume
forward travel
The ratio of the PDC signal tone volume to
The system switches off when a certain
the entertainment volume can be adjusted.
driving distance or speed is exceeded.
1.
"My MINI"
Switch the system back on, if needed.
2. "System settings"
With front PDC: switching on/off
3. "Tone"
manually
4. "Volume settings"
Press the park assistance button.
5. "PDC"
6. Set the desired value.
- On: the LED lights up.
The setting is stored for the driver profile
- Off: the LED goes out.
currently used.
The rearview camera image is displayed if
the reverse gear is engaged when pressing
Visual warning
the park assistance button.
The approach of the vehicle to an object can
Depending on the equipment version, the
be shown on the Control Display. Objects
system cannot be switched off manually if
that are farther away are already displayed
the reverse gear is engaged.
on the Control Display before a signal
sounds.
Warning
A display appears as soon as Park Distance
Control (PDC) is activated.
Signal tones
The range of the sensors is represented in
An intermittent tone indicates when the ve-
colors: red, green and yellow.
hicle is approaching an object. E.g., when an
When the image of the rearview camera is
object is detected to the left rear of the ve-
displayed, the switch can be made to PDC:
hicle, a signal tone sounds from the left rear
"Rear view camera"
speaker.
The shorter the distance to the object, the
System limits
shorter the intervals.
When the distance to a detected object is
Safety information
less than approx. 10 inches/25 cm, a contin-
uous tone is sounded.
Warning
With front PDC: when objects are simulta-
The system is designed to operate in cer-
neously located both in front of and behind
tain conditions and circumstances. Due to
the vehicle, an alternating continuous sig-
conditions or other factors, the system
nal is sounded.
may not respond. There may be a risk of
The signal tone is switched off, when selec-
accident or risk of damage to property. Ac-
tor lever position P is engaged on vehicles
tively intervene as warranted. Refer to the
with Steptronic transmission.
garding the scope of the system’s opera-
tion and limitations.
191
CONTROLS
Driving comfort
Limits of ultrasonic measurement
- On rough road surfaces.
The detection of objects with ultrasonic
- On uneven surfaces, such as speed
measurements can run into physical limits,
bumps.
for instance under the following conditions:
- In large buildings with right angles and
-
For small children and animals.
smooth walls, for instance in under-
ground garages.
–
For persons with certain clothing, for in-
stance coats.
- In automatic vehicle washes.
-
With external interference of the ultra-
- Due to heavy exhaust.
sound, for instance from passing vehi-
- Due to other ultrasound sources, for in-
cles or loud machines.
stance sweeping machines, high pres-
-
When sensors are dirty, iced over, dam-
sure steam cleaners or neon lights.
aged or out of position.
The malfunction is signaled by a contin-
-
If cargo protrudes.
uous tone alternating between the front
and rear speakers. As soon as the mal-
–
Under certain weather conditions such
function due to other ultrasound sources
as high relative humidity, wet condi-
is no longer present, the system is again
tions, snowfall, extreme heat, or strong
fully functional.
wind.
With front PDC: to reduce false alarms,
-
With tow bars and trailer couplings of
switch off automatic PDC activation on ob-
other vehicles.
stacle detection, for instance in vehicle
-
With thin or wedge-shaped objects.
washes; see Switching on/off.
–
With moving objects.
–
With elevated, protruding objects such
Malfunction
as ledges or cargo.
A Check Control message is displayed in the
-
With objects with corners and sharp
instrument cluster.
edges.
Red symbol is displayed, and the
-
With objects with a fine surface struc-
range of the sensors is dimmed on
ture such as fences.
the Control Display.
-
For objects with porous surfaces.
PDC has failed. Have the system checked by
–
Low objects already displayed, for in-
a dealer's service center or another qualified
stance curbs, can move into the blind
service center or repair shop.
area of the sensors before or after a con-
tinuous tone sounds.
Rearview camera
False warnings
The system may issue a warning under the
Concept
following conditions even though there is
no obstacle within the detection range:
The rearview camera provides assistance in
parking and maneuvering backwards. The
- In heavy rain.
area behind the vehicle is shown on the
- When sensors are very dirty or covered
Control Display.
with ice.
- When sensors are covered in snow.
192
Driving comfort
CONTROLS
Safety information
Switching on/off
Switching on automatically
Warning
The system is switched on automatically if
The system cannot serve as a substitute
selector lever position R is engaged when
for the driver’s personal judgment in as-
the engine is running.
sessing the traffic conditions. There is a
risk of accident. Adjust driving style to
Automatic deactivation during
traffic conditions. Watch traffic and vehi-
forward travel
cle surroundings closely and actively in-
tervene where appropriate.
The system switches off when a certain
driving distance or speed is exceeded.
Switch the system back on, if needed.
Overview
Depending on the vehicle equipment:
Depending on the vehicle equipment:
switching on/off manually
button in the vehicle
Press the park assistance button.
- On: the LED lights up.
- Off: the LED goes out.
The parking assistance functions are shown
on the Control Display.
Switching the view via the Central
Information Display (CID)
Park assistance button
If the rearview camera view is not dis-
played, change the view via the Central In-
formation Display (CID):
Camera
"Rear view camera"
The rearview camera image is displayed.
Display on the Control Display
Functional requirements
- The rearview camera is switched on.
- The tailgate is fully closed.
- Keep the recording range of the camera
clear.
The camera lens is located in the handle of
Protruding cargo or carrier systems and
the tailgate.
trailers that are not connected to a
The image quality may be impaired by dirt.
trailer power socket can lead to malfunc-
If necessary, clean the camera lens.
tions.
193
CONTROLS
Driving comfort
Activating assistance functions
Turning radius lines
More than one assistance function can be
active at the same time.
- Parking aid lines
"Parking aid lines"
Lanes and turning radius lines are indi-
cated.
- Obstacle marking
"Obstacle marking"
Obstacles are marked, depending on the
Turning radius lines can be superimposed
vehicle equipment.
on the image of the rearview camera.
Turning radius lines show the course of the
Pathway lines
smallest possible turning radius on a level
road.
Only one turning radius line is displayed af-
ter the steering wheel is turned past a cer-
tain angle.
Obstacle marking
Pathway lines can be superimposed on the
image of the rearview camera.
Pathway lines help you to estimate the
space required when parking and maneu-
vering on level roads.
Pathway lines depend on the current steer-
ing angle and are continuously adjusted to
Depending on the vehicle equipment, obsta-
the steering wheel movements.
cle markings can be faded into the image of
the rearview camera.
The colored thresholds of the obstacle mark-
ings match the markings of the PDC Park
Distance Control.
194
Driving comfort
CONTROLS
Parking using pathway and turning
System limits
radius lines
Detection of objects
1. Position the vehicle so that the turning
radius lines lead to within the limits of
Very low obstacles or high, protruding ob-
the parking space.
jects such as ledges may not be recognized
by the system.
Depending on the vehicle equipment, some
assistance functions also consider data from
the PDC Park Distance Control.
Follow the notes in the PDC Park Distance
Control chapter.
The objects displayed on the Control Dis-
play may be closer than they appear. There-
fore, do not estimate the distance from the
objects on the display.
2. Turn the steering wheel to the point
where the pathway line covers the cor-
responding turning radius line.
Parking assistant
Concept
Display settings
Brightness
This system assists the driver in parking
With the rearview camera switched on:
parallel to the road.
1.
Select the symbol.
General information
2. Turn the Controller until the desired set-
Parking assistant handling is divided into
ting is reached and press the Controller.
three steps:
- Switching on and activating.
Contrast
- Parking space search.
With the rearview camera switched on:
- Parking.
1.
Select the symbol.
Ultrasound sensors measure parking spaces
2. Turn the Controller until the desired set-
on both sides of the vehicle.
ting is reached and press the Controller.
195
CONTROLS
Driving comfort
The parking assistant calculates the best
Overview
possible parking line and takes control of
steering during the parking procedure.
Button in the vehicle
System status and instructions on required
actions are displayed on the Control Dis-
play.
A component of the parking assistant is the
PDC Park Distance Control.
Safety information
Warning
The system cannot serve as a substitute
Park assistance button
for the driver’s personal judgment in as-
sessing the traffic conditions. Based on
the limits of the system, it cannot inde-
Ultrasound sensors
pendently react to all traffic situations.
There is a risk of accident. Adjust driving
style to traffic conditions. Watch traffic
closely and actively intervene where ap-
propriate.
NOTICE
The parking assistant can steer the vehicle
over or onto curbs. There is a risk of dam-
The ultrasound sensors for measuring park-
age to property. Watch traffic closely and
ing spaces are located on the wheel hous-
actively intervene where appropriate.
ing.
The safety information of the PDC Park Dis-
tance Control applies in addition.
Functional requirements
Ultrasound sensors
Ensure full functionality:
- Do not cover sensors, for instance with
stickers.
- Keep the sensors clean and unob-
structed.
For measuring parking spaces
- Maximum speed while driving forward
approx. 22 mph/35 km/h.
196
Driving comfort
CONTROLS
– Maximum distance to row of parked ve-
Display on the Control Display
hicles: 5 ft/1.5 m.
System activated/deactivated
Suitable parking space
- Gaps behind an object that has a min.
Symbol Meaning
length of 5 ft/1.5 m.
Gray: the system is not availa-
- Gap between two objects with a mini-
ble.
mum length of approx. 5 ft/1.5 m.
White: the system is available
- Min. length of gap between two objects:
but not activated.
your vehicle's length plus approx.
The system is activated.
3.3 ft/1.0 m.
- Minimum depth: approx. 5 ft/1.5 m.
Parking space search and system
For parking
status
- Doors and tailgate are closed.
- The parking brake is released.
- When parking in parking spaces on the
driver's side, the corresponding turn sig-
nal must be switched on.
Switching on and activating
Switching on with the button
-
Symbol P on the vehicle image: the park-
Press the park assistance button.
ing assistant is activated and the park-
The LED lights up.
ing space search is active.
-
Control Display shows suitable parking
The current status of the parking space
spaces at the edge of the road next to
search is indicated on the Control Display.
the vehicle symbol. When the parking
Parking assistant is activated automati-
assistant is active, suitable parking
cally.
spaces are highlighted.
-
The parking procedure is
Switching on with reverse gear
active. The system takes
Shift into reverse.
over the steering.
The current status of the parking space
search is indicated on the Control Display.
To activate:
"Parking Assistant"
-
Parking space search is always active
whenever the vehicle is moving forward
slow and straight, even if the system is
deactivated. When the system is deacti-
vated, the displays on the Control Dis-
play are shown in gray.
197
CONTROLS
Driving comfort
Parking using the parking assistant
- If the vehicle speed exceeds approx.
6 mph/10 km/h.
Parking
- Possibly on snow-covered or slippery
road surfaces.
1.
Press the park assistance button or
- If a maximum number of parking at-
shift into reverse gear to switch on the
tempts or the time taken for parking is
parking assistant, refer to page 197. Ac-
exceeded.
tivate the parking assistant, if needed.
- If the PDC Park Distance Control dis-
Parking assistant is activated.
plays clearances that are too small.
2.
Pass the row of parked vehicles at a
- When switching into other functions of
speed of up to approx. 22 mph/35 km/h
the radio.
and at a distance of maximum
A Check Control message is displayed.
5 ft/1.5 m.
The status of the parking space search
Resuming
and possible parking spaces are dis-
An interrupted parking procedure can be
played on the display, refer to page 197.
continued, if needed.
3.
Follow the instructions on the display.
Reactivate the parking assistant, refer to
The best possible parking position will
page 197, and follow the instructions on the
come after gear change on the station-
display.
ary vehicle - wait for the automatic
steering wheel move.
Switching off
The end of the parking procedure is in-
The system can be switched off as follows:
dicated on the display.
-
Press the park assistance button.
4.
Adjust the parking position yourself, if
needed.
- Switching off the ignition.
Interrupting manually
System limits
The parking assistant can be interrupted at
any time:
Safety information
-
Press the park assistance button.
Warning
–
"Parking Assistant"
The system is designed to operate in cer-
Interrupting automatically
tain conditions and circumstances. Due to
conditions or other factors, the system
The system is interrupted automatically in
may not respond. There may be a risk of
the following situations:
accident or risk of damage to property. Ac-
- If the driver grasps the steering wheel
tively intervene as warranted. Refer to the
or takes over steering.
- If a gear is selected that does not match
garding the scope of the system’s opera-
the instruction on the display.
tion and limitations.
198
Driving comfort
CONTROLS
No parking assistance
- With objects with corners and sharp
edges.
The parking assistant does not offer assis-
tance in the following situations:
- With objects with a fine surface struc-
ture such as fences.
- In tight curves.
- For objects with porous surfaces.
Functional limitations
- Low objects already displayed, for in-
The system may not be fully functional in
stance curbs, can move into the blind
the following situations:
area of the sensors before or after a con-
tinuous tone sounds.
- On bumpy road surfaces such as gravel
roads.
- The parking assistant may identify park-
ing spaces that are not suitable for park-
- On slippery ground.
ing.
- With accumulations of leaves/snow in
the parking space.
Tire size
- With a mounted emergency wheel.
The parking position may vary depending
- With ditches or edges, for instance an
on the tire size.
edge of a port.
Malfunction
Limits of ultrasonic measurement
A Check Control message is displayed.
The detection of objects with ultrasonic
The parking assistant failed. Have the sys-
measurements can run into physical limits,
tem checked by a dealer's service center or
for instance under the following conditions:
another qualified service center or repair
-
For small children and animals.
shop.
–
For persons with certain clothing, for in-
stance coats.
-
With external interference of the ultra-
sound, for instance from passing vehi-
cles or loud machines.
-
When sensors are dirty, iced over, dam-
aged or out of position.
-
If cargo protrudes.
–
Under certain weather conditions such
as high relative humidity, wet condi-
tions, snowfall, extreme heat, or strong
wind.
-
With tow bars and trailer couplings of
other vehicles.
-
With thin or wedge-shaped objects.
–
With moving objects.
–
With elevated, protruding objects such
as ledges or cargo.
199
CONTROLS
Climate control
Climate control
- Emission tested passenger compart-
Vehicle features and options
ment.
- Microfilter.
This chapter describes all standard, country-
specific and optional features offered with
- Air conditioning system to control the
the series. It also describes features and
temperature, air flow and recirculated-
functions that are not necessarily available
air mode.
in your vehicle, e.g., due to the selected op-
Depending on the equipment specification:
tions or country versions. This also applies
- Microfilter/activated-charcoal filter.
to safety-related functions and systems.
- Automatic climate control.
When using these functions and systems,
the applicable laws and regulations must be
- Parked-car ventilation.
observed.
Interior air quality
The air quality in the vehicle is improved by
the following components:
200
Climate control
CONTROLS
Air conditioner
1
Air distribution settings
6
Recirculated-air mode
2
Air flow
7
Rear window defroster
3
Temperature
8
Windshield defroster
4
Seat heating, right
87
9
Seat heating, left
87
5
Air conditioning
Climate control functions in detail
Temperature
Switching the system on/off
Concept
The system heats or cools, depending on the
Switching on
set temperature.
Set any air flow.
Adjusting
Switching off
Turn the wheel to set the de-
Turn the wheel for air flow all
sired temperature.
the way to the left.
201
CONTROLS
Climate control
Air conditioning
With constant recirculated-air mode, the air
quality in the car's interior deteriorates and
Concept
window fogging increases.
The air in the car's interior will be cooled
If the windows fog over, switch off recircu-
and dehumidified and, depending on the
lated-air mode and increase the air flow, if
temperature setting, warmed again.
needed.
The car's interior can only be cooled with
Controlling the air flow manually
the engine running.
Concept
Switching on/off
The air flow for climate control can be ad-
Press the button.
justed manually.
The LED is illuminated with air con-
ditioning switched on.
Operation
Depending on the weather, the windshield
Turn the ring to set the de-
may fog up briefly when the engine is
sired air flow.
started.
The higher the air flow, the
The air conditioner produces condensation
more effective the heating or
water, refer to page 235, that will exit from
cooling will be.
below the vehicle.
The air flow from the air conditioner may be
reduced automatically to save battery
Recirculated-air mode
power.
Concept
Controlling the air distribution
You may react to unpleasant odors or pollu-
manually
tants in the immediate environment by tem-
porarily suspending the supply of outside
Concept
air. The system then recirculates the air
flow within the vehicle.
The air distribution for climate control can
be adjusted manually.
Operation
Operation
Press the button:
Turn the wheel to select the
The LED is illuminated when recir-
desired program or the desired
culated-air mode is switched on. The supply
intermediate setting.
of outside air is shut off.
When recirculated-air mode is switched off,
fresh air is directed into the vehicle's inte-
-
Windows.
rior.
-
Upper body region.
To prevent window condensation, recircu-
–
Floor area.
lated-air mode switches off automatically af-
ter a certain amount of time, depending on
–
Windows, upper body region, and
the external temperature.
floor area.
202
Climate control
CONTROLS
To defrost windows and remove
For permanent activation, press the button
condensation
for longer than 3 seconds. To deactivate,
press the button again.
Make the following settings to defrost the
windows and remove condensation:
The rear window defroster can only be acti-
vated continuously at an external tempera-
- Direct the air distribution onto the win-
ture below approx. 41 ℉/5 ℃.
dows.
- Increasing the air flow.
When GREEN Mode is activated, the heat-
ing output is reduced.
- Increase the temperature.
- Switch on the air conditioning if needed.
Microfilter
In external and recirculated-air mode, the
Windshield defroster
microfilter filters dust and pollen from the
Press the button. The LED lights up.
air.
The front window defroster
Have this filter changed during vehicle
switches off automatically after a certain
maintenance, refer to page 278.
period of time.
Rear window defroster
Press the button. The LED lights up.
The rear window defroster switches
off automatically after a certain period of
time.
203
CONTROLS
Climate control
Automatic climate control
1
Temperature, left
9
Maximum cooling
2
Display
10 Air conditioning
3
Air flow, AUTO intensity
11 Recirculated-air mode
4
AUTO program
12 Rear window defroster
5
Air distribution, manual
13 Windshield defroster
6
Display
14 To defrost windows and remove conden-
sation
7
Temperature, right
15 Seat heating, left
87
8
Seat heating, right
87
Climate control functions in detail
Switching off
Turn wheel for air flow to the
Switching the system on/off
left until the control switches
off.
Switching on
Set any air flow.
Temperature
Concept
The automatic climate control achieves the
set temperature as quickly as possible, if
204
Climate control
CONTROLS
necessary by using the maximum cooling or
Maximum cooling
heating power, and then keeps it constant.
Concept
Adjusting
The system is set to the lowest temperature,
Turn the wheel to set the de-
maximum air flow and recirculated-air
sired temperature.
mode.
General information
The function is available with external tem-
peratures beyond approx. 32 ℉/0 ℃ and
Do not rapidly switch between different
with the engine running.
temperature settings. The automatic climate
control will not have sufficient time to ad-
Air flows out of the vents to the upper body
just the set temperature.
region. The vents need to be open for this.
The air flow can be adjusted with the pro-
Air conditioning
gram active.
Concept
Switching on/off
The air in the car's interior will be cooled
Press the button.
and dehumidified and, depending on the
The LED is illuminated with the
temperature setting, warmed again.
system switched on.
The car's interior can only be cooled with
the engine running.
AUTO program
Switching on/off
Concept
Press the button.
The AUTO program cools, ventilates or
The LED is illuminated with air con-
heats the car's interior automatically.
ditioning switched on.
The air distribution and temperature are
Depending on the weather, the windshield
controlled automatically depending on the
may fog up briefly when the engine is
temperature in the car's interior and the de-
started.
sired temperature setting including the se-
lected intensity of the air flow.
The cooling function is switched on auto-
matically with the AUTO program.
Switching on/off
When using the automatic climate control,
condensation water, refer to page 235, de-
Press the button.
velops and drains underneath the vehicle.
The LED is illuminated with the
This is normal.
AUTO program switched on.
Depending on the selected temperature,
AUTO intensity and outside influences, the
air is directed to the windshield, side win-
dows, upper body, and into the floor area.
205
CONTROLS
Climate control
Point the side vents toward the side win-
Switching on/off
dows.
Press button repeatedly to select an
The following features are switched on au-
operating mode:
tomatically with the AUTO program:
- LEDs off: outside air flows in continu-
- The air conditioning, refer to page 205.
ously.
To switch off the program: press the button
- Left LED on, automatic recirculated-air
again or manually adjust the air distribu-
control: a sensor detects pollutants in
tion.
the outside air and shuts off automati-
cally.
Intensity
- Right LED on, recirculated-air mode: the
With the AUTO program activated, the au-
supply of outside air into the vehicle is
tomatic intensity control can be changed.
permanently blocked.
Turn the ring to set the de-
To prevent window condensation, recircu-
sired intensity from soft to in-
lated-air mode switches off automatically af-
tensive.
ter a certain amount of time, depending on
the external temperature.
If windows are fogged over, switch off the
The set intensity is displayed via the posi-
recirculating mode and press the AUTO but-
tion of the illuminated LED segment.
ton. Make sure that air can flow to the
windshield.
Automatic recirculated-air control/
recirculated-air mode
Adjusting the air flow manually
Concept
Concept
The automatic recirculated-air control AUC
The air flow for climate control can be ad-
recognizes odors or pollutants in the out-
justed manually.
side air. The outside air supply is shut off
and the interior air is recirculated.
General information
To adjust the air flow manually switch off
General information
AUTO program first.
If the system is activated, a sensor detects
pollutants in the outside air and controls the
Operation
shut-off automatically.
Turn the ring to set the de-
If the system is deactivated, outside air con-
sired air flow.
tinuously flows into the car's interior.
With constant recirculated-air mode, the air
quality in the car's interior deteriorates and
window fogging increases.
The manually adjusted air flow is displayed
You may react to unpleasant odors or pollu-
via illuminated LED segments.
tants in the immediate environment by tem-
The air flow of the automatic climate con-
porarily suspending the supply of outside
trol may be reduced automatically to save
air. The system then recirculates the air
battery power.
flow within the vehicle.
206
Climate control
CONTROLS
Adjusting the air distribution
The front window defroster switches off au-
manually
tomatically after a certain period of time.
Concept
Rear window defroster
The air distribution for climate control can
Press the button. The LED lights up.
be adjusted manually.
The rear window defroster switches
Operation
off automatically after a certain period of
time.
Press the button repeatedly to se-
For permanent activation, press the button
lect a program:
for longer than 3 seconds. To deactivate,
- Windows, upper body region, and floor
press the button again.
area.
The rear window defroster can only be acti-
- Upper body region and floor area.
vated continuously at an external tempera-
ture below approx. 41 ℉/5 ℃.
- Floor area.
- Windows and floor area.
When GREEN Mode is activated, the heat-
- Windows.
ing output is reduced.
- Windows and upper body region.
Microfilter/activated-charcoal filter
- Upper body region.
In external and recirculated-air mode, the
microfilter/activated charcoal filter filters
To defrost windows and remove
dust, pollen, and gaseous pollutants out of
condensation
the air.
Have this filter changed during vehicle
Concept
maintenance, refer to page 278.
Ice and condensation are quickly removed
from the windshield and the front side win-
dows.
Ventilation
Switching on/off
Setting
Press the button.
The air flow directions can be individually
The LED is illuminated with the
adjusted:
system switched on.
- Direct ventilation:
The air flow can be adjusted with the pro-
The air flow is directly pointed onto the
gram active.
person. The air flow heats or cools no-
If there is window condensation, switch on
ticeably, depending on the adjusted tem-
the air conditioning too.
perature.
- Indirect ventilation:
Windshield defroster
If the vents are fully or partly closed, the
Press the button. The LED lights up.
air is directly routed into the car's inte-
rior.
207
CONTROLS
Climate control
Front ventilation
activation times. The system remains
switched on for 30 minutes.
The parked-car ventilation system is oper-
ated via the Central Information Display
(CID).
Functional requirements
- Direct operation: vehicle is in radio-
ready state.
- Direct operation or preset activation
- Turn knob for continuous opening and
time: does not depend on external tem-
closing of the vents.
perature.
- Swivel the vents to alter the direction of
- Battery is sufficiently charged.
the vent flow, arrows.
If parked-car ventilation is switched on,
the vehicle battery will be discharged.
Thus, limit the maximum activation time
Ventilation in the rear
to save the vehicle battery. The system
will be available again after the engine
is started or after a short trip.
- Make sure that the vehicle's date and
time are set correctly.
- Open the vents to allow air to flow out.
Switching on/off directly
Via the Central Information Display (CID):
- Lever for changing the air flow direc-
1.
"My MINI"
tion, arrow 1.
2. "Vehicle settings"
- Thumbwheel for variable opening and
3. If necessary, "Climate functions"
closing of the vents, arrow 2.
4. "Activate comfort ventilation now"
The symbol on the automatic climate
control flashes if the system is switched on.
Parked-car ventilation
Preselecting the activation time
Concept
Via the Central Information Display (CID):
The parked-car ventilation ventilates the
car's interior and lowers its temperature, if
1.
"My MINI"
needed.
2. "Vehicle settings"
3. If necessary, "Climate functions"
General information
4. "Comfort ventilation"
The parked-car ventilation can be switched
on and off directly or by using two preset
208
Climate control
CONTROLS
5. Select the desired activation time.
6. Set the desired time.
Activating the activation time
Via the Central Information Display (CID):
1.
"My MINI"
2. "Vehicle settings"
3. If necessary, "Climate functions"
4. "For start time at:"
Activate the desired activation time.
The symbol on the automatic climate
control lights up when the activation time is
activated.
The symbol on the automatic climate
control flashes when the system has been
switched on.
The system will only be switched on within
the next 24 hours. After that, it needs to be
reactivated.
209
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст