Skoda Kamiq (2021 year). Manual in english — page 2

Doors, windows and boot lid › Window - with electrical operation

once again and the window goes down by several

› Pull the corresponding button until it stops; the

centimetres.

window closes automatically. By pressing the but-

ton again, the closing process is stopped.

If you attempt to close the window again within

10 seconds of the window being moved down for

After switching off the ignition, the windows can

the second time, even though the obstacle was not

still open and close for about 10 minutes so long as

yet been removed, the closing process is only stop-

none of the doors are opened.

ped. During this time, it is not possible to automati-

Open all of the windows at the same time

cally close the windows by pulling the button all the

way. The force limiter is, however, switched on.

› Press and hold the button on the key.

Or:

The force limiter is only not operational if you at-

tempt to close the window again within the next

› Turn off the ignition, open the driver's door, and

10 seconds - the window will now close with full

hold down the driver's window button until it

force! If you wait longer than 10 seconds, the force

stops.

limiter is switched on again.

Close all of the windows at the same time

CAUTION

› Press and hold the button on the key.

Risk of injury!

Or:

▶ Close the windows carefully, even though they

have a force limiter.

› Turn off the ignition, open the driver's door, and

pull upwards on the driver's window button until it

stops.

Overview of the operating buttons on the

Or:

driver's door

›

For vehicles with a keyless locking system, hold

Depending upon vehicle

one fiÄ£eÙ on the sensor on the outside of the han-

equipment:

dle on the front door.

Front left window

Front right window

Settings

Rear left window

The window operation is set in the following menu in

the Infotainment system:

Rear right window

Menu item for window operation

Deactivation/activa-

tion of the buttons in

Or:

the rear doors

Menu item for window operation

Operation

Troubleshooting

When the windows are open, irritating noises

The window regulator has stopped working after

may occur at certain speeds.

repeated opening and closing

The window regulator mechanism could have over-

Opening

heated.

› Press the corresponding button slightly down-

wards and hold it until the window has reached the

› Allow the window regulator mechanism to cool

desired position.

down.

Or:

The window operation does not work after discon-

› Press the corresponding button until it stops; the

necting the 12 volt vehicle battery

window opens automatically. Pressing the button

› Enable window operation » page 28.

again will stop the opening process.

Closing

Activation after disconnecting the 12-volt

› To close, pull gently upwards on the top edge of

vehicle battery

the corresponding button and hold until the win-

dow has reached the desired position.

Activate automatic window operation

Or:

› Turn on the ignition.

› Pull the corresponding button upwards and the

window closes.

Doors, windows and boot lid › Sunblind - with electrical operation

› Release the button.

Boot lid - with manual operation

› Pull up the respective button and hold for 1 sec-

ond.

What you should be mindful of

NOTICE

Sunblind - with electrical operation

▶ Do not attach a bike rack to the tailgate.

Operation

Closing

Opening

› Press the handle and

› Press or hold the but-

lift the lid.

ton to move the roller

blind.

› Press or release the

button to stop the roll-

er blind from moving.

Activation after disconnecting the 12-volt

vehicle battery

The option to open by pressing the handle is deacti-

vated once a speed of 5 km/h is reached. This is acti-

› Turn on the ignition.

vated again after the vehicle has stopped and a door

› Keep the button pressed down. The sunblind

is opened.

opens and closes again.

Closing

› Release the button.

› Grasp the fixtuÙe A

and pull the lid down.

Sun visors

Folding up and folding down

CAUTION

Danger of opening the tailgate while driving!

▶ Make sure that the latch engages after the Ĕap is

closed.

Swivel the front visor towards the windscreen

Set a delayed lid lock

Swivel the visor towards the door

If the lid is unlocked with the

button on the key,

CAUTION

the lid is automatically locked again after closing.

Objects attached to the sun visors can restrict the

The period after which the lid is locked automatically

view to the outside.

can be extended by a specialist garage.

In the event of sudden braking or an impact, these

can also cause injuries.

▶ Do not attach anything to the sun visor.

Boot lid - with electrical control

What you should be mindful of

NOTICE

▶ Do not attach a bike rack to the tailgate.

Doors, windows and boot lid › Boot lid - with electrical control

Operation

Button in the door

› To open the tailgate,

CAUTION

pull and hold the but-

Risk of injury!

ton until the tailgate

▶ Only operate the tailgate when there is nobody or

starts to open.

no objects in the swivel area.

› To close the tailgate,

CAUTION

pull and hold the but-

Danger of opening the tailgate while driving!

ton until the tailgate is

▶ Make sure that the latch engages after the Ĕap is

fully closed.

closed.

› To stop the movement

NOTICE

of the tailgate, pull or

▶ Do not manually close the tailgate when moving.

release the button.

▶ Before operating the tailgate, check that there are

no objects in the swivel area that could damage the

Button on the key

tailgate. Also check that there are no objects with-

› Press the

button to

in the immediate vicinity of the vehicle that could

open, close or stop the

damage the vehicle interior and the transported

movement of the tail-

objects.

gate.

If the tailgate hits an obstacle when closing, it

The option to lock exists

stops and an audible signal sounds.

only on vehicles with a

When automatically closing the tailgate, e.g. un-

keyless locking system.

der the weight of snow, a broken beep sounds.

The key must not be in

the vehicle and must be

The rear parking light ĔashiÄ£ twice indicates

at a distance of max. 2 m

that the Ĕap is closed.

from the tailgate.

Handle in the tailgate

The tailgate can also be closed by pulling it bÙieĔû

› Press the handle to

downwards.

open, close or stop the

movement of the tail-

gate.

Settings

The option to open by

Set the uppermost position of the tailgate and

pressing the handle is

store it

deactivated once a

It makes sense to set the top position of the tailgate,

speed of 5 km/h is

e.g. setting for the opening of the tailgate in a limited

reached. This is activated

space due to the garage height.

again after the vehicle

has stopped and a door

› Stop the tailgate in the desired position.

is opened.

› Press the button and hold down on the lower

edge of the tailgate until an audible signal sounds.

Button in the tailgate

Re-adjusting the top starting position of the tail-

› Press the button to

gate

open, close or stop the

› Carefully raise the tailgate manually to the limit.

movement of the tail-

gate.

› Press the button and hold down on the lower

edge of the tailgate until an audible signal sounds.

Troubleshooting

The tailgate does not react to the opening signal

› There is a possible obstacle, e.g. snow; remove it.

Or:

› Press the handle in the tailgate and lift the lid.

Or:

› Mechanically unlock the Ĕap » page 31.

Doors, windows and boot lid › Unlocking the boot lid

The tailgate does not react to the closing signal

Seats, steering wheel and mirror

› Close the tailgate manually.

NOTICE

Front seat - with manual operation

▶ Close the tailgate slowly, push down the tailgate

Controls on the seat

and push in the lock on the centre of the rear edge

of the tailgate.

Unlocking the boot lid

Release

If the boot lid does not open, it can be unlocked

manually by the following procedure.

› Insert a screwdriver in-

to the opening in the

panel.

Adjusting the seat in the longitudinal direction -

› Release the tailgate by

after releasing the operating lever, the lock must

moving it in the direc-

audibly click into place

tion of the arrow.

Adjusting the height

Adjusting the angle of the backrest - do not lean

against the backrest during adjustment

Adjusting the lumbar support: Extent of the cur-

vature

After a certain time, play can develop within the ad-

justment mechanism of the backrest angle.

Folding passenger seat backrest

Folding down

› Pull on the operating

lever.

› Fold the backrest for-

wards until it clicks in-

to place.

Folding back up

› Pull on the operating lever.

› Press the backrest backwards until it audibly clicks

into place.

Seats, steering wheel and mirror › Front seat - with electrical operation

Front seat - with electrical operation

Folding down

› Press the release han-

Controls on the seat

dle and fold the seat

forwards.

Adjusting the seat

Adjust in a longitudi-

nal direction

Adjust the inclination

Adjusting the height

Folding back up

› Pull the outer seat belt

to the side trim.

Adjusting the seat back

› Fold the seat backrest

back up.

Adjust the inclination

The release handle must

audibly click into place.

› Check that the seat

backrest has locked in

place. The pin A must

not be visible.

Park position of rear seat belts

Adjusting the lumbar support

Set the position of

the curvature

Set the extent of the

curvature

Headrests

Rear seats

Adjusting the headrests

Folding down the seat backs

Front headrests

Before folding down

› Hold the safety button

› Insert the rear headrests as far as they will go or

remove them.

and move the headrest

in the desired direc-

› Adjust the position of the front seats in such a way

tion.

that they are not damaged by the folded-down

seat backrests.

› Pull the outer seat belt to the side trim.

Seats, steering wheel and mirror › Front armrest

Rear headrests

Rear armrest

› Move the headrest in

Settings

the desired direction.

When pushing down,

› Fold down the armrest.

press and hold the

The folded-down arm-

safety button.

rest can be used as a

storage table.

Removing and inserting the rear headrests

Removing

Steering wheel

› Partially fold the re-

spective seat back for-

Buttons/dials on the multifunction steering

wards.

wheel

› Move the headrest up

to the stop.

› Press safety buttons

A and B at the same

time and remove the

support.

Inserting

› Insert the headrest into the seat backrest.

The safety button must click into place.

Switch voice control oÄ/off

Front armrest

Heated steering wheel » page 53

Rotate - Adjust the volume

Settings

Press - Switch the sound off/oÄ

› Move the backrest to

Switch to the next track/station played

the desired position.

Switch to the previous track/station played

Show menu of assistance systems

Depending upon vehicle equipment:

▶ Operating an analogue instrument clus-

ter » page 55

▶ Operating a digital instrument clus-

ter » page 56

Depending upon vehicle equipment:

▶ Operating an analogue instrument clus-

ter » page 55

▶ Operating a digital instrument clus-

ter » page 56

Depending upon vehicle equipment:

▶ Operating an analogue instrument clus-

ter » page 55

▶ Operating a digital instrument clus-

ter » page 56

Seats, steering wheel and mirror › Interior rear-view mirror

Setting the steering wheel position

After switching off the ignition, it is then no longer

possible to switch on the ignition, to lock the steer-

WARNING

ing and to switch on the electrical components.

Risk of an accident!

Ĕashes

▶ Do not adjust the steering wheel while driving.

Message regarding a fault in the steering lock

› Swing the safety lever

› You may continue driving, exercising appropriate

downwards.

caution. Seek the help of a specialist garage.

Steering column lock not unlocked

Ĕashes

Message concerning the required steering

wheel movement

› Adjust the steering

› Move the steering wheel slightly back and forth.

wheel to the desired

› If the steering does not unlock, stop the vehicle

position.

and seek the help of a specialist garage.

Interior rear-view mirror

› Press the safety lever

Operation

as far as it will go.

Interior mirror with manual darkening

Mirror is not dark-

ened

Mirror darkens

Troubleshooting

Power assisted steering faulty

Interior mirror with automatic darkening

illuminates - total failure of the power assisted

Darkening of the mirror is automatically controlled

steering, failure of steering assistance

through the sensors in the mirror once the engine is

› Turn off the ignition, start the engine and drive a

started.

few meters.

CAUTION

› If the indicator light

does not go out, do not

Risk of an accident!

continue driving. Seek the help of a specialist ga-

A glowing display e.g. a mobile phone or navigation

rage.

device may affet the function of the automatic mir-

ror darkening.

illuminates - partial failure of the power assis-

▶ Do not attach these devices close to the mirror.

ted steering, possible reduction in power

steering

› Turn off the ignition, start the engine and drive a

Wing mirror

few meters.

Operation

› If the indicator light

does not go out, you can

drive on, exercising appropriate caution. Seek the

Depending on the equipment, the mirrors can be fol-

help of a specialist garage.

ded in manually or electrically.

Steering column lock faulty

Ĕashes

Message regarding a fault in the steering col-

umn lock

› Stop the vehicle.

› Seek the help of a specialist garage.

Seats, steering wheel and mirror › Wing mirror

Positions of the rotary knob

CAUTION

Risk of burns!

Adjust the left-hand

▶ Do not touch heated exterior mirror surfaces.

exterior mirror

Switch off operation

Adjust the right-

hand exterior mirror

Fold mirror in elec-

trically (to fold back

out, select a diffeÙ-

eÄt position)

Heat the mirror

when the engine is running

Adjusting the mirror surface

› Select position or .

› Turn the rotary knob in the direction of the arrows.

Folding electrically folding mirrors automatically

If this function is activated, the mirrors are folded in

when the vehicle is locked and folded back when it is

unlocked.

Locking of the vehicle is not indicated by the fact

that the mirrors fold in. Locking of the vehicle is indi-

cated by the turn signal lights ĔashiÄ£.

Manually foldable mirrors

› Fold the mirror towards the side window by apply-

ing pressure with your hand.

WARNING

Risk of an accident!

The exterior mirrors make objects appear farther

away.

▶ Use the rear-view mirror to determine the distance

from vehicles behind.

NOTICE

Danger of mirror damage!

▶ If the electrically foldable mirror is swung out by

external iÄĔueÄes (e.g. due to an impact during

manoeuvring), fold the mirror in using the rotary

knob and wait for an audible folding sound.

Settings

Automatic folding of the exterior mirrors is activated

or deactivated in the following menu in the Infotain-

ment system:

Or:

Troubleshooting

Electric mirror operation impaired

› Adjust the mirror surface by pressing it lightly with

your fiÄ£eÙ.

Restraint systems and airbags › Seat belts

illuminated - a front or rear seat belt is not fas-

Restraint systems and airbags

tened

Seat belts

lights up - rear seat not occupied

Functionality

illuminated - a rear seat belt is not fastened

Seat belts that are fastened correctly offeÙ very

good protection in the event of an accident. They re-

illuminated - a rear seat belt is not fastened

duce the risk of an injury and increase the chance of

survival in the event of a major accident.

illuminated - a rear seat belt is fastened.

WARNING

▶ The seat belts must not be removed or altered in

illuminated - a rear seat belt is fastened.

any other way.

▶ If the driver's seat belt is damaged, stop driving.

illuminated - a rear seat belt is fastened.

▶ If another seat belt is damaged, the seat must not

be occupied.

▶ Do not repair damaged seat belts yourself.

Operation

▶ Have a damaged seat belt replaced immediately by

a specialist garage.

Fastening the seat belt

Automatic belt retractor

› Grasp the buckle latch

The automatic retractor locks the belt in the event

and slowly pull the belt

of a jerky pull on the belt. The belts lock, for example,

over the chest and pel-

when full braking, when the car accelerates, when

vis towards the buckle.

driving downhill and when cornering.

› Insert the buckle latch

WARNING

into the buckle until

▶ If the seat belt does not lock when pulled jerkily,

there is an audible

have the retractor checked by a specialist garage.

click.

› Pull on the belt to en-

Belt tensioners

sure that the buckle is

The safety of the driver, front passenger and passen-

securely fastened.

gers on the outer rear seats who are wearing their

seat belts is enhanced by the belt tensioners fitted

Unfastening the seat belt

to the inertia reels on the front and rear external seat

› Grasp the buckle latch

belts.

and release it by press-

If there is a collision with a certain severity, the seat

ing the red button.

belt is tightened by the belt tensioner so that unwan-

› Hold the belt so it does

ted body movement is prevented.

not twist when rolling

The belt tensioner can also be deployed when the

up.

seat belt is not fastened.

Belt tensioners are not activated in the event of a

roll-over, minor collisions or in accidents in which no

major forces are produced.

Smoke is released when the belt tensioner is de-

ployed. This does not indicate a vehicle fiÙe.

Settings

Reversible belt tensioner

› Move the seat belt

Vehicles with a proactive occupant protection sys-

height adjuster up-

tem include reversible belt tensioners » page 141.

wards to increase the

height.

The reversible belt tensioners increase safety for the

belted driver and front passenger by automatically

tightening the seat belt tightly over the body in criti-

cal driving situations and then releasing it again.

Status display in the instrument cluster display

Depending on the type of display, the display can be

as follows:

Restraint systems and airbags › Child seat

› Press the safety button

tween the front seat and the child seat or the child

and move the seat belt

carried in the child seat.

height adjuster down

▶ Before installing a forward-facing child seat, adjust

to reduce the height.

the headrest so that it is as low as possible.

› After adjustment, fiÙm-

▶ If the headrest prevents the child seat from being

lû pull on the belt to

fitted, adjust the headrest to the highest position.

ensure that the seat

▶ When installing the child seat, avoid contact be-

belt height adjuster has

tween the roof and the rear pillar. If the head air-

correctly locked in

bag is deployed, there is a risk of injury.

place and that the belt

▶ If using a separate child seat cushion, adjust the

is locked securely.

headrest so that the child's head is Ĕush with, but

not protruding above the height of the top edge of

the headrest.

Troubleshooting

Blocked belt retractor

Using a child seat on the front passenger seat

› Grasp the strap in the

middle and pull quickly.

When using a child seat on the passenger seat, any

ouÄtÙû-speifi regulations must be observed.

› Hold the strap and let

it roll up slowly.

Never use a child seat in which the child is carried

› Pull on the strap to see

with his or her back to the direction of travel on a

if the retractor is

seat protected by an active airbag placed in front of

working properly.

the seat. This could cause serious injury to the child,

even death.

› If the strap is still

blocked, repeat the un-

This is also indicated by the following stickers:

locking procedure

once or twice.

› If the strap is still blocked, seek the help of a spe-

cialist garage.

Child seat

What you should be mindful of

For how to install and use the child seat, please note

Sticker on the passenger sun visor

instructions of the child seat manufacturer.

Sticker on the central body pillar on the passenger

For safety reasons, we always recommend that chil-

side

dren are transported on the back seats. Carry chil-

dren on the front passenger seat only in exceptional

The following instructions must be followed when

cases.

using a child seat on the front passenger seat:

Use child seats according to standard ECE-R 44 and

▶ It is essential to deactivate the front passenger air-

ECE-R 129 of the European Economic Commission.

bag if using a child seat in which the child is trans-

Child seats according to standard ECE-R 44 and

ported with its back facing the direction of trav-

ECE-R 129 are marked with the test symbol: large E

el » page 42.

in a circle, with the test number below.

▶ If possible, adjust the front passenger seat back-

We recommend using child seats from the ŠKODA

rest so that it is vertical, to ensure that there is se-

Original Accessories range. These child seats have

cure contact between the backrest and the child

been developed and tested for use in ŠKODA vehi-

seat.

cles. They satisfy the standard ECE-R 44 or ECE-R

▶ If possible, move the front passenger seat back-

129.

wards so that there is no contact between the

front passenger seat and the child seat behind it.

WARNING

▶ Adjust the height-adjustable front passenger seat

▶ When installing the child seat on the rear seat, ad-

as much as possible.

just the front seat so that there is no contact be-

▶ Set the front passenger seat belt as high up as pos-

sible.

Restraint systems and airbags › Fasteners for child seats

WARNING

without kinking and is not bent over the edge of

Risk of the seat belt causing a neck injury to the

the guide fittiÄ£.

transported child!

WARNING

▶ For child seats in groups 2 and 3, ensure that the

▶ As soon as the rear-facing child seat is no longer

guide fittiÄ£ attached to the child seat headrest is

being used on the front passenger seat, activate

positioned in front of or at the same height as the

the front passenger airbag again.

seat belt height adjuster on the central body pillar.

▶ Adjust the height of the front passenger seat belt

so that the belt passes through the guide fittiÄ£

Recommended child seats

Grouping of child seats according to standard ECE-R 44.

Group

Weight of the child

up to 10 kg

up to 13 kg

9-18 kg

15-25 kg

22-36 kg

Recommended child seats

Approval number

Group

Manufacturer

Type

Attachment

Order number

(E1 ...)

(up to 13

Britax Römer

Baby Safe Plus

Isofix base frame

1ST019907

04 301146

kg)

ISOFIX and TOP

Britax Römer

Duo Plus TT

DDA000006

04 301133

(9-18 kg)

TETHER

2-3

Britax Römer

Kidfix XP ^a)

ISOFIX

000019906K

04 301198

(15-36 kg)

Britax Römer

Kidfix II XP

ISOFIX

000019906L

04 301323

For optimum protection, especially in the event of a side impact, it is recommended that you use this child

seat complete with the backrest.

Fasteners for child seats

Use of child seats

Overview of usability of child seats according to standard ECE-R 16.

Restraint systems and airbags › Fasteners for child seats

Child seats with the ISOFIX system

Front passenger’s seat

Rear seats

Size category of

With deactiva-

Group

With activated

child seat ^a)

ted front airbag

Outer seats ^c)

Centre seat

front airbag ^b)

(up to 10 kg)

(up to 13 kg)

(9-18 kg)

IUF

(15-25 kg)

(22-36 kg)

The size category of the child seat is indicated on the child seat plate.

If the passenger seat is equipped with ISOFIX system holding eyelets, it is suitable for the installation of

an ISOFIX child seat with “Semi-Universal” approval.

The seat is suitable for the fixiÄ£ system ISO/R3.

IL The seat is suitable for the ISOFIX child seats with “Semi-Universal” approval.

IUF The seat is suitable for forward-facing child seats and is permitted for use in this weight category.

X The seat is not equipped with eyelets for the ISOFIX system.

i-Size

Front passenger’s seat

Rear seats

With activated front air-

With deactivated front

Outer seats

Centre seat

bag ^a)

airbag ^b)

i-U

If the passenger seat is equipped with the i-Size system, it is only suitable for i-Size children's seats that

are forward-facing and part of the “Universal” category.

If the passenger seat is equipped with the i-Size system, it is suitable for i-Size children's seats that are

forward- and backward-facing and part of the “Universal” category.

i-UF The seat is suitable for forward- and backward-facing i-Size child seats of the “Universal” category.

X The seat is not suitable for i-Size child seats of the “Universal” category.

Child seat fastened with a safety belt

When using a child seat of the “Universal” category on the middle rear seat, it is necessary to move the buckle

of the middle seat behind the buckle of the outer seat.

Correct position - the belt buckles are behind each

other

Incorrect position - the buckles are next to each

other

Restraint systems and airbags › Fasteners for child seats

Front passenger’s seat

Rear seats

Group

With activated front

With deactivated front

Outer seats

Centre seat ^a)

airbag

U ^b)

(up to 10 kg)

U ^b)

(up to 13 kg)

(9-18 kg)

(15-25 kg)

(22-36 kg)

It is forbidden to install a child seat with a support foot in the middle rear seat.

Adjust the height-adjustable front passenger seat as much as possible.

U The seat is suitable for the child seat category “Universal” and is permitted for use in this weight group.

UF The seat is suitable for forward-facing child seats in the “Universal”category and is permitted for use in this

weight group.

X The seat is not suitable for children in this weight group.

Overview

TOP TETHER

WARNING

ISOFIX

▶

Child seats with the TOP TETHER- Only use the

WARNING

system on the seats with the eyelets TOP TETH-

▶ On the retaining eyelets that are used to install the

ERSymbol are provided.

child seat with the ISOFIXSystem provided, do not

▶ Only attach one belt from the child seat to a lock-

attach any other child seats, belts or objects.

ing eye TOP TETHER-Fasten the system.

The ISOFIX system allows for the fast and secure in-

▶ When attaching the child seat with the TOP TETH-

stallation of the child seat. The eyelets for installing

ER- No other object may be attached to the eyelet

the child seat using the ISOFIX system are located

TOP TETHERSystem.

on the outer rear seats and possibly on the front pas-

senger seat.

A child seat that uses the ISOFIXsystem can only be

installed in the vehicle if it is approved for this vehi-

cle type. Further information can be obtained from a

ŠKODA partner or from a list of vehicles enclosed

with the child seat.

› Remove the covers be-

fore installing the child

seat.

Holding eyelets on the rear seats

Restraint systems and airbags › Airbags

The belt fastened into

In the following situations, no airbags are deployed:

the TOP TETHER system

▶ Minor frontal and side collisions

restricts the movement

▶ Rear-end collision

of the upper part of the

▶ Vehicle rollover

child seat.

If the measured deceleration rate is below the refer-

The holding eyelets for

ence values programmed into the control unit, the

attaching the belt are lo-

airbags will not be deployed despite possible serious

cated on the outer rear

vehicle damage.

seats, as well as on the

middle rear seat or pas-

Holding eyelet on the pas-

senger seat when neces-

senger seat

Airbag overview

sary.

The installation location of the airbags is marked

with the lettering

Airbags

Usage

The airbag system provides, as a supplement to the

seat belts, additional occupant protection during se-

vere frontal and side-on collisions.

The best possible protective effet of the airbag is

achieved only when the seat belt is also worn. The

airbag system is no substitute for the seat belts.

Front airbags

What you should be mindful of

Side airbags - front

Airbag systems can only properly protect if all occu-

Head airbags

pants have been secured and they are in the correct

seating position.

Side airbags - rear

No persons, animals or objects such as cup holders

Driver's knee airbag

or hangers for clothes may be in the deployment

WARNING

area of the airbags » page 41.

Danger of a functional restriction of the side airbags!

▶ Do not cover or stick anything over the steering

▶ Do not exert excessive forces, e.g. impacts, on the

wheel or the dash panel. The front airbags were

seat backs.

not able to deploy.

▶ Do not use seat covers that have not been ap-

The front passenger airbag should be switched off in

proved by ŠKODA.

some situations » page 42.

▶ Have damaged seat covers at the installation loca-

tion of the side airbags repaired by a specialist ga-

rage.

Functionality

Deactivating the airbags

When sinking into the iÄĔated airbag, the forward

We recommend having airbags other than the front

movement of the body is damped and the risk of in-

passenger airbag deactivated » page 42, Opera-

jury is reduced.

tionby a ŠKODA service partner.

As the airbags iÄĔate, smoke is released. This

Deactivation of the airbags should be considered in

does not indicate a vehicle fiÙe.

cases such as the ones below:

Airbag deployment in the event of an accident

▶ If the driver's seat adjustment is correct, the dis-

Airbag deployment is iÄĔueÄed by many factors.

tance of at least 25 cm between the centre of the

The deceleration rate at the time of impact is crucial.

steering wheel and the sternum cannot be main-

tained.

WARNING

Danger of serious or fatal injuries!

▶ Additional operating controls for a physically disad-

▶ Maintain the correct seating position.

vantaged driver are installed in the vehicle.

▶ Do not keep your limbs in the deployment area of

▶ The vehicle has special seats, e.g. orthopaedic

the airbags.

seats without side airbags.

Restraint systems and airbags › Key switch for the front passenger airbag

illuminates for 4 seconds after the ignition is

Operation

switched on and then Ĕashes for 12 seconds

Before switching off/sõitchiÄg on the front pas-

- Airbag or belt tensioner deactivated with the diag-

nostic device

senger airbag

Message regarding the deactivated airbag or belt

› Completely fold out the key bit.

tensioner

Switch front passenger front airbag oÄ/off

WARNING

› Switch off the ignition.

If an airbag is deactivated during the sale of the vehi-

› Open the passenger

cle, inform the buyer!

door.

› Insert the key bit into

the slot in the key

Requirements

switch as far as it will

✓ Ignition on

go.

› To Switch off, carefully

rotate the key switch

Troubleshooting

into the position

Airbag system faulty

› To Switch on, carefully rotate the key switch into

illuminates

the position

Message regarding an airbag fault

› Remove the key bit from the slot.

› Close the passenger door.

› Seek the help of a specialist garage.

› Turn on the ignition and check that the front pas-

senger airbag indicator lights are lit up.

Key switch for the front passenger

WARNING

airbag

When the passenger airbag is switched off, the head

airbag on the passenger side is also switched off at

Usage

the same time.

Deactivation of the front passenger airbag is provi-

Warning lights

ded for the following cases, for example:

▶ After switching on the igni-

▶ A rear-facing child seat is mounted on the front

tion, the two indicator lights

passenger seat.

light up bÙieĔû.

▶ The vehicle has special seats, e.g. orthopaedic

▶ If the system is OK, both of

seats without side airbags.

the indicator lights go out.

▶ The minimum distance to the control panel cannot

▶ One of the indicator lights then lights up again de-

be maintained.

pending on the position of the key switch:

lights up - front passenger airbag switched

What you should be mindful of

off

lights up 65 secs after the ignition is

WARNING

switched on - passenger front airbag

Danger of fault in the passenger airbag deactivation

switched on

system!

▶ Only switch off the airbag when the ignition is

switched off.

Troubleshooting

WARNING

Key switch for airbag deactivation is faulty

Danger of unexpected deployment of the passenger

Ĕashes together with

airbags in an accident!

The front passenger airbag will not be de-

▶ After switching off the passenger airbag with the

ployed in the event of an accident!

key bit, do not leave the key bit inserted in the key

switch while driving. Shocks can cause the Key as-

› Have the airbag system checked by a specialist ga-

signment to turn in the slot and trigger the airbag.

rage immediately.

Lighting, windscreen wipers and washers › Exterior lighting

illuminates

Lighting, windscreen wipers and

› Switch on the light.

washers

Exterior lighting

Operation

Functionality

Switching off the

Unless otherwise stated, the light works when the

lights except the

ignition is switched on.

daytime running

Daylight running lights

lights

The daytime running lights illuminate the area in

Switching the low

front of the vehicle.

beam oÄ/off auto-

matically

In vehicles for certain markets, this also provides

Switching on the

lighting for the rear area of the vehicle.

parking lights

Operating conditions

Switching on the low

✓ The lights switch is in position

beam

Switching the low beam oÄ/off automatically

As the basic position of the light switch, use posi-

The low beam is automatically switched on or off de-

tion

pending on the lighting conditions.

High beam and headlight Ĕasher

Operating conditions

The high beam works when the low beam is on.

✓ The light switch is in the

position.

Switch on high beam

The automatic headlight circuit is indicated by the il-

lumination of the symbol

in the light switch.

Switch off main

beam / switch on

Switching low beam on automatically in rain

headlight ĔasheÙ

Operating conditions

✓ The light switch is in the

position.

When the main beam or

✓ The function is activated.

headlight ĔasheÙ is

✓ The windscreen wipers are switched on for lon-

switched on, the indica-

ger than 30 seconds.

tor lamp lights up in the instrument cluster

The automatic headlight circuit is indicated by the il-

CAUTION

lumination of the symbol

in the light switch.

Risk of an accident!

▶

Do not dazzle other road users with the high beam.

Full LED Headlights

When the light switch is in position

, the head-

Turn signal

lights provide the best possible beam of light in front

Switching on the

of the vehicle. The Dynamic cornering light function

turn signal light on

ensures the best possible illumination of the curve

the right - the warn-

area.

ing light Ĕashes in

CORNER function

the instrument clus-

The CORNER function is intended for turning or ma-

ter

noeuvring (e.g. when parking).

Switching on the

turn signal light on

The function illuminates the vicinity of the vehicle

the left - the warn-

front in the direction of travel.

ing light Ĕashes in

Operating conditions

the instrument clus-

✓ The turn signal is switched on or the front wheels

ter

are steered sharply.

Turn signal - convenience signalling

✓ The low beam is switched on.

Convenience signalling enables three Ĕashes of the

✓ The fog lights are not switched on.

turn signal lights without having to move the lever

✓ The driving speed is lower than 40 km/h.

up or down.

When no light is switched on

› Tap the control lever up or down.

The symbol in the light switch may also light up in

The corresponding turn signal lights Ĕash three

the instrument cluster, indicating that it is necessary

times.

to switch on the light.

Lighting, windscreen wipers and washers › Exterior lighting

Tap the lever in the opposite direction ahead of

› Turn the light switch to position

time to stop signalling.

› Switch off the ignition.

Fog light

› Lock the vehicle.

When the parking light is switched on, an acoustic

Positions for pulling out

warning signal sounds after the ignition is switched

the light switch

off and the driver's door is opened. After a few sec-

Fog lights - when

onds or after the driver's door is closed, the warning

switched on, the in-

signal will stop.

dicator light in the

The light may switch off automatically if the 12-volt

instrument cluster il-

vehicle battery is too low. If the parking lights on

luminates

both sides are switched on with the ignition off, the

Rear fog light - when

lights will not be switched off automatically and the

switched on, the in-

12 volt vehicle battery may be discharged.

dicator light in the

instrument cluster illuminates

Settings

› Turn the light switch to position

› Pull the light switch to the appropriate position.

Activating/deactivating the automatic headlights

The rear fog light does not illuminate when an ac-

system in rain

cessory is connected to the trailer socket.

The function is activated or deactivated in the fol-

lowing menu in the Infotainment system:

Hazard warning light system

› Press the button to switch on or off in the mid-

dle part of the control panel.

Or:

The hazard warning lights can be switched on auto-

matically during hard braking. The hazard warning

Activating/deactivating convenience signalling

lights are then switched off again automatically

The function is activated or deactivated in the fol-

when starting off or accelerating.

lowing menu in the Infotainment system:

When the hazard warning system is on and the

turn signal is switched on, the hazard warning lights

will be switched off temporarily and only the turn

Or:

signal will Ĕash on the relevant side of the vehicle.

One-sided parking light

Headlamp levelling, LED headlights

The one-sided parking light allows one side of the

› Select the position of the control according to the

parked vehicle to be illuminated through activation

vehicle's current load status.

of the corresponding sidelights.

Front seats occu-

Switch on the side-

pied, boot empty

lights on the right

All seats occupied,

Switch on the side-

boot empty

lights on the left

All seats occupied,

› Switch off the ignition.

boot loaded

› Move the lever to the

Driver's seat occu-

appropriate position.

pied, boot loaded

› Lock the vehicle.

When the parking light is

For the Full LED headlights, the headlight range

switched on, an acoustic

control is adjusted automatically.

warning signal sounds and the driver's door is

opened. After a few seconds or after the driver's

WARNING

door is closed, the warning signal will stop.

Risk of an accident!

An incorrectly adjusted headlight range can cause in-

Double-sided parking light

suffiieÄt vehicle lighting or can dazzle other road

The two-sided parking light allows the parked vehi-

users.

cle to be illuminated through activation of the side-

▶ Adjust the headlight range correctly.

lights.

› Turn on the ignition.

Lighting, windscreen wipers and washers › COMING HOME, LEAVING HOME exterior lighting

Adjust headlights for driving in right / left-hand

COMING HOME, LEAVING HOME

traffic

exterior lighting

Applies to full LED headlights.

Functionality

› In Infotainment, select the following menu:

The COMING HOME function turns on the light after

turning off the ignition and opening the driver's door.

Or:

The light switches off automatically after the set

lighting time has elapsed.

› Activate the travel mode function.

The LEAVING HOME function switches on the light

when unlocking the vehicle with the wireless remote

control.

Troubleshooting

Turn signal light defective

Ĕashes faster - turn signal light on the right de-

Operating conditions

fective

✓ Visibility has worsened.

› Check the turn signal light on the right.

✓ The light switch is in the

position.

Ĕashes faster - turn signal light on the left de-

fective

Settings

› Check the turn signal light on the left.

This function is set in the following menu in the Info-

does not Ĕash when the trailer is hitched -

tainment system:

trailer turn signal light defective

› Check the trailer lighting.

Or:

Light bulb or LED bulb is defective

illuminates

Information appears in the display regarding

the defective lights.

Light Assist high-beam assist system

› Replace the defective bulb.

Functionality

› In case of a defective LED bulb, contact a specialist

garage for help.

The high beam assist system automatically switches

the high beam on and off.

The headlights are misted up on the inside

WARNING

Inside the headlights, moisture may occur. This is not

Risk of accident!

a defect.

▶ If necessary, manually switch the high beam on or

Malfunction of the automatic headlight circuit

off.

› Clean the windscreen in the area of the rain/light

sensor.

Operating conditions

Beam of light in front of the vehicle has shortened

Headlight defective.

✓ The system is activated.

› Seek the help of a specialist garage.

✓ The light switch is in the

position.

✓ The driving speed is higher than 30 km/h.

Driving lights defective

✓ The low beam is switched on.

If a message regarding the failed driving lights is dis-

played, the light will work in emergency mode.

› Drive on, exercising appropriate caution.

› Seek the help of a specialist garage.

Lighting, windscreen wipers and washers › Replace light bulbs

Operation

Conditions for changing a bulb

Switching on

✓ Ignition off

✓ Light switched off

› Push the lever in the

direction of the arrow.

It lights up in the instru-

Rear turn signal

ment cluster

from

the isolation box.

› Remove the cover with

the bracket from the

tool kit.

Switching off

› Manually switch the high beam on or off.

Function restriction

The system may dazzle other road users if their

headlights/lights are not detected for the following

reasons, for example:

› Unscrew screws A and

remove the lamp.

▶ The headlights/lights of oncoming vehicles are

covered by crash barriers, for example.

▶ The headlamps/lights of the oncoming or preced-

ing vehicle are dirty or not functioning.

Settings

Activation/deactivation

The function is activated or deactivated in the fol-

› Press the lock mecha-

lowing menu in the Infotainment system:

nisms on the connec-

tor and remove the

connector.

Or:

Activation/deactivation

The function is activated or deactivated as follows in

the Infotainment system in the menu

› Turn and remove the

socket with the bulb.

Replace light bulbs

What you should be mindful of

DIY replacement of the following bulbs is possible.

Have the remaining light sources replaced by a spe-

cialist garage.

The new bulb must conform to the speifiatioÄ of

the original light bulb. The name of the bulb is

marked on the bulb socket.

NOTICE

Danger of headlight damage due to the ingress of

water and dirt!

▶ Always fit the protective cap on the headlight cor-

rectly after changing a bulb.

Lighting, windscreen wipers and washers › Interior lighting

› Change the bulb in the

› Turn and remove the

socket.

socket with the bulb.

› Push the base with the

new light bulb into the

luminaire so that the

guide lugs on the base

and the associated

openings in the lumin-

aire are Ĕush.

› Turn the socket clock-

wise to secure.

› Change the bulb in the

› Insert the connector into the light until it clicks into

socket.

place.

› Push the base with the

new light bulb into the

luminaire so that the

guide lugs on the base

and the associated

openings in the lumin-

aire are Ĕush.

› Turn the socket clock-

wise to secure.

› Insert the cover cap until it clicks into place.

› Insert the lamp with the cones screws into the

Interior lighting

openings B in the body.

Operation

NOTICE

Risk of damage to the electrical system!

Switching on automatically

▶ Make sure that the lines between the lamp and the

The lighting switches on when one of the following

body are not pinched when the lamp is inserted.

events occurs.

› Screw on the lamp.

▶ The vehicle is unlocked

› Fit the cover of the light, ensuring it clicks into

▶ One of the doors is opened

place.

▶ The ignition key is removed (vehicle without start-

er button)

Reversing light

Automatic switch off

The lighting switches off when one of the following

› Open the boot lid.

events occurs:

› Release and remove

▶ The vehicle is locked

the cover cap in the

▶ The ignition is switched on

boot lid.

▶ About 30 seconds after all the doors have been

closed

Operation of the lighting

Middle

position

Automatically switch on and switch off

of the

switches

Turn the front and rear lights oÄ/off

Deactivation of automatic activation

Reading lamp left

Reading lamp right

Lighting, windscreen wipers and washers › Interior ambient light

If a door remains open and the ignition is switch-

Operation

ed off, the lights will turn off automatically after 10

minutes.

WARNING

Risk of an accident!

Automatic switching oÄ/off of the footwell light-

At low temperatures, windscreen washer Ĕuid can

ing

freeze on the windscreen and restrict visibility.

The lighting only works when the dipped or parking

▶ Only use the windscreen washer when the wind-

lights are on.

screen is warm.

The lighting is also switched on automatically after

Wipe and wash the windscreen

opening the door (e.g. when getting in or out).

Settings

The brightness level of the footwell lighting is set in

the Infotainment in the following menu when the

low beam or parking light is switched on:

Or:

Fast wiping

Slow wiping

Interior ambient light

Depending upon vehicle equipment:

Usage

▶ Intermittent wiping

▶ Automatic wiping controlled by the rain sensor

The ambient lighting ensures a comfortable atmos-

Switching off

phere in the vehicle interior.

Tip-wiping (spring-loaded position)

The lighting only works when the dipped or parking

lights are on.

Setting the wiping speed for the position

The lighting is also switched on automatically after

Washing and wiping (spring-loaded position)

opening the door.

The windscreen washer nozzles of the windscreen

are automatically heated together with the exterior

Settings

mirrors.

The background lighting brightness settings are set

Clean headlights

in the Infotainment system, in the following menu:

When the headlights are switched on, they are

cleaned the fiÙst time and after every tenth wash of

the windscreen. Setting the spray interval can be

Or:

carried out by a specialist garage.

Wipe and wash the rear window

Windscreen wipers and washers

Operating conditions

Operating conditions for windscreen wipers

✓ Engine compartment Ĕap closed

✓ Boot lid closed

✓ Ignition on

Operating conditions for the windscreen washer

system

Spring-loaded position:

✓ Engine compartment Ĕap closed

▶ Washing and wiping the windscreen

✓ Boot lid closed

▶ Cleaning the rear view camera

Wiping

Была ли эта страница вам полезна?

Да!Нет

2 посетителя считают эту страницу полезной.

Skoda Kamiq (2021 year). Manual in english — page 2

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.