Skoda Karoq (2021 year). Manual in english — page 3

Lighting, windscreen wipers and washers › Exterior lighting

Warning lights

Lighting, windscreen wipers and

▶ After switching on the igni-

washers

tion, the two indicator lights

light up brieĔû.

Exterior lighting

▶ If the system is OK, both of

Functionality

the indicator lights go out.

▶ One of the indicator lights then lights up again de-

Unless otherwise stated, the light works when the

pending on the position of the key switch:

ignition is switched on.

lights up - front passenger airbag switched

Daylight running lights

off

The daytime running lights illuminate the area in

lights up 65 secs after the ignition is

front of the vehicle.

switched on - passenger front airbag

In vehicles for certain markets, this also provides

switched on

lighting for the rear area of the vehicle.

Operating conditions

✓ The lights switch is in position

Troubleshooting

Switching the low beam oÄ/off automatically

Key switch for airbag deactivation is faulty

The low beam is automatically switched on or off de-

Ĕashes together with

pending on the lighting conditions.

The front passenger airbag will not be de-

ployed in the event of an accident!

Operating conditions

✓ The light switch is in the

position.

› Have the airbag system checked by a specialist ga-

rage immediately.

The automatic headlight circuit is indicated by the il-

lumination of the symbol

in the light switch.

Switching low beam on automatically in rain

Operating conditions

✓ The light switch is in the

position.

✓ The function is activated.

✓ The windscreen wipers are switched on for lon-

ger than 30 seconds.

The automatic headlight circuit is indicated by the il-

lumination of the symbol

in the light switch.

Full LED Headlights

When the light switch is in position

, the head-

lights provide the best possible beam of light in front

of the vehicle. The Dynamic cornering light function

ensures the best possible illumination of the curve

area.

CORNER function

The CORNER function is intended for turning or ma-

noeuvring (e.g. when parking).

The function illuminates the vicinity of the vehicle

front in the direction of travel.

Operating conditions

✓ The turn signal is switched on or the front wheels

are steered sharply.

✓ The low beam is switched on.

✓ The fog lights are not switched on.

✓ The driving speed is lower than 40 km/h.

When no light is switched on

The symbol in the light switch may also light up in

the instrument cluster, indicating that it is necessary

to switch on the light.

Lighting, windscreen wipers and washers › Exterior lighting

illuminates

Tap the lever in the opposite direction ahead of

time to stop signalling.

› Switch on the light.

Fog light

Positions for pulling out

Operation

the light switch

Switching off the

Fog lights - when

lights except the

switched on, the in-

daytime running

dicator light in the

lights

instrument cluster il-

Switching the low

luminates

beam oÄ/off auto-

Rear fog light - when

matically

switched on, the in-

Switching on the

dicator light in the

parking lights

instrument cluster illuminates

Switching on the low

› Turn the light switch to position

beam

›

Pull the light switch to the appropriate position.

As the basic position of the light switch, use posi-

The rear fog light does not illuminate when an ac-

tion

cessory is connected to the trailer socket.

High beam and headlight Ĕasher

Hazard warning light system

The high beam works when the low beam is on.

› Press the button to switch on or off in the mid-

Switch on high beam

dle part of the control panel.

Switch off main

The hazard warning lights can be switched on auto-

beam / switch on

matically during hard braking. The hazard warning

headlight Ĕasher

lights are then switched off again automatically

when starting off or accelerating.

When the main beam or

When the hazard warning system is on and the

headlight Ĕasher is

turn signal is switched on, the hazard warning lights

switched on, the indica-

will be switched off temporarily and only the turn

tor lamp lights up in the instrument cluster

signal will Ĕash on the relevant side of the vehicle.

CAUTION

Risk of an accident!

One-sided parking light

▶ Do not dazzle other road users with the high beam.

The one-sided parking light allows one side of the

parked vehicle to be illuminated through activation

Turn signal

of the corresponding sidelights.

Switching on the

Switch on the side-

turn signal light on

lights on the right

the right - the warn-

Switch on the side-

ing light Ĕashes in

lights on the left

the instrument clus-

ter

› Switch off the ignition.

Switching on the

› Move the lever to the

turn signal light on

appropriate position.

the left - the warn-

› Lock the vehicle.

ing light Ĕashes in

When the parking light is

the instrument clus-

switched on, an acoustic

ter

warning signal sounds and the driver's door is

Turn signal - convenience signalling

opened. After a few seconds or after the driver's

Convenience signalling enables three Ĕashes of the

door is closed, the warning signal will stop.

turn signal lights without having to move the lever

Double-sided parking light

up or down.

The two-sided parking light allows the parked vehi-

› Tap the control lever up or down.

cle to be illuminated through activation of the side-

lights.

The corresponding turn signal lights Ĕash three

times.

› Turn on the ignition.

Lighting, windscreen wipers and washers › Exterior lighting

› Turn the light switch to position

Adjust headlights for driving in right / left-hand

traffic

› Switch off the ignition.

Applies to full LED headlights.

› Lock the vehicle.

When the parking light is switched on, an acoustic

› In Infotainment, select the following menu:

warning signal sounds after the ignition is switched

off and the driver's door is opened. After a few sec-

Or:

onds or after the driver's door is closed, the warning

signal will stop.

› Activate the travel mode function.

The light may switch off automatically if the 12-volt

vehicle battery is too low. If the parking lights on

both sides are switched on with the ignition off, the

Troubleshooting

lights will not be switched off automatically and the

12 volt vehicle battery may be discharged.

Turn signal light defective

Ĕashes faster - turn signal light on the right de-

fective

Settings

›

Check the turn signal light on the right.

Activating/deactivating the automatic headlights

Ĕashes faster - turn signal light on the left de-

system in rain

fective

The function is activated or deactivated in the fol-

lowing menu in the Infotainment system:

› Check the turn signal light on the left.

does not Ĕash when the trailer is hitched -

Or:

trailer turn signal light defective

› Check the trailer lighting.

Activating/deactivating convenience signalling

Light bulb or LED bulb is defective

The function is activated or deactivated in the fol-

illuminates

lowing menu in the Infotainment system:

Information appears in the display regarding

the defective lights.

Or:

› Replace the defective bulb.

› In case of a defective LED bulb, contact a specialist

garage for help.

Headlight range control of the Halogen headlights

› In Infotainment, select the following menu:

The headlights are misted up on the inside

Inside the headlights, moisture may occur. This is not

a defect.

Or:

Malfunction of the automatic headlight circuit

› Clean the windscreen in the area of the rain/light

› Adjust the headlight range using the slider. The

sensor.

headlight range must correspond to the vehicle's

load.

Beam of light in front of the vehicle has shortened

Headlight defective.

Front seats occupied, boot empty

All seats occupied, boot empty

› Seek the help of a specialist garage.

All seats occupied, boot loaded

Driving lights defective

Driver's seat occupied, boot loaded

If a message regarding the failed driving lights is dis-

In the event of another vehicle loading condition, the

played, the light will work in emergency mode.

positions ,

can be used.

› Drive on, exercising appropriate caution.

For the Full LED headlights, the headlight range

› Seek the help of a specialist garage.

control is adjusted automatically.

WARNING

Risk of an accident!

An incorrectly adjusted headlight range can cause in-

suffiieÄt vehicle lighting or can dazzle other road

users.

▶ Adjust the headlight range correctly.

Lighting, windscreen wipers and washers › COMING HOME, LEAVING HOME exterior lighting

COMING HOME, LEAVING HOME

Operation

exterior lighting

Switching on

Functionality

› Push the lever in the

direction of the arrow.

The COMING HOME function turns on the light after

It lights up in the instru-

turning off the ignition and opening the driver's door.

ment cluster

from

The light switches off automatically after the set

the isolation box.

lighting time has elapsed.

The LEAVING HOME function switches on the light

when unlocking the vehicle with the wireless remote

Switching off

control.

› Manually switch the high beam on or off.

Operating conditions

Function restriction

✓ Visibility has worsened.

The system may dazzle other road users if their

✓ The light switch is in the

position.

headlights/lights are not detected for the following

reasons, for example:

▶ The headlights/lights of oncoming vehicles are

Settings

covered by crash barriers, for example.

This function is set in the following menu in the Info-

▶ The headlamps/lights of the oncoming or preced-

tainment system:

ing vehicle are dirty or not functioning.

Or:

Settings

Activation/deactivation

The function is activated or deactivated in the fol-

lowing menu in the Infotainment system:

Light Assist high-beam assist system

Functionality

Or:

The high beam assist system automatically switches

the high beam on and off.

WARNING

Replace light bulbs

Risk of accident!

▶ If necessary, manually switch the high beam on or

What you should be mindful of

off.

DIY replacement of the following bulbs is possible.

Have the remaining light sources replaced by a spe-

Operating conditions

cialist garage.

✓ The system is activated.

The new bulb must conform to the speifiatioÄ of

the original light bulb. The name of the bulb is

✓ The light switch is in the

position.

marked on the bulb socket.

✓ The driving speed is higher than 30 km/h or 60

km/h (depending on the vehicle equipment).

After changing a bulb in the low beam light, the main

✓ The low beam is switched on.

beam or fog light, have the headlights adjusted by a

specialist garage.

CAUTION

Halogen lamps are pressurised and can burst during

replacement!

▶ Wear gloves and safety goggles.

Lighting, windscreen wipers and washers › Replace light bulbs

NOTICE

Front parking light

Contamination of the halogen lamp reduces the life

of the lamp!

› Remove the protective

cap from the headlight.

▶ Do not touch the glass of the light bulb with your

bare fiÄ£ers.

NOTICE

Danger of headlight damage due to the ingress of

water and dirt!

▶ Always fit the protective cap on the headlight cor-

rectly after changing a bulb.

Conditions for changing a bulb

› Press the locking lugs

and remove the base

✓ Ignition off

with the bulb.

✓ Light switched off

Low beam and high beam

Protective caps on the

headlight:

Low beam

› Change the bulb in the

Main beam

socket.

› Insert the socket with

› Remove the associated

the bulb into the head-

protective cap.

light until the locking

lugs engage.

› Fit the protective cap

on the headlight again.

› Press the locking lug

and remove the base

with the bulb.

› Change the bulb in the

socket.

Front turn signal

› Remove the protective

cap from the headlight.

› Insert the socket with

the new light bulb into

the headlight, so that

the fixiÄ£ lug A is

pointing up.

› Insert the socket until

› Remove the base with

it clicks into place.

the bulb.

› Fit the protective cap

on the headlight again.

Lighting, windscreen wipers and washers › Replace light bulbs

› Change the bulb in the

› Turn the bulb and re-

socket.

move it.

› Insert the socket with

› Release the connector

the light bulb into the

and remove it from the

light so that the fixiÄ£

bulb.

lugs A fit into the re-

cesses on the head-

light.

› Fit the protective cap

on the headlight again.

Inserting a new bulb and cover cap in the wheel

arch

Fog lights

›

Insert the plug into the new bulb until it clicks into

Removing the cover cap from the wheel housing

place.

› Adjust the front wheels so that the cover cap is ac-

› Insert the new bulb into the headlight so that the

cessible.

guide lugs on the bulb are aligned with the corre-

sponding openings in the headlight.

› Insert the bracket from

the tool kit into the re-

› Turn the bulb clockwise to secure.

cess in the cover cap.

› Replace the rubber protective cap on the headlight.

› Remove the cover by

› Insert the cover in the wheel arch and lock into

pulling on the bracket.

place.

Rear turn signal and reversing lights

Loosen and remove the light

›

Open the relevant cover in the luggage compart-

Removing the defective light bulb

ment.

› Remove the rubber

protective cap from

the headlight.

Cover on the left

Cover on the right - vehicle with standard rear

seats

Cover on the right - vehicle with VarioFlex rear

seats

Lighting, windscreen wipers and washers › Interior lighting

› Unscrew the screw.

▶ Make sure that no cables are trapped when insert-

ing the holder into the lamp.

Insert and fix the light

›

Insert the connector into the light until it clicks into

place.

› Push in the slightly pulled out locking device on the

plug.

› Remove the light.

› Insert the lamp with the strips A into the grooves

B in the bodywork and push in carefully until it

› Slightly pull out the

stops.

lock A at the plug.

NOTICE

› Press the safety button

Risk of damage to the electrical system due to water

and remove the plug.

ingress!

▶ Make sure that the seal is used correctly when in-

stalling the lamp C .

NOTICE

Risk of damage to the electrical system!

▶ Make sure that the lines between the lamp and the

body are not pinched when the lamp is inserted.

Replacing the light bulb

› Screw the light into place.

› Unlock and remove the

› Close and lock the cap.

lamp holder A .

Interior lighting

Operation

Operation of the lighting

Switching on

Rear lighting

Switching off

› Change the bulb in the

Reading lamp left

socket.

Reading lamp right

› The base for the bulb

Automatically switch on and switch off

in the turn signal light

The switch without the symbol is the mid-

is marked with

dle position of the switch

The base for the bulb

Switching on automatically

in the reverse light is

The lighting switches on when one of the following

marked with

events occurs.

› Check that the plug A

▶ The vehicle is unlocked

securely connected.

▶ One of the doors is opened

› Insert the bulb holder into the light and snap into

▶ The ignition key is removed (vehicle without start-

place.

er button)

NOTICE

Risk of damage to the electrical system!

Lighting, windscreen wipers and washers › Interior ambient light

Automatic switch off

Windscreen wipers and washers

The lighting switches off when one of the following

events occurs:

Operating conditions

▶ The vehicle is locked

✓ Engine compartment Ĕap closed

▶ The ignition is switched on

✓ Boot lid closed

▶ About 30 seconds after all the doors have been

✓ Ignition on

closed

If a door remains open and the ignition is switch-

Operation

ed off, the lights will turn off automatically after 10

minutes.

WARNING

Automatic switching oÄ/off of the footwell light-

Risk of an accident!

ing

At low temperatures, windscreen washer Ĕuid can

The lighting only works when the dipped or parking

freeze on the windscreen and restrict visibility.

lights are on.

▶ Only use the windscreen washer when the wind-

screen is warm.

The lighting is also switched on automatically after

opening the door (e.g. when getting in or out).

Wipe and wash the windscreen

Turn on the lighting for the make-up mirror in the

sun visors on the windscreen

› Slide off the cover of the make-up mirror.

Settings

The brightness level of the footwell lighting is set in

the Infotainment in the following menu when the

low beam or parking light is switched on:

Fast wiping

Or:

Slow wiping

Depending upon vehicle equipment:

▶ Intermittent wiping

▶ Automatic wiping controlled by the rain sensor

Interior ambient light

Switching off

Usage

Tip-wiping (spring-loaded position)

The ambient lighting ensures a comfortable atmos-

Setting the wiping speed for the position

phere in the vehicle interior.

Washing and wiping (spring-loaded position)

The lighting only works when the dipped or parking

lights are on.

Depending on the vehicle equipment, the wind-

The lighting is also switched on automatically after

screen washer nozzles of the windscreen can be

opening the door.

heated automatically.

Clean headlights

When the headlights are switched on, they are

Settings

cleaned the first time and after every tenth wash of

The background lighting brightness settings are set

the windscreen. Setting the spray interval can be

in the Infotainment system, in the following menu:

carried out by a specialist garage.

Or:

Lighting, windscreen wipers and washers › Windscreen wipers and washers

Wipe and wash the rear window

▶ Close the container after refilliÄ£ the windscreen

washer Ĕuid.

The windscreen washer tank is located in the engine

compartment » page 12.

The container can hold a volume of 5 litres or 3 litres

and 5 litres for vehicles with a headlight cleaning

system depending on the engine type.

› Open the engine compartment lid » page 198.

› Gently open the top of the sealing cap.

› Top up the windscreen washer Ĕuid.

Spring-loaded position:

› Close the sealing cap of the tank.

▶ Washing and wiping the windscreen

▶ Cleaning the rear view camera

Troubleshooting

Wiping

Windscreen washer Ĕuid level too low

Switching off

illuminates together with

Automatic rear window wiping

If the windscreen wiping is performed without inter-

ruption, then the automatic regular intermittent wip-

illuminates together with

ing of the rear window takes place.

When the windscreen wipers are switched on, the

› Top up the windscreen washer Ĕuid.

rear window is automatically wiped when the re-

Frozen windscreen wipers

verse gear is engaged.

Carefully remove frozen windscreen wipers from

›

the windscreen before switching on the ignition

Settings

and free them from snow and ice.

Activating/deactivating automatic wiping

The functions for automatic rear window wiping and

Folding down windscreen wiper arms and

automatic wiping in the rain can be activated and de-

replacing windscreen wiper blades

activated in the following menu in the Infotainment

system:

For folding down the windscreen wiper from the

screen you must first adjust the wiper arms to the

folded position.

Or:

NOTICE

Risk of damage to the windscreen wipers and the

engine compartment lid!

▶ Close the bonnet before lowering the wiper arms

RefilliÄg windscreen washer Ĕuid

from the window.

WARNING

▶ Do not turn on the ignition when the windscreen

Risk of an accident!

wiper arms are folded away.

▶ Use windscreen washer Ĕuid that is suitable for the

Set the windscreen wiper arms into the folding po-

weather conditions.

sition

NOTICE

› Switch the ignition on and off again.

Risk of damage to the windscreen washer system!

› Within 10 seconds,

▶ When refilliÄ£ the washer Ĕuid, do not remove the

press the control lever

strainer from the neck of the container.

down and hold for

NOTICE

about 2 seconds.

Risk of damage to the headlights!

▶ Only use washer Ĕuid that does not attack polycar-

bonates.

NOTICE

Risk of damage to engine compartment compo-

nents!

Heating and air conditioning system › Manual air conditioning

Replace the windscreen wiper blade

Heating and air conditioning

CAUTION

system

Risk of accident!

▶ Change the windscreen wiper blades once or twice

Manual air conditioning

a year.

What you should be mindful of

› Fold the windscreen wiper arm away from the

windscreen.

▶ We recommend keeping the interior temperature

› Press the catch and re-

no more than 5 ° C lower than the outdoor tem-

move the wiper blade.

perature.

› Insert the new wiper

▶ We recommend switching the cooling system off

blade until it clicks into

about 10 minutes before the end of the journey to

place.

prevent odour formation.

› Fold the windscreen

▶ Annual disinfection of the air conditioning is rec-

wiper arm back onto

ommended.

the windscreen.

WARNING

› Turn on the ignition

Danger of misting!

and push the control

▶ Always keep the fan on.

lever down.

WARNING

Risk of accident!

In recirculation mode, there is no fresh air supply

from the outside. This can result in loss of driver at-

tention and fogging up of windows.

▶ Keep the recirculation mode switched on for a

short time only.

Operating conditions for the cooling system

✓ Outside temperature above 2 ° C

✓ Running engine

✓ Fan switched on

Overview of the controls for the manual air

conditioning

Set the temperature

Set the blower speed

Set the direction of the air outlet

Switch the seat heating oÄ/off » page 63, Oper-

ation

Switch the cooling system oÄ/off

Switch oÄ/off the windscreen heat-

ing » page 63, Operation

Switch recirculated air mode oÄ/off

Heating and air conditioning system › Climatronic automatic air conditioning system

Switch auxiliary heating and ventilation

Climatronic automatic air conditioning

oÄ/off » page 61, Usage

system

Cooling system

What you should be mindful of

When the cooling system is switched on, the tem-

perature and humidity in the vehicle will drop.

▶ We recommend keeping the interior temperature

no more than 5 ° C lower than the outdoor tem-

Switching on the cooling system prevents the win-

perature.

dows from misting up.

▶

We recommend switching the cooling system off

After pressing the

button, the indicator light

about 10 minutes before the end of the journey to

in the button illuminates, even if the conditions for

prevent odour formation.

switching on the cooling system are not met. The

▶ Annual disinfection of the air conditioning is rec-

cooling system switches on when the conditions for

ommended.

switching on the cooling system are met.

WARNING

Automatic activation of the cooling system

Danger of misting!

Automatic activation of the cooling system prevents

▶ Always keep the fan on.

the windows from misting up. The system switches

on in the following cases.

WARNING

Risk of accident!

▶ When the fan is on and the air distribution control-

In recirculation mode, there is no fresh air supply

ler is in the

position.

from the outside. This can result in loss of driver at-

In this case, the recirculation mode is switched off.

tention and fogging up of windows.

▶ When the air distribution controller is not in the

▶ Keep the recirculation mode switched on for a

position, and recirculated air mode is switched on.

short time only.

Recirculated air mode

The recirculation mode prevents contaminated out-

Operating conditions for the cooling system

side air getting into the interior of the vehicle.

✓ Outside temperature above 2 ° C

BrieĔû switching on recirculation mode can increase

the cooling effet.

✓ Running engine

✓ Fan switched on

Under certain circumstances, the recirculation

mode may be switched on or off automatically.

When the air conditioner is operating, the engine

Operation

idle speed may increase automatically.

Troubleshooting

Water under the vehicle

When the cooling system is switched on, water can

drip off the air conditioning system. This is not a leak.

Fogging

Set the temperature for the left side

› Increase the blower speed, switch on the cooling

system, and set the air distribution to the wind-

Set the temperature for the right side

screen.

Set the direction of the air outlet

Automatic sõitch-off of the cooling system

Set the blower speed

If the coolant temperature is too high, the cooling

Set the temperature for the left side

system may switch off automatically. This ensures

suffiieÄt engine cooling.

Set the temperature for the right side

Depending on the equipment:

▶ Switch auxiliary heating and ventilation

oÄ/off » page 61, Usage

▶

Switching Climatronic system off

Interior temperature sensor

Heating and air conditioning system › Climatronic automatic air conditioning system

Switch the seat heating oÄ/off » page 63, Op-

eration

Switch recirculated air mode oÄ/off

The recirculation mode prevents contaminated

outside air getting into the interior of the vehi-

cle.

Switch the windscreen ventilation/defrosting

mode oÄ/off

Switch oÄ/off the windscreen heat-

ing » page 63, Operation

Select Climatronic mode

Switch oÄ/off the windscreen heat-

Set the direction of the air outlet in manual

ing » page 63, Operation

mode

Operate Climatronic in the Infotainment sys-

Set the temperature for the left side

tem

Set the temperature for the right side

Switch maintenance of the interior tempera-

ture oÄ/off according to the temperature set-

Show the front settings menu

ting for the driver's side

Show the back settings menu

Press - Switch on automatic mode

Switch the cooling system oÄ/off

This function keeps the temperature constant

When the cooling system is switched on, the

and prevents the windows from misting.

temperature and humidity in the vehicle will

Hold - Maintain the interior temperature in ac-

drop.

cordance with the temperature setting for the

Switching on the cooling system prevents the

driver side (SYNC function)

windows from misting up.

Switch the cooling system oÄ/off

Switching the windscreen heater

When the cooling system is switched on, the

oÄ/off » page 63, Operation

temperature and humidity in the vehicle will

According to the selected Climatronic mode:

drop.

▶ Manual mode - Set the blower speed

Switching on the cooling system prevents the

▶ Automatic mode - Set the operating power

windows from misting up.

Switch maintenance of the interior temperature

The rear temperature can also be set on the dis-

oÄ/off according to the temperature setting for

play in the centre console at the rear.

the driver's side

With a temperature setting outside of the number

The Air Care function reduces the penetration

range, one of the following icons will be displayed in

of pollutants into the vehicle interior. At the

the Climatronic display:

same time, the air is both circulated and

cleaned.

LO Maximum cooling power

The air purifiatioÄ process is displayed in the

Maximum heating power

Infotainment.

When the air conditioner is operating, the engine

For proper operation, the doors and windows

idle speed may increase automatically.

must be closed.

› To switch oÄ/off Active .

Settings

Switch auxiliary heating and ventilation

oÄ/off » page 61, Usage

Display the settings menu

Lock increases in heat output for the rear seat

› Tap the

button on the Climatronic.

heater » page 63, Operation

Or:

The function is displayed after tapping the func-

› Tap on

in the Infotainment screen.

tion surface F .

Further Climatronic settings

› To make further settings, press the

button on

the Climatronic

, tap on in the Infotainment

screen.

Heating and air conditioning system › Auxiliary heating and ventilation

▶ Automatic air recirculation

- Automatic air circulation mode

conditioning system and the air outlet nozzles before

oÄ/off

the ignition is switched off.

▶ Automatic supplementary heater - Switch fast interior heating

The system consumes fuel from the fuel tank when

oÄ/off

operating the heating.

▶ Automatic windscreen heating - Switch oÄ/off the automatic

windscreen heating

Operating conditions

Troubleshooting

✓ The charge state of the 12-volt vehicle battery is

suffiieÄt.

Water under the vehicle

✓ The fuel supply is suffiieÄt, the instrument clus-

When the cooling system is switched on, water can

ter does not light up

drip off the air conditioning system. This is not a leak.

Fogging

Operation

› Switch on automatic mode.

Or:

Switch oÄ/off with the radio remote control

› Hold down the corresponding key.

› Increase the blower speed, switch on the cooling

system, and set the air distribution to the wind-

Indicator light

screen.

Antenna

Automatic sõitch-off of the cooling system

Switching off

If the coolant temperature is too high, the cooling

Switching on

system may switch off automatically. This ensures

suffiieÄt engine cooling.

Auxiliary heating and ventilation

Usage

Hold the radio remote control with the antenna

facing upwards.

The auxiliary heater heats the vehicle interior and the

engine.

NOTICE

▶ Protect the remote control from moisture, strong

The auxiliary ventilation makes it possible to supply

vibrations and direct sunlight.

fresh air to the vehicle interior when the engine is

switched off. As a result, the interior temperature is

Display of the radio remote control indicator light

lowered, e.g. when the vehicle is parked in the sun.

▶ Lit up green for 2 seconds - switch on

▶ Lit up red for 2 seconds - switch off

What you should be mindful of

Range of the radio remote control

The range of the wireless remote control is a few

DANGER

hundred meters when the battery is full. For exam-

Risk of poisoning!

ple, obstacles or weather conditions can reduce the

▶ The auxiliary heater must not be operated in en-

range.

closed spaces.

Switching oÄ/off via the control panel of the air

DANGER

conditioning system

Risk of fire!

› Press the button.

▶ Switch off the auxiliary heater before refuelling.

▶ The exhaust pipe for the auxiliary heater is located

on the underside of the vehicle. Therefore, do not

Set automatic switching on

stop the vehicle in places where the exhaust gases

Show the menu for vehicles with manual air condi-

could come into contact with easily Ĕammable ma-

tioning

terials, e.g. dry grass, spilled fuel etc.

The automatic switching on is set in the following

menu in the Infotainment system.

Functionality

The system heats or ventilates the vehicle interior

Or:

depending on the temperature settings of the air

Heating and air conditioning system › Auxiliary heating and ventilation

Show menu for vehicles with Climatronic

Troubleshooting

› Press the button

on the Climatronic control

Smoke in the engine compartment

panel

, tap

in the Infotainment screen.

In the engine compartment, smoke and odours may

Settings and information in the Infotainment

form during the operation of the auxiliary heater.

screen

This is not a defect.

Running the auxiliary heater after stopping the en-

gine

After switching off the system, the coolant pump

and the auxiliary heating will continue running a little

while longer in order to burn the remaining fuel in

the heating.

Indicator light in the radio remote control

▶ Flashes green in a slow sequence - the switch-on

signal was not received

Day and time when the vehicle is to be ready for

▶ Flashes red in a slow sequence - the sõith-off sig-

use

nal was not received

Setting the heating/ventilation

▶ Flashes green in an irregular pattern - the parking

heater is locked, e.g. because the fuel tank is al-

List of pre-selected times, activation / deactiva-

most empty or there is an error

tion of the preset time

› Check the level of fuel.

Set the selected choice of time and the duration

(10-60 minutes)

› If the fuel quantity is OK, seek the help of a spe-

cialist company.

Immediate switch-on

▶ Lights up orange first, then green/red - the battery

When the heating is running, the windows are

is weak, the oÄ/off signal has been received

displayed in red

▶ Lights up orange first, then Ĕashes green/red - the

When ventilation is running, the windows are

battery is weak, the oÄ/off signal has not been re-

displayed in blue

ceived.

▶ Flashing orange - the battery is nearly discharged,

the oÄ/off signal has not been received

▶ Not lit up - the battery is discharged, the oÄ/off

signal has not been received

› Replace the battery.

Change the battery in the remote control

WARNING

Currently displayed preset time

Risk of death!

If the battery is swallowed, serious or even fatal inju-

Activation of the currently displayed preset time

ries can result from burns in the digestive tract.

Setting the departure time

▶ Always keep children away from the radio remote

control and batteries.

When automatic switching on is activated, the warn-

▶ If the battery is swallowed, seek medical help im-

ing light in the button lights up after the ignition is

mediately.

turned off.

› Use a thin screwdriver

Only one preset time can be active. The activated

to remove the cover in

preset time will be deactivated again after it has

the marked area.

started automatically. To start the next preset time,

this preset time must be activated.

› Open the cover and

push it out.

When selecting the day in the preset time, there

is an option between Sunday and Monday without

the speified day. When this position is selected, the

system is switched on at the next set time.

Heating and air conditioning system › Heated windscreen

› Use a screwdriver to

Troubleshooting

loosen the battery in

The indicator light in the button or below the but-

the marked area.

ton Ĕashes

› Replace the battery.

The heating does not work as the battery charging

› Insert the cover and

level of the 12 volt vehicle battery is too low.

push it until it audibly

locks into place.

Seat heating

What you should be mindful of

WARNING

Heated windscreen

Risk of burns!

▶ Do not switch on the seat heater for persons with

Usage

limited perception of pain or temperature.

Windscreen heating is used for defrosting or venti-

NOTICE

lating the windscreen.

Risk of seat damage!

▶ Do not kneel on the seats or otherwise apply con-

centrated pressure to them.

Requirements

▶ Do not turn on the heater in the following situa-

✓ Running engine

tions:

▶ The seat is not occupied.

✓ Outside temperature approximately below 35 ° C

▶ There are objects on the seat, such as a child

seat.

Operation

▶ There are additional seat covers or protective

covers on the seat.

Heated rear window

› Press the button.

Heated windscreen

Requirements

› Tap the button on the Climatronic.

✓ Running engine

Or:

› Press the key

on the Climatronic

, tap in

Operation

the Infotainment screen.

Windscreen heating switches off automatically after

› Press the or button on the Climatronic to

switch on the front seat heating.

some time.

› Press the or button in the rear centre console

If the engine is switched off when the heating is on

to switch on the rear seat heating.

and turned back on again within about 10 minutes,

the heating is continued.

The heating is switched on with maximum heating

output. By repeatedly pressing the button, the heat-

ing output is reduced until it is switched off.

Settings

The output level of the heating is indicated by the

number of illuminated indicator lights in the button

Automatic heated windscreen

or in the Infotainment screen.

The heated windscreen switches on automatically if

the windscreen mists up.

› Press the button

on the Climatronic control

Settings

panel

, tap

in the Infotainment screen.

Lock increases in heat output for the rear seat

Or:

heater

› Tap on

in the Infotainment screen.

› To turn the function on or off, press the

but-

ton on the Climatronic

in the Infotain-

ment screen.

Or:

› Tap on

in the Infotainment

screen.

Heating and air conditioning system › Heated steering wheel

When the function is switched on, the heating out-

Driver information system

put can only be turned down.

Analogue instrument cluster

The function also blocks the possibility of setting

the temperature in the display in the rear centre con-

Overview

sole.

Overview of instrument cluster

Heated steering wheel

Requirements

✓ Running engine

Operation

› Press the button on the multifunction steering

wheel.

Tachometer with indicator lights

The heating is switched on with maximum heating

output. By repeatedly pressing the button, the heat-

Display

ing output is reduced until it is switched off.

Speedometer with indicator lights

Bar with indicator lights

Multifunction button:

▶ Setting the time

▶ Reset odometer (trip)

▶ Show distance and days until next service ap-

pointment

Coolant temperature gauge

Fuel gauge

NOTICE

Risk of serious damage to the engine and the ex-

haust system!

▶ Never run the fuel tank completely empty!

In poor visibility and with dipped headlights off,

the brightness of the instrument cluster lighting is

reduced to remind the driver to turn on the light.

Display overview

Depending on the equipment, the following informa-

tion is shown in the display.

Time

Selected gear/gear

recommendation

Also included de-

pending on vehicle

equipment:

▶ Compass direction

display

▶ Automatic gearbox

selector lever posi-

tions

▶ Detected road signs

Menu, indicator lights and information

Driver information system › Digital instrument cluster

Outside temperature

› Wait 4 seconds, the display shows the initial set-

ting.

- low outside temperature

Total distance travelled

The time is also set in the Infotainment in menu

Trip - Distance travelled after resetting the

memory

Setting the brightness of the instrument cluster

lighting

Overview of the main menu items

The brightness of the instrument lighting is adjusted

▶ Driving data » page 67, Overview

automatically according to the given lighting condi-

▶ Assist systems - Activate/deactivate assist sys-

tions.

tems

When low beam is switched on, the brightness of

▶ Navigation - e.g. Display driving recommendations,

the instruments lighting can be adjusted in the fol-

compass, list of destination

lowing menu in the Infotainment system:

▶ Audio - Using radio and media

▶ Telephone - Call list, accept or reject an incoming

call

Or:

▶ Vehicle - Vehicle condition » page 68, Display.

▶ Lap timer - Stopwatch » page 68, Usage.

Digital instrument cluster

Operation

Overview

Operation via the multifunction steering wheel

Overview of instrument cluster

Turn - Switch be-

tween menu

items/set values

Press - oÄfirm the

menu item

Press - Return to the

menu one level high-

Hold - Show main

menu

Press - Show previous menu (if one has been se-

lected) / Show telephone menu

Bar with indicator lights

Coolant temperature gauge

Settings

Fuel gauge

Display

Setting the language

Additional information

The language is set in the Infotainment in menu

Central display area

Resetting the odometer

NOTICE

› BrieĔû press the button in the instrument

Risk of serious damage to the engine and the ex-

cluster.

haust system!

▶ Never run the fuel tank completely empty!

Setting the time

Overview of the main menu items

› Press and hold the button in the instru-

▶ Driving data » page 67, Overview

ment cluster until the menu item Time is

displayed.

▶ Assist systems - Activate/deactivate assist sys-

tems

› Release the button, the display shows the hour set-

ting.

▶ Navigation - e.g. Display driving recommendations,

compass, list of destination

› Press the button repeatedly to set the hours.

▶ Audio - Using radio and media

› Wait 4 seconds, the display shows the minute set-

ting.

▶ Telephone - Call list, accept or reject an incoming

call

› Press the key repeatedly to set the minutes.

▶ Vehicle - Vehicle condition » page 68, Display.

Driver information system › Digital instrument cluster

▶

Lap timer - Stopwatch » page 68, Usage.

Set the variant of the display

› Press the button on the multifunction steering

wheel to change the variant of the display presen-

Operation

tation.

Rotate - Switch be-

Select displayed variants

tween menu

› Press and hold the button on the multifunction

items/Set values/

steering wheel.

Manually change

› Select and oÄfirm the menu item for the display

map scale

variants.

Press - oÄfirm the

› Select one of the following variants of the display

menu item

and oÄfirm.

Turn and press - Ac-

tivate automatic

map scale changing

Press - Return to the menu one level higher

Hold - Show main menu

Press - Change the variant of the display

Hold - Display the menu of preset options with

additional information

Settings

Setting the language

The language is set in the Infotainment in menu

Classic display

Advanced display

Resetting the odometer in the instrument cluster

Modern display

› Select Trip in the menu in instrument cluster display.

Basic display

Turn - Select infor-

Sporty display (depending on equipment)

mation

Press - oÄfirm in-

Choose display of additional information

formation

› Press and hold the button on the multifunction

Hold - Reset counter

steering wheel.

› Select and oÄfirm one of the following prefix op-

tions (the scope of the prefix options depends on

the type of Infotainment):

▶ Auto - Information depending on the selected

driving mode

Setting the time

▶ Classic - Information about the selected gear

The time is set in the Infotainment in menu

and the current speed

Setting the brightness of the instrument cluster

▶ Adjustable pre-selection options.

lighting

The brightness is adjusted automatically according

Setting the pre-selection option for the display of

to the given lighting conditions.

additional information

The pre-selection option for displaying additional in-

The brightness is adjusted with the dipped beam

formation is set in the Infotainment system in the

switched on in the infotainment in the following

following menu:

menu:

Menu item for the virtual cockpit

Or:

Menu item for the virtual cockpit

Driver information system › Driving data

Since start

▶ Driving data from the time of switching on the ig-

nition until the ignition is switched off again is stor-

ed in the memory. If the journey is interrupted for

more than 2 hours, the memory will be reset.

Long-term

▶ The driving data of all trips up to a total of 99

hours and 59 minutes driving time or 9999 km

driving distance is stored in the memory. If one of

the listed values is exceeded, the memory is reset.

› Select the desired additional information in the A

Since refuel

areas.

▶ Driving data from the time the fuel tank was last

› The desired function area for the preselection op-

filled is stored in the memory. The memory is reset

tion in the area B hold to save the selection (the

the next time the tank is filled.

scope of the preset options depends on the type

of Infotainment).

Operation

Driving data

Display driving data in the display of the instru-

ment cluster via the multi-functional steering

Overview

wheel

› Select the menu item for the driving data in the

The driving data display works with the ignition

main menu in the instrument cluster display.

switched on.

Rotate - Select in-

In the instrument cluster display

formation/Set values

Depending on the equipment, the display of the in-

Press - oÄfirm in-

strument cluster shows information such as speed,

formation

fuel consumption, range, etc.

In Infotainment

Displaying driving data in the infotainment system

The driving data is displayed in the following menu in

the infotainment system:

Menu item for driving data

Or:

Menu item for the driving data

Distance travelled

Select memory for driving data in the display of

Driving time

the instrument cluster via the multifunction steer-

Average speed

ing wheel and reset it

Average fuel consumption

› To select the memory

Evaluation of driving economy - Drive-

for the displayed driv-

GreenFunction (depending on Infotainment

ing data, press control

type) » page 173

wheel A repeatedly.

Graphical fuel gauge - If the expected range is

› To resetthe memory,

less than 300 km, the vehicle slowly approaches

hold the dial A .

the symbol

Range

Memory

The system saves the driving data in the following

Selecting the memory in the infotainment system

memories:

To select the memory, use the functional areas

in the following menu in the infotainment system:

Driver information system › Speed limit warning

Menu item for driving data

Vehicle status

Or:

Display

Menu item for the driving data

The vehicle status is displayed in the following menu

Resetting the memory in the infotainment system

in the infotainment system:

The memory is reset in the following menu in the in-

Menu item for the vehicle status

fotainment system:

Or:

Menu item for the vehicle status

Or:

Settings

Select driving data to be displayed

The driving data to be displayed is selected in the

following Infotainment menu:

Or:

Vehicle areas displayed in colour indicate associ-

ated warnings

Setting units

No ÄotifiatioÄ

The units are set in the following infotainment menu:

Warning messages regarding the vehicle con-

dition and their quantity

Or:

Display of information about the condition

of the START-STOP system

▶

Activation/deactivation of information

regarding the messages of the START-STOP

Speed limit warning

system in another screen display

Usage

The system offers the possibility to set a speed limit

Functionality

beyond which an acoustic warning signal will sound

In the event of a system fault, messages regarding

and the following warning message appears in the

the fault in question are displayed on the instrument

display of the instrument cluster.

cluster display when the ignition is switched on.

Messages in relation to faults can also be displayed in

Settings

the Infotainment.

The warning messages will continue to be dis-

Setting the speed limit

played until the malfunctions have been remedied.

› Select Warning at or

(depending on the display type)

After the first display of the message, only the indi-

and oÄfirm.

cator lights

(Hazard) or

(Warning) are dis-

› When the vehicle is stationary, set the desired

played.

speed limit and oÄfirm.

› While driving, drive at the desired speed and con-

firm it as the speed limit.

Stopwatch in the instrument cluster

Resetting the speed limit

Usage

› Select Warning at or

(depending on the display type)

and oÄfirm.

The function Laptimer offers the possibility to use up

› To reset the speed limit, oÄfirm the stored value.

to 11 lap times, e.g. when driving on a race track, to

If the journey is interrupted for more than 2 hours,

measure and display in the display of the instrument

cluster.

the set limit is deactivated, but the set value remains

stored.

Driver information system › Stopwatch in the Infotainment

Operation

› Select Lap timer in the main menu in the instrument

cluster display.

Displaying functions via the multifunction steering

wheel

Rotate - Select in-

formation/Set values

Press - oÄfirm in-

formation

Overall time

Start the measurement

Stop the measurement

Current lap time

Evaluate/reset split times

End the measurement (the current lap time is

Overview of functions

not stored)

▶ Start time - start the timing manually / continue

the interrupted measurement

Start measurement of the next lap time

▶ Since start - Start the timer automatically upon

The split time is brieĔû shown in the display A

start-up

End the measurement (the current lap time is

▶ Statistics - Evaluate and reset the measured times

stored)

▶ Fastest - the fastest lap

▶ Slowest - the slowest lap

▶ Average - the average lap time

Information Sport

▶ Overall time - the total of all the lap times

Settings

▶ Reset - reset all measured times

▶ New lap - Start measurement of the next lap time

The Sport information is displayed in the following

▶ Split time - show the split time

menu in the infotainment system:

▶ Stop - interrupt the time measurement

Sport

▶ Continue - Continue measurement of the current

Or:

lap time

Sport

▶ New lap - Start measurement of the next lap

A swipe of the fiÄ£er vertically across the screen al-

time

lows three of the following displays to be shown:

▶ Abort lap - cancel the time without saving the

measured time

▶ Charging pressure

▶ Exit - cancel the time and save the measured

▶ Acceleration

time

▶ Output

▶ Coolant temperature

▶ Oil temperature

Stopwatch in the Infotainment

Overview

Personalization

The stopwatch display is shown in the menu in the

Usage

Infotainment:

Sport

The personalization feature allows each vehicle key

to be assigned a user account.

Or:

In the user account, settings can be assigned regard-

Sport

ing e.g. light function, driver's seat and exterior mir-

ror position, assistance systems, radio, navigation,

etc.

Была ли эта страница вам полезна?

Да!Нет

4 посетителя считают эту страницу полезной.

Skoda Karoq (2021 year). Manual in english — page 3

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.