MINI Countryman (2021 year). Manual in english — page 9
MOBILITY
Maintenance
Maintenance
Vehicle features and options
General information
Information on service notifications, refer
This chapter describes all standard, country-
to page 134, can be displayed on the Control
specific and optional features offered with
Display.
the series. It also describes features and
functions that are not necessarily available
Service data in the vehicle key
in your vehicle, e.g., due to the selected op-
Information on the service notifications is
tions or country versions. This also applies
continuously stored in the vehicle key. The
to safety-related functions and systems.
service center can read this data out and
When using these functions and systems,
suggest a maintenance scope for the vehi-
the applicable laws and regulations must be
cle.
observed.
Therefore, hand the service advisor the ve-
hicle key with which the vehicle was driven
most recently.
MINI maintenance system
Storage periods
The maintenance system provides service
Storage periods during which the vehicle
notifications and thereby provides support
battery was disconnected are not taken into
in maintaining road safety and the opera-
account.
tional reliability of the vehicle.
If this occurs, have a dealer's service center
In some cases, scopes and intervals of the
or another qualified service center or repair
maintenance system may vary according to
shop update the time-dependent mainte-
the country version. Replacement work,
nance procedures, such as checking brake
spare parts, fuels and lubricants, and wear
fluid and, if necessary, changing the engine
materials are calculated separately. Further
oil and the microfilter/activated-charcoal
information is available from a dealer's serv-
filter.
ice center or another qualified service cen-
ter or repair shop.
Maintenance Manual and
Condition Based Service CBS
Service and Warranty Infor-
mation Booklet for US models
Concept
and Warranty and Service
Sensors and special algorithms take into ac-
Guide Booklet for Canadian
count the driving conditions of the vehicle.
models
CBS uses these to calculate the need for
maintenance.
Please consult your Maintenance Manual
The system makes it possible to adapt the
and Service and Warranty Information
amount of maintenance corresponding to
Booklet for US models and Warranty and
your user profile.
278
Maintenance
MOBILITY
Service Guide Booklet for Canadian models
Position
for additional information on the perform-
ance of service and maintenance work.
The manufacturer of your vehicle recom-
mends that maintenance and repair be per-
formed by a service center or another quali-
fied service center or repair shop. Records
of regular maintenance and repair work
should be retained.
There is an OBD socket on the driver's side
Socket for OBD Onboard Diag-
for checking the primary components in the
nosis
vehicle's emissions.
General information
Emissions
Devices connected to the OBD socket trig-
- The warning light lights up:
ger the alarm system when the vehicle is
locked. Remove any devices connected at
Emissions are deteriorating.
the OBD socket before locking the vehicle.
Have the vehicle checked as soon
as possible.
Safety information
-
The warning light flashes under certain
circumstances:
This indicates that there is excessive
NOTICE
misfiring in the engine.
The socket for Onboard Diagnosis is an in-
Reduce the vehicle speed and have the
tricate component intended to be used in
system checked immediately; otherwise,
conjunction with specialized equipment to
serious engine misfiring within a brief
check the vehicle’s primary emissions sys-
period can seriously damage emission
tem. Improper use of the socket for On-
control components, in particular the
board Diagnosis, or contact with the
catalytic converter.
socket for Onboard Diagnosis for other
than its intended purpose, can cause vehi-
cle malfunctions and creates risks of per-
sonal and property damage. Given the fore-
going, the manufacture of your vehicle
strongly recommends that access to the
socket for Onboard Diagnosis be limited to
a dealer's service center or another quali-
fied service center or repair shop or other
persons that have the specialized training
and equipment for purposes of properly
utilizing the socket for Onboard Diagnosis.
279
MOBILITY
Replacing components
Replacing components
Vehicle features and options
Wiper blades
This chapter describes all standard, country-
Safety information
specific and optional features offered with
the series. It also describes features and
NOTICE
functions that are not necessarily available
in your vehicle, e.g., due to the selected op-
The window may sustain damage if the
tions or country versions. This also applies
wiper falls onto it without the wiper blade
to safety-related functions and systems.
installed. There is a risk of damage to
When using these functions and systems,
property. Hold the wiper firmly when
the applicable laws and regulations must be
changing the wiper blade. Do not fold or
observed.
switch on the wiper without a wiper blade
installed.
Vehicle tool kit
NOTICE
Folded-away wipers can be jammed when
the hood is opened. There is a risk of dam-
age to property. Make sure that the wipers
with the wiper blades mounted are folded
down onto the windshield before opening
the hood.
Replacing the front wiper blades
The bag containing the onboard vehicle tool
1. To change the wiper blades, fold up the
kit is located beneath the cargo floor panel.
wiper arms.
2. Fold up and hold the wiper arm firmly.
After use, secure the bag with the onboard
vehicle tool kit on a lashing eye again.
3. Press the button, arrow 1, and swing out
the wiper blade, arrow 2.
280
Replacing components
MOBILITY
4. Attach a new wiper blade. The wiper
Light-emitting diodes (LEDs)
blade must engage audibly.
Some items of equipment use light-emitting
5. Fold down the wiper arm.
diodes installed behind a cover as a light
source. These light-emitting diodes are re-
Rear wiper blade
lated to conventional lasers and are offi-
cially designated as Class 1 light-emitting
1. Fold up and hold the wiper arm firmly.
diodes.
2. Pull the wiper blade out of the wiper
Follow the safety information, refer to
arm.
page 281.
Safety information
Lights and bulbs
Warning
Bulbs can get hot during operation. Con-
tact with the bulbs can cause burns. There
is a risk of injury. Only change bulbs after
3. Attach a new wiper blade. The wiper
they have cooled off.
blade must engage audibly.
4. Fold down the wiper arm.
Warning
Work on switched-on lighting systems can
Light and bulb replacement
cause short circuits. There is a risk of in-
jury or risk of damage to property. When
General information
working on the lighting system, switch off
the lights in question. If necessary, heed
Lights and bulbs
the bulb manufacturer's instructions.
Lights and bulbs make an essential contri-
bution to vehicle safety.
NOTICE
The manufacturer of the vehicle recom-
mends that you have appropriate work per-
Dirty bulbs have a reduced service life.
formed by a dealer’s service center or an-
There is a risk of damage to property. Do
other qualified service center or repair shop
not hold new bulbs with your bare hands.
if you are unfamiliar with it or if it has not
Use a clean cloth or something similar, or
been described here.
hold the bulb by its base.
A spare light box is available from a dealer's
service center or another qualified service
center or repair shop.
Follow the safety information, refer to
page 281.
281
MOBILITY
Replacing components
Light-emitting diodes (LEDs)
Front halogen lights, bulb
replacement
Warning
Overview
Intensive brightness can irritate or dam-
age the retina of the eye. There is a risk of
Halogen headlights
injury. Do not look directly into the head-
lights or other light sources. Do not re-
move the LED covers.
Headlight glass
Condensation can form on the inside of the
headlight glass in cool or humid weather.
When driving with the lights switched on,
the condensation evaporates after a short
time. The headlight glass does not need to
1
High beams
be changed.
2
Low beams
If despite driving with the headlights
3
Turn signal
switched on, increasing humidity forms, for
instance water droplets in the light, have
the headlights checked.
High beams
Follow the general instructions on lights
Headlight setting
and bulbs, refer to page 281.
The headlight adjustments can be affected
55-watt bulb, H7.
by changing lights and bulbs. After the
headlight adjustment was changed, have it
1. Open the hood, refer to page 270.
checked and, if necessary, corrected by a
2. Turn the lid counterclockwise and re-
dealer’s service center or another qualified
move.
service center or repair shop.
282
Replacing components
MOBILITY
3. Tilt the bulb holder up, arrow 1, and pull
- On the right facing the driving direc-
it out of the headlight toward the rear,
tion: turn the cover counterclock-
arrow 2.
wise and remove it.
4. Pull the bulb out of the bulb holder.
3.
Unscrew the inner cover counterclock-
wise, and remove it.
5. Install the new bulb with the bulb
holder in reverse order of removal. In
doing so, ensure that the bulb tab is cor-
rectly positioned in the headlight hous-
ing and the bulb holder perceptibly en-
gages.
6. Check the position of the bulb through
the headlight glass.
7. Close the headlight housing with the lid.
Make sure that the lid engages.
4.
Tilt the bulb holder down, arrow 1, and
Low beams
pull it downward out of the headlight,
arrow 2.
Follow the general instructions on lights
and bulbs, refer to page 281.
55-watt bulb, H7.
1. Turn the steering wheel.
2.
- On the left facing the driving direc-
tion: turn the cover clockwise and
remove it.
5. Pull the bulb out of the bulb holder.
6. Install the new bulb with the bulb
holder in reverse order of removal. In
doing so, ensure that the bulb tab is cor-
rectly positioned in the headlight hous-
ing and the bulb holder perceptibly en-
gages.
283
MOBILITY
Replacing components
7. Check the position of the bulb through
4. Turn the bulb holder counterclockwise,
the headlight glass.
arrow 1, and remove, arrow 2.
8. Install the covers. Make sure that the
covers engage.
Turn signal
Follow the general instructions on lights
and bulbs, refer to page 281.
24-watt bulb, PWY24W.
1.
Turn the steering wheel.
2.
- On the left facing the driving direc-
5. Press the bulb gently into the bulb
tion: turn the cover clockwise and
holder, turn counterclockwise and re-
remove it.
move.
- On the right facing the driving direc-
6. Insert the new bulb and install the cov-
tion: turn the cover counterclock-
ers in the reverse order. Make sure that
wise and remove it.
the covers engage.
LED front lights, bulb replacement
General information
The following lights feature LED technol-
ogy:
- Daytime running lights
- High beams
- Low beams
3.
Unscrew the inner cover counterclock-
wise, and remove it.
- Cornering light
- Parking lights
- Fog lights
In the case of a malfunction, contact a deal-
er's service center or another qualified serv-
ice center or repair shop.
284
Replacing components
MOBILITY
Overview
24-watt bulb, PWY24W.
1. Open the hood, refer to page 270.
Position of the headlights
2. Turn the lid counterclockwise and re-
move.
1
Turn signal
2
Daytime running lights
3. Turn the bulb holder counterclockwise,
3
Low beams/high beams
arrow 1, and remove, arrow 2.
4
Cornering light
LED bug light
4. Press the bulb gently into the bulb
holder, turn counterclockwise and re-
move.
1
Parking lights
5. Insert the new bulb and install the cover
in the reverse order.
2
Fog lights
LED front fog lights
Turn signal
These front fog lights are made using LED
Follow the general instructions on lights
technology. In the case of a malfunction,
and bulbs, refer to page 281.
contact a dealer's service center or another
qualified service center or repair shop.
285
MOBILITY
Replacing components
Tail lights, bulb replacement
Side LED tail lights
Overview
1
Brake light
2
Tail lights
1
Side tail lights
3
Turn signal
2
Center brake light
4
Reversing lights
3
License plate light
Side tail lights
Side tail lights
Follow the general instructions on lights
and bulbs, refer to page 281.
- Bulb, brake lights/rear lights, tail lights:
P21W.
- Bulb, brake lights/LED tail lights:
H21W.
- Bulb, turn signals: P21W.
- Bulb, reversing lights: P21W.
1. Open the tailgate.
1
Brake lights/tail lights
2. Remove left or right cover.
2
Turn signal
3
Reversing lights
3. Through the opening, loosen the plug
connector, arrow 2 on the bulb holder.
286
Replacing components
MOBILITY
Press the latches together, arrows 1, and
Side turn signal, bulb replacement
remove the bulb holder.
Follow the general instructions on lights
and bulbs, refer to page 281.
Bulb: WY5W.
1. Push the side turn signal forward in the
driving direction, arrow 1, and swing it
outward, arrow 2.
4. Remove the bulb holder from the open-
ing.
5. Press the nonworking bulb gently into
the socket, turn counterclockwise and
remove.
- Arrow 1: brake lights/tail lights
2.
- On the left facing the driving direc-
- Arrow 2: turn signal
tion: turn the bulb holder clockwise
- Arrow 3: reversing light
and remove.
- On the right facing the driving direc-
tion: turn the bulb holder counter-
clockwise and remove.
3. Replace the bulb.
4. Insert the bulb holder.
5. Insert the rear side turn signal, arrow 1,
and swing it forward, arrow 2.
6. Proceed in the reverse order to insert
the new bulb and attach the bulb holder.
Make sure that the bulb holder engages
in all fasteners.
Central brake light and license plate
lights
Follow the general instructions on lights
and bulbs, refer to page 281.
The lights feature LED technology. In the
Vehicle battery
case of a malfunction, contact a dealer's
service center or another qualified service
center or repair shop.
General information
The battery is maintenance-free.
287
MOBILITY
Replacing components
More information about the battery can be
- When the inspection glass on the top of
requested from a dealer's service center or
the battery is black.
another qualified service center or repair
- When the take-off performance is insuf-
shop.
ficient.
The following circumstances can have a
Safety information
negative effect on the performance of the
battery:
Warning
- Frequent short-distance drives.
Vehicle batteries that are not compatible
- The vehicle is not used for more than a
can damage vehicle systems and impair
month.
vehicle functions. There is a risk of an ac-
cident and damage to property. Only vehi-
Safety information
cle batteries that are compatible with your
vehicle type should be installed in your ve-
NOTICE
hicle. Information on compatible vehicle
batteries is available at your dealer’s serv-
Battery chargers for the vehicle battery
ice center.
can work with high voltages and currents,
which means that the 12 volt on-board
network can be overloaded or damaged.
Register the battery to the vehicle
There is a risk of damage to property. Only
connect battery chargers for the vehicle
The manufacturer of the vehicle recom-
battery to the starting aid terminals in the
mends that you have a service center or an-
engine compartment.
other qualified service center or repair shop
register the vehicle battery to the vehicle
after the battery has been replaced. Once
Charging the battery
the battery has been registered again, all
comfort features will be available without
Charge the battery only when the engine is
restriction and any Check Control messages
off and via the starting aid terminals, refer
displayed which relate to comfort features
to page 293, in the engine compartment.
will disappear.
Power failure
Charging the battery
After a power loss, some equipment needs
to be newly initialized or individual settings
General information
updated, for example:
Make sure that the battery is always suffi-
- Memory function: store the positions
ciently charged to guarantee that the bat-
again.
tery remains usable for its full service life.
- Time: update.
A discharged battery is indicated by
- Date: update.
a red indicator light.
- Glass sunroof: initialize the system.
Charge the battery in the following situa-
tions:
288
Replacing components
MOBILITY
Disposing of old batteries
boxes, is available on the Internet:
Have old batteries disposed of by a
Where applicable, information on the fuse
dealer’s service center or another
types and locations is also found on a sepa-
qualified service center or repair
rate sheet in the fuse box.
shop or take them to a collection point.
Maintain the filled battery in an upright po-
Replacing fuses
sition for transport and storage. Secure the
battery so that it does not tip over during
The vehicle manufacturer recommends that
transport.
you have a dealer's service center or an-
other qualified service center or repair shop
replace the fuses.
Fuses
Safety information
Warning
Incorrect and repaired fuses can overload
electrical lines and components. There is a
risk of fire. Never attempt to repair a
blown fuse. Do not replace a nonworking
fuse with a substitute of another color or
amperage rating.
Accessing the fuses
The fuses are located in the glove compart-
ment.
1. Open the glove compartment.
2. Swing the cover down, arrow.
Information on the fuse types and locations,
as well as the positions of any other fuse
289
MOBILITY
Breakdown assistance
Breakdown assistance
Vehicle features and options
Warning triangle
This chapter describes all standard, country-
specific and optional features offered with
the series. It also describes features and
functions that are not necessarily available
in your vehicle, e.g., due to the selected op-
tions or country versions. This also applies
to safety-related functions and systems.
When using these functions and systems,
the applicable laws and regulations must be
observed.
The warning triangle is located in the tail-
gate. To remove, loosen the brackets.
Hazard warning flashers
First-aid kit
General information
Some of the articles have a limited service
life.
Check the expiration dates of the contents
regularly and replace any expired items
promptly.
The button is located above the Control Dis-
Storage
play.
The first-aid kit is located in the cargo area.
The red light in the button flashes when the
hazard warning flashers are activated.
MINI Roadside Assistance
Concept
MINI Roadside Assistance can be contacted
if assistance is needed in the event of a
breakdown.
290
Breakdown assistance
MOBILITY
General information
You can launch Teleservice Help by re-
questing it through the Service Specialist.
In the event of a breakdown, data on the ve-
hicle's condition is sent to the vehicle man-
1. Park the vehicle in a safe place.
ufacturer.
2. Set the parking brake.
There are various ways of making contact.
3. Control Display is switched on.
- Via a Check Control message, refer to
4. Confirm Teleservice Help.
page 128.
The driving ability of the vehicle can be re-
- Calling with a mobile phone.
stored for specific functions.
Requirements
If this is not possible, further measures will
be initiated, for instance Roadside Assis-
- Active MINI Connected contract or
tance will be informed.
equipment version with intelligent
emergency call.
- Cellular network reception.
Emergency Request
- The ignition is switched on.
Intelligent emergency call
Starting
If the vehicle is equipped with Teleservices,
Concept
support is offered through Teleservice Diag-
In case of an emergency, an Emergency Re-
nosis.
quest can be triggered automatically by the
Via the Central Information Display (CID):
system or manually.
1.
"MINI Connected"
General information
2. "MINI Assist"
Only press the SOS button in an emergency.
3. "MINI Roadside Assistance"
The Intelligent Assist system establishes a
The contact to the Roadside Assistance
connection with the MINI Response Center.
of the manufacture is established.
For technical reasons, the Emergency Re-
A telephone number is displayed, if
quest cannot be guaranteed under unfavora-
needed. Select to dial the telephone
ble conditions.
number on a connected mobile phone.
Teleservice Diagnosis
Teleservice Diagnosis enables the wireless
transmission of detailed vehicle data that is
important for vehicle diagnosis. This data is
transmitted automatically.
Teleservice Help
Depending on the country, the Teleservice
Help enables a more in-depth diagnosis of
the vehicle via wireless transmission.
291
MOBILITY
Breakdown assistance
Overview
The MINI Response Center then makes
contact with you and takes further steps
to help you.
Even if you are unable to respond, the
MINI Response Center can take further
steps to help you under certain circum-
stances.
For this purpose, data that serves to de-
termine the necessary rescue measures,
for instance the current position of the
vehicle when it can be determined, is
SOS button in the roofliner
transmitted to the MINI Response Cen-
ter.
Functional requirements
If you can no longer hear the MINI Re-
- The ignition is switched on.
sponse Center through the loudspeakers,
the hands-free system, for instance, may
- The Assist system is functional.
be broken. However, the MINI Response
- If the vehicle is equipped with intelli-
Center may still be able to hear you.
gent emergency call: the SIM card
The MINI Response Center ends the Emer-
integrated in the vehicle has been acti-
gency Request.
vated.
Automatic triggering
Jump-starting
Under certain conditions, for instance if the
airbags trigger, an Emergency Request is
automatically initiated immediately after an
General information
accident of corresponding severity. Auto-
If the battery is discharged, the engine can
matic Collision Notification is not affected
be started using the battery of another vehi-
by pressing the SOS button.
cle and two jumper cables. Only use jumper
cables with fully insulated clamp handles.
Manual triggering
1. Press the cover briefly to open it.
Safety information
2. Press the SOS button until the LED at
the button lights up green.
DANGER
- The LED is illuminated green when an
Contact with live components can lead to
Emergency Request has been initiated.
an electric shock. There is a risk of inju-
If the situation allows, wait in your vehi-
ries or danger to life. Do not touch any
cle until the voice connection has been
components that are under voltage.
established.
- The LED flashes green when a connec-
tion to the MINI Response Center has
been established.
292
Breakdown assistance
MOBILITY
Warning
If the jumper cables are connected in the
incorrect order, sparking may occur. There
is a risk of injury. Pay attention to the cor-
rect order during connection.
NOTICE
A special connection on the body acts as the
In the case of body contact between the
battery negative terminal.
two vehicles, a short circuit can occur dur-
ing jump-starting. There is a risk of dam-
age to property. Make sure that no body
Connecting the cables
contact occurs.
To prevent personal injury or damage to
both vehicles, adhere strictly to the follow-
ing procedure.
Preparation
1.
Pull off the lid of the starting aid termi-
1. Check whether the battery of the other
nal.
vehicle has a voltage of 12 volts. The
voltage information can be found on the
2.
Attach one terminal clamp of the posi-
battery.
tive jumper cable to the positive termi-
nal of the battery, or to the correspond-
2. Switch off the engine of the assisting
ing starting aid terminal of the vehicle
vehicle.
providing assistance.
3. Switch off any electronic systems/power
3.
Attach the terminal clamp on the other
consumers in both vehicles.
end of the cable to the positive terminal
of the battery, or to the corresponding
Starting aid terminals
starting aid terminal of the vehicle to be
started.
4.
Attach one terminal clamp of the nega-
tive jumper cable to the negative termi-
nal of the battery, or to the correspond-
ing engine or body ground of assisting
vehicle.
5.
Attach the second terminal clamp to the
negative terminal of the battery, or to
the corresponding engine or body
The starting aid terminal in the engine com-
ground of the vehicle to be started.
partment acts as the battery's positive ter-
minal.
Open the cover of the starting aid terminal.
293
MOBILITY
Breakdown assistance
Starting the engine
Safety information
Never use spray fluids to start the engine.
NOTICE
1. Start the engine of the assisting vehicle
and let it run for several minutes at an
The vehicle can be damaged when towing
increased idle speed.
the vehicle with a lifted rear axle. There is
a risk of damage to property. Have vehicle
2. Start the engine of the vehicle that is to
transported only with lifted front axle or
be started in the usual way.
on a loading platform.
If the first starting attempt is not suc-
cessful, wait a few minutes before mak-
ing another attempt in order to allow the
Pushing the vehicle
discharged battery to recharge.
To remove a broken-down vehicle from the
3. Let both engines run for several mi-
danger area, it can be pushed for a short
nutes.
distance.
4. Disconnect the jumper cables in the re-
For rolling or pushing the vehicle, refer to
verse order.
page 122.
Check the battery and recharge, if needed.
Tow truck
Tow-starting and towing
Safety information
Warning
Due to system limits, individual functions
can malfunction during tow-starting/
towing with the Intelligent Safety systems
Your vehicle should be transported with a
activated. There is a risk of accident.
tow truck with a so-called lift bar or on a
Switch all Intelligent Safety systems off
flat bed.
prior to tow-starting/towing.
NOTICE
Steptronic transmission with
The vehicle can become damaged when
driven front axle: transporting the
lifting and securing it.
vehicle
There is a risk of damage to property.
- Lift the vehicle using suitable means.
General information
- Do not lift or secure the vehicle by its
The vehicle must not be towed if the front
tow fitting, body parts, or suspension
wheels are touching the ground.
parts.
294
Breakdown assistance
MOBILITY
Steptronic transmission with ALL4:
For rolling or pushing the vehicle, refer to
page 119.
transporting the vehicle
General information
NOTICE
The vehicle is not permitted to be towed.
If manual unlocking of the parking brake
is not possible, the vehicle cannot be
Pushing the vehicle
moved or towed. There is a risk of damage
to property. The vehicle should only be
To remove a broken-down vehicle from the
transported on a loading platform.
danger area, it can be pushed for a short
distance.
Follow the following instructions:
For rolling or pushing the vehicle, refer to
page 122.
-
Make sure that the ignition is switched
on; otherwise, the low beams, tail lights,
turn signals, and wipers may be unavail-
Tow truck
able.
-
Do not tow the vehicle with the rear
axle tilted, as the front wheels could
turn.
-
When the engine is stopped, there is no
power assist. Consequently, more force
needs to be applied when braking and
steering.
-
Larger steering wheel movements are
required.
The vehicle should only be transported on a
loading platform.
-
The towing vehicle must not be lighter
than the vehicle being towed; otherwise,
it will not be possible to control the ve-
NOTICE
hicle's response.
The vehicle can become damaged when
-
Do not exceed a towing speed of
lifting and securing it.
30 mph/50 km/h.
There is a risk of damage to property.
-
Do not exceed a towing distance of
- Lift the vehicle using suitable means.
30 miles/50 km.
- Do not lift or secure the vehicle by its
tow fitting, body parts, or suspension
parts.
Manual transmission
Towing or pushing the vehicle
A broken-down vehicle can be towed or
pushed.
295
MOBILITY
Breakdown assistance
Tow truck
NOTICE
With driven front axle
The vehicle can be damaged when towing
the vehicle with a single lifted axle. There
is a risk of damage to property. The vehi-
cle should only be transported on a loading
platform.
NOTICE
The vehicle can become damaged when
lifting and securing it.
Your vehicle should be transported with a
There is a risk of damage to property.
tow truck with a so-called lift bar or on a
- Lift the vehicle using suitable means.
flat bed.
- Do not lift or secure the vehicle by its
tow fitting, body parts, or suspension
NOTICE
parts.
The vehicle can become damaged when
lifting and securing it.
Towing other vehicles
There is a risk of damage to property.
- Lift the vehicle using suitable means.
General information
- Do not lift or secure the vehicle by its
Switch on the hazard warning system, de-
tow fitting, body parts, or suspension
pending on local regulations.
parts.
If the electrical system has failed, clearly
identify the vehicle being towed by placing
a sign or a warning triangle in the rear win-
With ALL4
dow.
Safety information
Warning
If the approved gross vehicle weight of the
towing vehicle is lighter than the vehicle
to be towed, the tow fitting can tear off or
it will not be possible to control the vehi-
cle's response. There is a risk of accident.
Have your vehicle transported on a flatbed
Make sure that the gross vehicle weight of
surface only
the towing vehicle is heavier than the ve-
hicle to be towed.
296
Breakdown assistance
MOBILITY
Tow fitting
NOTICE
If the tow bar or tow rope is attached in-
General information
correctly, damage to other vehicle parts
can occur. There is a risk of damage to
property. Correctly attach the tow bar or
tow rope to the tow fitting.
Tow bar
The tow fittings used should be on the same
side on both vehicles.
Should it prove impossible to avoid mount-
The screw-in tow fitting should always be
ing the tow bar at an offset angle, please fol-
carried in the vehicle.
low the following:
The tow fitting can be screwed in at the
- Maneuvering capability is limited going
front or rear of the vehicle.
around corners.
The tow fitting and the onboard vehicle tool
- The tow bar will generate lateral forces
kit, refer to page 280, are together in the
if it is secured with an offset.
cargo area.
Use of the tow fitting:
Tow rope
- Use only the tow fitting provided with
Observe the following notes when using the
the vehicle and screw it all the way in.
tow rope:
- Use the tow fitting for towing on paved
- Use nylon ropes or straps, which will en-
roads only.
able the vehicle to be towed without
jerking.
- Avoid lateral loading of the tow fitting,
for instance do not lift the vehicle by the
- Make sure the tow rope is not twisted
tow fitting.
when fastening.
- Check the fastening of the tow fitting in
- Check the fastening of the tow fitting
regular intervals.
and tow rope in regular intervals.
- Do not exceed a towing speed of
30 mph/50 km/h.
Safety information
- Do not exceed a towing distance of
3 miles/5 km.
NOTICE
- When starting to tow the vehicle, make
If the tow fitting is not used as intended,
sure that the tow rope is taut.
there may be damage to the vehicle or to
the tow fitting. There is a risk of damage
to property. Follow the notes on using the
tow fitting.
297
MOBILITY
Breakdown assistance
Screw thread for tow fitting
the pedal. After the engine starts, imme-
diately press on the clutch pedal again.
5. Stop at a suitable location, remove the
tow bar or rope, and switch off the haz-
ard warning system.
6. Have the vehicle checked by a dealer's
service center or another qualified serv-
ice center or repair shop.
Threaded holes for the tow fitting are lo-
cated in the front and rear of the vehicle on
the right side with respect to the direction
of travel.
Press on the mark on the edge of the cover
to push it out.
Tow-starting
Steptronic transmission
Do not tow-start the vehicle.
Tow-starting the engine is not possible due
to the Steptronic transmission.
Have the reasons for the starting difficulties
corrected by a dealer’s service center or an-
other qualified service center or repair
shop.
Manual transmission
If possible, do not tow-start the vehicle but
start the engine by jump-starting, refer to
page 292. If the vehicle is equipped with a
catalytic converter, only tow-start while the
engine is cold.
1. Switch on the hazard warning system
and comply with local regulations.
2. Switch on the ignition, refer to
page 102.
3. Engage third gear.
4. Have the vehicle tow-started with the
clutch pedal pressed and slowly release
298
Care
MOBILITY
Care
Vehicle features and options
Distances and temperature
- Maximum temperature: 140 ℉/60 ℃.
This chapter describes all standard, country-
- Minimum distance from sensors, cam-
specific and optional features offered with
eras, seals: 12 inches/30 cm.
the series. It also describes features and
- Minimum distance from glass sunroof:
functions that are not necessarily available
31.5 in/80 cm.
in your vehicle, e.g., due to the selected op-
tions or country versions. This also applies
Automatic vehicle washes
to safety-related functions and systems.
When using these functions and systems,
Safety information
the applicable laws and regulations must be
observed.
NOTICE
Improper use of automatic washing sys-
Washing the vehicle
tems or car washes can cause damage to
the vehicle. There is a risk of damage to
property. Follow the following instruc-
General information
tions:
Regularly remove foreign objects such as
- Give preference to cloth car washes
leaves in the area below the windshield
or those that use soft brushes in or-
when the hood is raised.
der to avoid paint damage.
Wash your vehicle frequently, particularly
- Do not drive through a car wash with
in winter. Intense soiling and road salt can
guide rails higher than 4 in/10 cm to
damage the vehicle.
avoid damage to the chassis.
- Observe the tire width of the guide
Steam jets or high-pressure
rail to avoid damage to tires and rims.
washers
- Fold in exterior mirrors to avoid dam-
age to the exterior mirrors.
Safety information
- With rod antenna: unscrew the rod
antenna to avoid rod antenna break-
NOTICE
age.
When cleaning with high-pressure wash-
- Deactivate the wiper and, if neces-
ers, components can be damaged due to
sary, rain sensor to avoid damage to
the pressure or temperatures being too
the wiper system.
high. There is a risk of damage to property.
Maintain sufficient distance and do not
spray too long continuously. Follow the
Driving into a car wash with a manual
operating instructions for the high-pres-
transmission
sure washer.
In car washes, the vehicle must be able to
roll freely.
299
MOBILITY
Care
Rolling or pushing the vehicle, refer to
Vehicle care
page 119.
Vehicle care products
Driving into a car wash with a
Steptronic transmission
General information
In car washes, the vehicle must be able to
MINI recommends using vehicle care and
roll freely.
cleaning products from MINI. Suitable care
Rolling or pushing the vehicle, refer to
products are available from a dealer’s serv-
page 122.
ice center or another qualified service cen-
Some car washes do not permit persons in
ter or repair shop.
the vehicle. The vehicle cannot be locked
from the outside when in selector lever po-
Safety information
sition N. A signal is sounded when an at-
tempt is made to lock the vehicle.
Warning
Driving out of a car wash
Cleansers can contain substances that are
dangerous and harmful to your health.
Ensure that the vehicle key is in the car.
There is a risk of injury. When cleaning
Start the engine, refer to page 103.
the interior, open the doors or windows.
Only use products intended for cleaning
Headlights
vehicles. Follow the instructions on the
Do not rub wet headlights dry and do not
container.
use abrasive or acidic cleaning agents.
Soak areas that have been dirtied, for in-
Vehicle paint
stance from insects, with shampoo and
wash off with water.
General information
Thaw ice with de-icing spray; do not use an
ice scraper.
Regular care contributes to driving safety
and value retention. Environmental influen-
ces in areas with elevated air pollution or
After washing the vehicle
natural contaminants, such as tree resin or
After washing the vehicle, apply the brakes
pollen can affect the vehicle's paintwork.
briefly to dry them; otherwise, braking ac-
Tailor the frequency and extent of your ve-
tion can be reduced. The heat generated
hicle care to these influences.
during braking dries brake discs and brake
Aggressive substances such as spilled fuel,
pads and protects them against corrosion.
oil, grease or bird droppings, must be re-
Completely remove all residues on the win-
moved immediately to prevent the finish
dows, to minimize loss of visibility due to
from being altered or discolored.
smearing and to reduce wiper noises and
wiper blade wear.
Matte finish
Only use cleaning and care products suita-
ble for vehicles with matte finish.
300
Care
MOBILITY
Leather care
Caring for special components
Remove dust from the leather regularly, us-
ing a cloth or vacuum cleaner.
Light-alloy wheels
Otherwise, particles of dust and road grime
When cleaning the vehicle, use only neutral
chafe in pores and folds, and lead to in-
wheel cleaners having a pH value from 5 to
creased wear and premature degradation of
9. Do not use abrasive cleaning agents or
the leather surface.
steam jets above 140 ℉/60 ℃. Follow the
manufacturer's instructions.
To guard against discoloration, such as from
clothing, clean leather and provide leather
Aggressive, acidic or alkaline cleaning
care roughly every two months.
agents can destroy the protective layer of
adjacent components, such as the brake
Clean light-colored leather more frequently
disc.
because soiling on such surfaces is substan-
tially more visible.
After cleaning, apply the brakes briefly to
dry them. The heat generated during brak-
Use leather care products; otherwise, dirt
ing dries brake discs and brake pads and
and grease will gradually break down the
protects them against corrosion.
protective layer of the leather surface.
Chrome surfaces
Upholstery material care
Carefully clean components such as the ra-
diator grille or door handles with plenty of
General information
water, possibly with shampoo added, partic-
Vacuum the upholstery regularly with a
ularly when they have been exposed to road
vacuum cleaner.
salt.
If upholstery is very dirty, for instance with
beverage stains, use a soft sponge or micro-
Rubber components
fiber cloth with a suitable interior cleaner.
Environmental influences can cause surface
Clean the upholstery down to the seams us-
soiling of rubber parts and a loss of gloss.
ing large sweeping motions. Avoid rubbing
Use only water and suitable cleaning agents
the material vigorously.
for cleaning.
Treat especially worn rubber parts with rub-
Safety information
ber care agents at regular intervals. When
cleaning rubber seals, do not use any sili-
NOTICE
con-containing vehicle care products in or-
der to avoid damage or noises.
Open Velcro® fasteners on articles of
clothing can damage the seat covers.
Fine wood parts
There is a risk of damage to property. En-
sure that any Velcro® fasteners are closed.
Clean fine wood facing and fine wood com-
ponents only with a moist rag. Then dry
with a soft cloth.
301
MOBILITY
Care
Plastic components
to the floor. Do not use loose floor mats
and do not layer several floor mats. Make
sure that there is sufficient clearance for
NOTICE
the pedals. Ensure that the floor mats are
Cleansers that contain alcohol or solvents,
securely fastened again after they were re-
such as lacquer thinners, heavy-duty
moved, for instance for cleaning.
grease removers, fuel, or such, can damage
plastic parts. There is a risk of damage to
Floor mats can be removed from the car's
property. Clean with a microfiber cloth.
interior for cleaning.
Dampen the cloth lightly with water, if
If the floor carpets are very dirty, clean with
needed.
a microfiber cloth and water or a textile
cleaner. To prevent matting of the carpet,
Clean with a microfiber cloth.
rub back and forth in the direction of travel
Dampen the cloth lightly with water, if
only.
needed.
Do not soak the roofliner.
Sensor/camera lenses
To clean sensors and camera lenses, use a
Safety belts
cloth moistened with a small amount of
glass detergent.
Warning
Displays/Screens/Projection lenses
Chemical cleansers can destroy the safety
belt webbing. Missing protective effect of
the safety belts. There is a risk of injuries
NOTICE
or danger to life. Use only a mild soapy sol-
Chemical cleansers, moisture or fluids of
ution for cleaning the safety belts.
any kind can damage the surface of dis-
plays and screens. There is a risk of dam-
Dirty belt straps impede the reeling action
age to property. Clean with a clean, anti-
and thus have a negative impact on safety.
static microfiber cloth.
Use only a mild soapy solution, with the
safety belts clipped into their buckles.
Safety belts should only be allowed to re-
NOTICE
tract if they are dry.
The surface of displays can be damaged
with improper cleaning. There is a risk of
Carpets and floor mats
damage to property. Avoid pressure that is
too high and do not use any scratching
materials.
Warning
Objects in the driver's floor area can limit
Clean with a clean, antistatic microfiber
the pedal distance or block a depressed
cloth.
pedal. There is a risk of accident. Stow ob-
For stubborn soiling on the projection lens
jects in the vehicle such that they are se-
of the Head-up Display, dampen the micro-
cured and cannot enter into the driver's
fiber cloth with alcohol. Projection lens, re-
floor area. Use floor mats that are suitable
fer to page 142.
for the vehicle and can be safely attached
302
Care
MOBILITY
Long-term vehicle storage
When the vehicle is shut down for longer
than three months, special measures must
be taken. Further information is available
from a dealer's service center or another
qualified service center or repair shop.
303
REFERENCE
Technical data
Technical data
in your vehicle, e.g., due to the selected op-
Vehicle features and options
tions or country versions. This also applies
to safety-related functions and systems.
This chapter describes all standard, country-
When using these functions and systems,
specific and optional features offered with
the applicable laws and regulations must be
the series. It also describes features and
observed.
functions that are not necessarily available
General information
The technical data and specifications in the
values can be found in the approval docu-
ments, on labels on the vehicle or can be ob-
ues. The vehicle-specific data can deviate
tained from a dealer’s service center or an-
from this, for instance due to the selected
other qualified service center or repair
special equipment, country version or coun-
shop.
try-specific measurement method. Detailed
Dimensions
The dimensions can vary depending on the
tenna, roof racks or spoiler. The heights can
model version, equipment or country-spe-
deviate, for instance due to the selected
cific measurement method.
special equipment, tires, load and chassis
version.
The specified heights do not take into ac-
count attached parts, for instance a roof an-
MINI Countryman
Width with mirrors
in/mm
78.9/2,005
Width without mirrors
in/mm
71.7/1,822
Height
in/mm
61.3/1,557
Length
in/mm
169.8/4,314
Wheelbase
in/mm
105.1/2,670
Smallest turning radius diam.
ft/m
37.4/11.4
304
Technical data
REFERENCE
Weights
MINI Cooper Countryman
Approved gross vehicle weight
lbs/kg
4,376/1,985
Load
lbs/kg
851/386
Approved front axle load
lbs/kg
2,326/1,055
Approved rear axle load
lbs/kg
2,183/990
MINI Cooper S Countryman
Approved gross vehicle weight
lbs/kg
4,542/2,060
Load
lbs/kg
968/439
Approved front axle load
lbs/kg
2,403/1,090
Approved rear axle load
lbs/kg
2,260/1,025
MINI Cooper Countryman ALL4
Approved gross vehicle weight
lbs/kg
4,564/2,070
Load
lbs/kg
Approved front axle load
lbs/kg
2,403/1,090
Approved rear axle load
lbs/kg
2,293/1,040
MINI Cooper S Countryman ALL4
Approved gross vehicle weight
lbs/kg
4,696/2,130
Load
lbs/kg
902/409
Approved front axle load
lbs/kg
2,469/1,120
Approved rear axle load
lbs/kg
2,337/1,060
MINI John Cooper Works Countryman ALL4
Approved gross vehicle weight
lbs/kg
4,696/2,130
Load
lbs/kg
871/395
305
REFERENCE
Technical data
MINI John Cooper Works Countryman ALL4
Approved front axle load
lbs/kg
2,502/1,135
Approved rear axle load
lbs/kg
2,337/1,060
Capacities
MINI Countryman
Fuel tank, approx.
US gal/liters
16.1/61.0
Observe further information on fuel quality,
refer to page 246.
306
Appendix
REFERENCE
Appendix
vehicle are listed here.
Updates made after the edito-
rial deadline
The following chapters were updated in the
the editorial deadline for the Integrated
- Notes: notes: own safety: maintenance.
- Quick Reference Guide: on the road: re-
fueling stop: topping up the engine oil.
- Driving tips: observe when driving: driv-
ing on a race track.
- Mobility: engine oil: topping up the en-
gine oil.
- Mobility: coolant: coolant level.
- Mobility: preventive maintenance: MINI
maintenance system.
- Mobility: preventive maintenance: Con-
dition Based Service CBS.
- Mobility: preventive maintenance: Main-
tenance Manual and Service and War-
ranty Information Booklet for US models
and Warranty and Service Guide Booklet
for Canadian models.
307
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст