Skoda Superb iV (2021 year). Manual in english — page 10
196 Wheels › Tyre pressure
Usage restrictions
Tyre pressure
Do not use the kit in the following cases:
What you should be mindful of
▶ The rim is damaged.
NOTICE
▶ The outdoor temperature is below the minimum
▶ Always adjust the tyre pressure to the load.
temperature indicated in the manual of the tyre fill-
▶ Check the pressure in all tyres at least once a
iģ bottle.
month and before each longer ride.
▶ Tyre punctures are greater than 4 mm.
▶ Check the pressure when the tyres are cold. Do
▶ There is damage to the tyre wall.
not reduce the higher pressure of warm tyres.
▶ The expiry date stated on the tyre iÄĔatioÄ bottle
▶ After each change in tyre pressure, save the new
has expired.
values in the tyre control display.
WARNING
Self-help
Risk of an accident!
▶ If tyre pressure loss is very quick, try to stop the
Seal the tyres
vehicle carefully without heavy steering or heavy
› Unscrew the valve cap from the damaged tyre.
braking.
› Unscrew the valve core with the valve insert and
place it on a clean surface.
Sticker with prescribed tyre pressures
› Shake the tyre iÄĔatioÄ bottle back and forth with
sealant.
The sticker with prescribed tyre pressures is located
› Screw the iÄĔatioÄ hose onto the tyre iÄĔateÙ bot-
on the inside of the fuel filleÙ Ĕap.
tle. The film on the closure is pierced automatically.
A
IÄĔatioÄ pressure for
› Remove the plug from the iÄĔatioÄ hose and push
half load
it fully onto the tyre valve.
B
IÄĔatioÄ pressure for
› Hold the bottle with the bottom facing upwards
a full load
and fill all of the sealing agent into the tyre.
C
Tyre diameter in in-
› Remove the filleÙ plug from the valve.
ches
› Screw in the valve insert.
This information only
IÄĔate tyres
serves as informa-
› Fit the tyre iÄĔatioÄ hose of the air compressor to
tion for the prescribed tyre pressure. This is not
the tyre valve.
a listing of approved tyre sizes for your vehicle.
› Secure the vehicle with the parking brake.
These are in the vehicle's technical documenta-
tion, as well as in the declaration of conformity
› Start the engine.
(in the so-called COC document).
› Plug the connector into the 12 volt socket .
D
Tyre pressure reading for the front axle tyres
› Turn on the air compressor.
› Once a tyre pressure of 2.0-2.5 bar is reached, turn
E
Tyre pressure reading for the rear axle tyres
off the air compressor.
Observe the maximum running time of the air com-
pressor according to the directions of the repair kit
Tyre pressure monitor
manufacturer.
Functionality
› If an air pressure of 2.0 - 2.5 bar has not been
reached, remove the tyre iÄĔatioÄ hose from the
The tyre pressure monitoring indicator indicates a
valve.
change in tyre pressure.
› Drive approx. 10 metres forwards or backwards to
Warning when pressure changes
allow the sealing agent to distribute in the tyre.
illuminates
› Replace the tire iÄĔatioÄ hose on the valve and re-
› Stop the vehicle.
peat the iÄĔatioÄ procedure.
› Check the tyres and tyre pressures.
Show tyres with modified pressure
› In the following menu, select the menu item for
displaying the tyre condition:
Or:
Wheels › Tyre pressure monitoring system 197
Tyre pressure monitoring system
Functionality
Function restriction
The system measures tyre pressure while driving us-
The system is unable to provide a warning in the
ing sensors on the wheels.
event of a very rapid tyre pressure loss, e.g. sudden
For correct system function, you must select the
puncture.
tyre type as well as the load condition of the vehicle
The system function may be restricted in the follow-
in the Infotainment.
ing cases:
After switching on the ignition, the last measured
▶ Uneven loading of the wheels, e.g. with a trailer at-
tyre pressure values are displayed. This display will
tached
be updated at the start of the journey.
▶ Sporty driving style
Warning when changing the tyre pressure
▶ Driving on dirt roads
illuminates
▶ Snow chains fitted
› Stop the vehicle.
› Check the tyres and tyre pressures.
Saving tyre pressure values
Store the tyre pressure values in the infotainment
Overview
› IÄĔate the tyres to the prescribed iÄĔatioÄ pres-
sure.
Display in the instrument cluster
› Turn on the ignition.
› Select Vehicle .
› In the following menu, select the menu item for
Display in Infotainment
displaying the vehicle condition:
› In the following menu, select the menu item for
displaying the vehicle condition.
Or:
Or:
› Using the functional surfaces
select the tyre
control display menu.
› Using the functional surfaces
choose the Tyre
› Tap on the functional surface
Pressure Monitoring menu item.
› Then follow the instructions on the screen.
Instrument cluster / Infotainment
Save the tyre pressures in the following cases:
▶ Change of tyre pressure
▶ Change of one or more wheels
▶ Change of position of a wheel on the vehicle
▶ Always after covering a distance of 10,000 km or
once a year
Troubleshooting
Tyre pressure display faulty
A
Tyre pressure
Ĕashes for about 1 minute and stays on
B
Recommended tyre pressure
› Stop the vehicle, switch off the ignition and
start the engine.
C
Tyre pressure not available
If the symbol Ĕashes again after starting the en-
D
Tyre pressure too low
gine, there is a system fault.
E
Adjust the vehicle’s loading condition
› Continue driving, exercising appropriate caution,
and seek the help of a specialist garage.
The tyres warm up while driving and there is an
increase in pressure. This is completely normal, it is
not a defect. If the system indicates an increase in
pressure while driving, do not reduce the pressure.
198 Wheels › Wheel bolt cover caps
Settings
Disconnecting
›
Hang the clamps for removing the wheel trims at
Tyre type
the edge of one of the openings in the trim.
Select the tyre type in the following menu.
› Push the wheel wrench through the clamp, support
on the tyre and pull off the wheel trim.
Or:
Installing
› Press the wheel trim onto the wheel rim at the
designated valve opening.
Vehicle loading condition
When using an anti-theft wheel bolt, it must be lo-
› In the following menu, select the menu item for
cated at the location indicated on the bezel.
displaying the vehicle condition.
Press the trim, starting at the valve, into the rim on
›
both sides until it engages around the entire cir-
Or:
cumference.
NOTICE
› Using the functional surfaces choose the menu
▶ Use hand pressure, do not hit the wheel cover.
item . Tyre pressure monitor .
› Tap the functional area and select the vehicle
Removing and installing the Aero trim
load condition.
Applies to factory built or original accessory trims
from ŠKODA.
Troubleshooting
Removal
Functional restriction / system fault
Ĕashes
› Stop the engine and start again.
› If the indicator light Ĕashes again after the engine
starts, there is a problem with the system.
› Continue driving, exercising appropriate caution,
and seek the help of a specialist garage.
Wheel bolt cover caps
›
Hook the bracket as close to the centre as possible
Remove cover caps and install
to remove the wheel covers at the edge of the
panel.
Disconnecting
› Pull off the centre of the wheel cover by loosening
› Push the pull-off clamp
it and pulling off the trim.
onto the cover cap up
To facilitate removal, it is possible to insert the
to the stop.
wheel wrench through the bracket loop and pull on
› Remove the cover cap.
the two key ends.
Installing
›
When using an anti-theft wheel bolt, it must be lo-
cated at the location indicated on the bezel.
› Position the panel on the wheel rim and push in the
individual spokes of the panel one after the other
Installing
until they are fully engaged.
› Push the cover cap onto the wheel bolt to the stop.
› Press in the centre of the wheel cover until it en-
gages completely.
NOTICE
Full wheel frame
▶ Use hand pressure, do not hit the wheel cover.
Removing and installing the trim
Applies to factory built or original accessory trims
from ŠKODA.
Storage space and interior equipment › Equipment in the boot 199
Fire extinguisher under the passenger seat
Storage space and interior
equipment
Equipment in the boot
Overview
Tool kit
Overview
Depending on the equipment, not all of the following
A
Lever for folding forward the rear seat backrests
components may be included in the tool kit.
B
Under the ĔooÙ covering: Storage compartment
for the charging cable
C
Net
Max. load 1.5 kg
D
Partition wall of storage compartment
Max. load 2.5 kg
E
12-Volt-power socket
Emergency equipment
A
Attachment for the anti-theft wheel bolts
Overview
B
Towing lug
C
Bracket for removing the full wheel covers
Emergency equipment in the luggage compart-
ment
D
Screwdriver
A
Tool kit
E
Removal clip for the wheel bolt cover caps
› To access the vehi-
F
Breakdown set
cle tool kit, fiÙst
fold the rear seat
The declaration of conformity is enclosed with the
on the right.
jack or the logbook folder.
B
Placing of the warn-
ing triangle
C
Placing of the fiÙst-
Storage compartment for the reĔective
aid kit
vest
Storage compartment for the reĔective vest
The storage compartment for the ÙeĔetive vest is in
the storage compartment of the front door.
200 Storage space and interior equipment › Fasteners in the boot
Fasteners in the boot
Cargo elements in the luggage
compartment
Overview
The maximum load for
the Cargoelements is
8 kg.
A
Bag hooks
Storage net
Max. load 7.5 kg
B
Fasteners for securing the fastening nets
The maximum permissi-
C
Lashing eyes for securing the load and the fas-
ble load for the net is 1.5
tening nets
kg.
Max. load 350 kg
Other fasteners
A
Cargo elements
Max. load 8 kg
A storage compart-
ment for the cargo
elements is located
under the ĔooÙ cov-
Fastening nets
ering in the boot.
Overview
› Fold up the cargo
element and fasten
The maximum load of
it to the ĔooÙ cov-
the respective fastening
ering in the boot.
nets is 1.5 kg.
Bag hooks in the boot
Multifunctional pocket
Operation
The maximum load for the multifunctional pocket is
3 kg.
The maximum load for the hook is 7.5 kg.
Storage space and interior equipment › Net partition 201
Unfolding
Net partition
› Fold down the front
Attach the net partition
hooks on both sides of
the boot.
Attach at the back
› Fit the rear strip on the
› Open the lid of the roll-
hooks.
up cover.
Folding
› Remove the rear strip
from the hooks.
› Place the rear strip
› Pull out the net parti-
against the front strip
tion.
and press them to-
› Insert the crossbar into
gether at both ends.
the mount on one side
and push it forwards.
› Fix the bar in the same
way on the other side.
› Open the lid of the
roll-up cover.
Removing and inserting
Fasten in the front
Removing
The procedure is analogous to the process behind.
› Remove the roll-up cover.
Before installing, fold back the rear seat backrests.
› Take out the folded pocket in an upwards direc-
tion.
Loosening
› Open the lid of the roll-up cover.
Inserting
› Move the rod fiÙst to one side and then to the oth-
› Insert the end of the
er side, and take it out of the supports.
strip marked with in-
› Hold the pole and allow the net partition to slowly
to the right-hand
roll in.
mount and the end of
› Open the lid of the roll-up cover.
the strip marked
with into the left-
hand mount.
Remove housing and insert
Removal
› Fold the rear seat backrests forwards.
› Open the door at the right rear.
› Move and swing out
the housing.
202 Storage space and interior equipment › Rigid boot cover
Inserting
Inserting
› Insert the housing into
› Insert the mount with
the supports and move
part A and then snap
it.
part B of the mount
into the recess C on
both sides of the boot.
› Hook in the retaining
straps.
Store the cover behind the rear seats
Troubleshooting
› Insert the cover behind
the rear seats.
Blocked net partition
› To unlock, press the
lock button.
Roll-up luggage compartment cover
Operation
Rigid boot cover
Extending
Removing and inserting
› Pull out the cover on
the handle until it clicks
The maximum load of the other fastening nets is
into place.
1 kg.
Removing
› Unhook the straps.
Retracting
› Press the cover in the
handle area.
The cover rolls up to
the intermediate posi-
› Hold the raised cover
tion A .
in place and press the
Press again to fully
underside of the cover
open the cover.
on both sides.
› Remove the cover.
It is possible that the
cover rolls more slowly
during winter weather
conditions.
Storage space and interior equipment › Through-loading bag 203
Settings
Automatic rewinding of the cover to the inter-
mediate position
The cover automatically rolls into the intermediate
position when the boot lid is opened.
The function is activated or deactivated in the fol-
lowing menu in the Infotainment system:
Or:
› Guide the securing strap B through the opening
around the upper part of the seat backrest.
› Fold the seat backrests back until the locking but-
ton clicks into place.
Removing and inserting
›
Insert the securing strap into the lock until it clicks
Take out and insert the roll-up cover
into place.
› Press the end of the
WARNING
crossbar and take out
The maximum weight of the transported skis is 17
or insert the cover.
kg.
NOTICE
Risk of damage to the armrest!
▶ Handle the bag and the skis with care.
Interior equipment front
Overview
Through-loading bag
Insert and lock
In the bag, a max. of 4 pairs of skis with poles can be
transported.
› Fold the rear armrest and the cover in the seat
backrest downwards.
› Place the empty bag in the opening in such a way
that the end of the bag with the zip is in the boot.
› Place the skis with the tips facing to the front and
the poles with the tips facing to the rear into the
bag and close the bag.
› Tighten the strap A
around the skis in front
of the bindings.
› Fold the seat backrest
a little forward.
A
Make up mirror
B
Ticket holder
C
Car park ticket holder
D
Glasses compartment
Max. load 0.25 kg
› To open, press the button.
204 Storage space and interior equipment › Interior equipment rear
E
USB-connection
Interior equipment rear
The USB connection is for charging only.
Overview
F
Storage compartment with air outlet nozzle
Max. load 3 kg
In the compartment, there is a card holder and a
pen holder.
› Pull the handle to open the compartment.
› Turn the knob to position to open the air
outlet nozzle.
G
Storage tray
▶ Bottle holder with a capacity of max. 1.5 l
▶ Storage compartment for the waste container
▶ Storage compartment for the ÙeĔetive vest
H
Storage compartment (depending on vehicle
equipment):
12-Volt power socket, USB connections, Phone-
box.
The USB connections can be used for charging
and for data transfer.
› Press the strip to open/close the compart-
ment.
I
Storage tray
A drinks holder is located in the compartment.
A
Coat hook
› Pull the strip to open the compartment.
Max. load 2 kg
J
Openable and adjustable armrest with storage
B
Storage pocket
compartment
C
Depending upon vehicle equipment:
There is a USB connection in the compartment.
The USB connection can be used for charging
▶ 230 volt socket and USB connections
and for data transfer.
The USB connections are for charging only.
› To open the compartment, lift the armrest.
▶ Storage compartment with 12 volt socket
› Turn the knob to position to open the air
D
Storage tray
outlet nozzle.
▶ Bottle holder with a capacity of max. 1.5 l
K
Storage tray
▶ Storage compartment for the ÙeĔetive vest
Max. load 0.5 kg
E
Storage pocket
A card holder is located in the compartment.
› Pull on the handle to open.
WARNING
▶ Only hang light clothing on the hooks. Do not leave
NOTICE
heavy and sharp objects in the pockets of the
▶ Do not leave any heat-sensitive objects in the
clothing.
spectacle compartment D.
▶ Do not use hangers to hang clothes.
Storage space and interior equipment › Storage pockets on the inner sides of the front seats 205
Storage pockets on the inner sides of the
Bottle tray in the storage compartment
front seats
of the front door
The tray is suitable for bottles with a max. size of 1.5
l.
Car park ticket holder
Bottle tray in the storage compartment
of the rear door
The tray is suitable for bottles with a max. size of 1.5
l.
206 Storage space and interior equipment › USB-connections
USB-connections
The USB connections are for charging only.
The USB connection is for charging only.
Hook on the centre body pillar
The USB connections can be used for charging and
for data transfer.
The maximum load for the hook is 2 kg.
WARNING
▶ Only hang light clothing on the hooks. Do not leave
heavy and sharp objects in the pockets of the
clothing.
▶ Do not use hangers to hang clothes.
Storage space and interior equipment › Glasses compartment 207
Glasses compartment
Storage compartment for cards, coins
and SD card
The maximum load for the compartment is 0.25 kg.
NOTICE
▶ Do not leave heat-sensitive objects behind in the
Storage compartment for cards in the
glasses compartment.
storage area on the driver's side
Pen holder
Storage compartment for an umbrella
Overview
208 Storage space and interior equipment › Phonebox
NOTICE
Troubleshooting
Risk of damage to the bodywork and the interior
A message has been displayed on the Infotainment
trim of the vehicle!
screen indicating that the mobile phone cannot be
▶ In the storage compartment, only insert the um-
charged.
brella from the ŠKODA original accessories.
▶ Always push the umbrella into the storage com-
▶ Check that there is no object between the support
partment as far as it will go.
and the phone to be charged. If this is the case, re-
move the phone and the item. Place the phone
centrally on the phone symbol on the pad again.
Phonebox
▶ Check that the position of the phone to be charged
has not changed. If this is the case, remove the
What you should be mindful of
phone and put it back in the centre of the phone
symbol on the pad.
CAUTION
Risk of burns during charging.
▶ The phone may get warm, remove it carefully from
Cup holder
the storage compartment.
▶ Do not leave any metal objects in the compartment
Overview
under the phone. If there is a metallic object in the
storage compartment, which has become hot, re-
Cup holder at the front
move the phone and let it cool down in the storage
› Press on the bar to
compartment!
open.
In the centre console
holder area, a bottle can
Functionality
be opened with one
Phonebox functions
hand.
▶ Wireless charging of phones.
› Press the bottle into
▶ AmplifiatioÄ of the telephone signal (only valid for
the holder and un-
some countries).
screw the cap.
The Phonebox is located in the storage compartment
Rear cup holder
in the centre console at the front.
Insert a telephone with a maximum size of 146x80
› To open it, open the lid.
mm into the storage compartment.
Charging Indicator
When the phone is charging, the in the status bar in
the infotainment screen will light up.
Recommendations for optimal function
▶ The phone is positioned with the screen facing up.
▶ Insert the phone without the protective case.
▶ Position the phone centrally on the phone symbol
on the pad.
CAUTION
Risk of scalding!
▶ Never put hot beverage containers in the drinks
Operating conditions
holder.
NOTICE
Conditions for wireless charging
Danger of damage to the electrical system and the
✓ The ignition is switched on.
panels from spilled drinks.
✓ The phone supports the Qi standard.
✓ There is no object between the pad and the
phone.
Storage space and interior equipment › Cup holder Easy Open 209
Cup holder Easy Open
Ashtray with removable insert
In the centre console
holder area, a bottle can
be opened with one
hand.
Cigarette lighter
› Push in the lighter.
Waste container
› Wait until the glowing
Replace bags
lighter pops back out.
› Remove the lighter and
use.
› Push the lighter back
in.
The socket of the ciga-
rette lighter serves as a
12-Volt socket.
Ceiling
Removing and inserting
Ashtray and cigarette lighter
The blanket is in a bag that can be attached to one of
the following locations:
What you should be mindful of
▶ On the guide rods of the front headrests
CAUTION
▶ In the storage pockets on the backs of the front
Risk of burning or fiÙe!
seats
▶ Do not use the ashtray for storing hot or burning
objects.
▶ Handle the lighter carefully.
Tablet holder
Settings
Operation
Tilt and turn
Removable ashtray
The ashtray is inserted in
the cup holder.
NOTICE
▶ When removing, do not hold the ashtray by the lid.
210 Storage space and interior equipment › Storage compartment for the tablet
Adjust size
› Press on the adapter
and remove it.
› Pull out the locking tab
and move the upper
part of the holder to
the desired position.
Set the minimum size of
the empty holder to
avoid noise while driving.
Insert into the rear armrest
› Clip the holder into the
opening.
Removal and Insertion
Fasten behind the headrests
› Place the open adapter
on the front guide rods
of the headrest and
clip in carefully.
Removal
› Press the safety button
and unfold the holder.
› Clip in the holder in the
adapter.
Technical data
Removal
The holder is for fixiģ a tablet with a height of min.
11.5 cm and max. 19.5 cm.
› Press the safety button
and unfold the holder.
The maximum load for the holder is 0.75 kg.
Storage compartment for the tablet
Operation
› Pull at the loop A to
open.
Storage space and interior equipment › 12-Volt power socket
211
12-Volt power socket
230 volt socket and USB connections
Operating conditions
NOTICE
Risk of damage to the electrical system of the vehi-
cle!
▶ Use the sockets only for the connection of ap-
proved electrical accessories with a total power
consumption of up to 120 watts.
NOTICE
Danger of damage to the connected consumers!
▶ Switch off the consumers before switching the ig-
nition on or off and before starting the engine.
230-Volt power socket
Functionality
NOTICE
Danger of damage to the connected consumers!
▶ Do not connect a light with ĔuoÙeseÄt lamp to the
socket.
▶ Switch off the consumers before switching the ig-
The USB connections are for charging only.
nition on or off and before starting the engine.
Status display
Storage compartment with air outlet
▶ Lit up in green - the socket is switched on.
nozzle
▶ Blinking green - the socket is still switched on for
about 10 minutes after the engine has been
Overview
switched off, if a consumer was connected before
the engine was switched off.
In the compartment, there is a card holder and a pen
holder.
The socket has a child safety lock. When insert-
ing the plug, the fuse is unlocked and the socket is
The maximum load for the compartment is 3 kg.
switched on.
› Turn the knob in the compartment to position to
open the air outlet nozzle.
Operating conditions
✓ Running engine
Troubleshooting
The indicator light Ĕashes red
The socket is turned off e.g. for the following rea-
sons:
▶ Excessive current
▶ Low state of charge of the 12-volt vehicle battery
▶ Overheating of the socket
› If the reasons given above no longer exist and the
socket is not switched on automatically, discon-
nect the connected load from the socket and re-
connect after a short time.
212 Roof rack and hitch › Roof rack
is coupled to the tow bar. The tow bar could be un-
Roof rack and hitch
locked.
Roof rack
CAUTION
Risk of injury!
Technical data
▶ Handle the trailer coupling carefully.
The maximum weight of the load incl. roof rack is
▶ When swinging out the tow bar, do not stand in
100 kg.
the middle area of the rear bumper.
NOTICE
Risk of damage to the trailer coupling!
▶ When not using the towing device, swing the tow
bar under the bumper.
Tow bar: swivel out/in
Swing out the tow bar
› Pull on the handle. The
tow bar swings out.
Depending on the equipment, the roof bars can be
The indicator light next
attached at the attachment points A and B or to
to the handle Ĕashes
the roof rail.
red.
› Slowly retract the han-
dle.
Swivelling hitch
What you should be mindful of
WARNING
› Press the tow bar until
An improperly installed or unsuitable tow hitch can
it audibly clicks into
damage the high-voltage components of the vehicle
place.
in an accident and thus deepen the consequences of
the accident or cause fatal injuries.
Check latching: the in-
▶ Due to the speifi structure of the vehicles with
dicator light next to
high-voltage batteries, we recommend using only
the handle lights up
the original ŠKODA tow hitch. With these accesso-
green.
ries, ŠKODA stands for safety, reliability and suita-
bility for this vehicle type.
▶ We recommend that all related assembly work be
carried out by ŠKODA service partners.
Swivel tow bar
NOTICE
Applies to natural gas vehicles.
▶ No trailer or any other accessory can be connected
WARNING
to the tow bar.
An improperly installed or unsuitable tow hitch can
▶ A socket or adapter may not be plugged into the
damage the natural gas reservoir of the vehicle in an
socket.
accident and thus deepen the consequences of the
accident or cause fatal injuries.
› Pull on the handle. The
▶ Due to the speifi structure of the vehicles with
tow bar is unlocked.
natural gas reservoirs, we recommend using only
The indicator light next
to the handle Ĕashes
the original ŠKODA tow hitch. With these accesso-
ries, ŠKODA stands for safety, reliability and suita-
red.
bility for this vehicle type.
› Slowly retract the han-
▶ We recommend that all related assembly work be
dle.
carried out by ŠKODA service partners.
WARNING
Risk of an accident!
▶ Do not manipulate the handle for swinging the tow
bar in and out while a trailer or another accessory
Roof rack and hitch › Swivelling hitch
213
› Swing in the tow bar
› Seek the help of a specialist garage.
under the bumper until
Tow bar not locked
it audibly clicks into
illuminates
place.
› Engage the tow bar.
Check latching: the in-
dicator light next to
the handle lights up
green.
Technical data
Tow hitch attachment points
Coupling or uncoupling a trailer or accessory
The following information describes the procedure
for coupling and uncoupling a trailer. The information
also refers to another accessory, e.g. a bike carrier.
WARNING
Risk of an accident!
▶ Do not use the safety eye for towing.
▶ Distribute and fix the load correctly.
The trailer has a 13-pin electrical socket. If the
trailer has a 7-pin connector, use a corresponding
adapter from the ŠKODA Original Accessories.
Coupling
› Swing out the tow bar.
› Put the trailer drawbar onto the ball head.
› Plug the electrical trail-
er plug into the socket
A.
› Hook the teaÙ-off rope
of the trailer onto the
A
Distance of the attachment points
safety eye B . The
B
Length of the rear overhang to the centre of the
teaÙ-off rope must sag
ball head
against the vehicle in
C
Distance of the front attachment point to the
all trailer positions.
centre of the ball head
Uncoupling
D
Distance of the rear attachment point to the
Uncoupling takes place in reverse order.
centre of the ball head
E
Distance of the rear bumper to the centre of the
Power supply of the trailer power network
ball head (according to the ECE-55 standard)
In the electrical connection between the vehicle and
trailer, the trailer is powered by the vehicle.
F
Distance from the centre of the ball head to the
road (according to the standard ECE-55)
NOTICE
Risk of damage to the vehicle electronics!
G
Fastening points on the body
The total power consumption of all consumers con-
nected to the trailer power supply must not exceed
In mm
350 watts.
A
1039.9
B
1196.2
Troubleshooting
C
564.2
D
344.2
Trailer coupling error
E
min. 65
The indicator light next to the handle does not light
F
350-420
up green, or the tow bar does not lock into place.
› Do not use the trailer coupling.
214 Maintaining and cleaning › Service events
Maximum vertical load for trailer operation
Maintaining and cleaning
The maximum vertical load for trailer operation de-
pends on the engine type and the vehicle equipment.
Service events
The valid speifiatioÄ for your vehicle can be found
service intervals
in the technical vehicle documentation, (e.g. vehicle
Compliance with service intervals is crucial for the
approval documentation, the COC document) or at a
life and value of the vehicle.
ŠKODA partner.
You will be Äotified of the due date for service with
Other information (e.g. on the nameplate of the trail-
the symbol and the corresponding message on the
er device) merely provides information on the test
display of the instrument cluster.
values of the device.
The specialist garage will inform you of the type of
Support load with mounted accessories
service interval, the option of changing this and the
When using the accessories (e.g. bicycle carrier), the
scope of service.
maximum length and the permissible total weight in-
cluding load must be considered.
All services and the replacement or ÙefilliÄ£ of op-
erating Ĕuids are chargeable to the customer, even
The maximum length of the mounted accessories
during the warranty period, unless the ŠKODA AUTO
(from the ball of the towing device) may not exceed
warranty conditions or other binding agreements de-
70 cm.
termine otherwise.
The permissible total weight of the mounted acces-
Proof of service
sories including its load corresponds to the maxi-
A specialist garage stores the proof of service in the
mum vertical load for trailer operation; the value can
information system called Digital Service Plan.
be found in the vehicle registration documentation.
The proof of service can be printed out.
If the maximum load in trailer operation is more than
75 kg, then the permissible total weight of the
Displaying the service due date in the Infotainment
mounted accessories including their load must not
system
exceed 75 kg.
› In Infotainment, select the following menu:
This value applies if the centre of gravity is at a dis-
Menu item for the Service
tance of no more than 30 cm from the towing device
Or:
ball head.
Menu item for the Service
If the distance of the centre gravity of the load to
the ball head of the towing device is greater than
Resetting information
30 cm, then the max. permissible total weight of the
We recommend that you do not reset the informa-
accessory, including its load, decreases (e.g. at a dis-
tion regarding service events on your own. It can
tance of 60 cm from the ball head, the permissible
lead to incorrect setting of the service intervals and
weight decreases by half).
thus also to possible faults in the vehicle.
If the distance between the centre of gravity of the
For vehicles with a variable service interval, new
load and the ball head of the towing hitch is 70 cm,
service interval values calculated according to the
the permissible total weight of the accessories in-
previous operating conditions will be displayed after
cluding their load is reduced to 0 kg.
the oil change service indicator is reset. These values
WARNING
will then continue to be adjusted according to the
current operating conditions.
Risk of an accident!
▶ Do not exceed the maximum vertical load.
▶ The permissible trailer load and the weight of an-
Service work, adjustments and technical
other accessory, e.g. of the bike carrier, is not to be
exceeded.
changes
NOTICE
The instructions and guidelines from ŠKODA AUTO
Risk of damage to the trailer and the vehicle itself!
must be observed when carrying out any modifia-
▶ When using the accessory (e.g. bicycle carrier), ob-
tioÄs, repairs or technical alterations to the vehicle.
serve the maximum length and the permissible to-
Adhering to these instructions and guidelines helps
tal weight of the accessory incl.
ensure road safety and helps keep the vehicle in a
good technical condition.
We advise only using ŠKODA Original Accessories
and ŠKODA Original Parts which have been expressly
approved for use on your vehicle. Reliability, safety
Maintaining and cleaning › Interior 215
and suitability for your vehicle are guaranteed with
non-legitimate installation in another vehicle (e.g. af-
these.
ter a theft) or operation outside the vehicle.
ŠKODA Service partner
All ŠKODA service partners work according to the
Interior
instructions and guidelines from ŠKODA AUTO.
Service and repair work is therefore carried out on
What you should be mindful of
time and at the appropriate quality. Adhering to
these instructions and guidelines helps ensure road
NOTICE
safety and helps keep the vehicle in a good technical
▶ Use cleaning agents intended for cleaning and care
condition.
of the individual materials.
▶ Do not use aggressive cleaning agents or chemical
We therefore advise having all modifiatioÄs, repairs
solvents.
and technical alterations to the vehicle carried out by
a ŠKODA Service Partner.
Natural leather / Faux leather / Alcantara ® / Sue-
ŠKODA original parts
dia / material
We recommend the use of ŠKODA Genuine Parts for
NOTICE
your vehicle, as these parts are approved by ŠKODA
▶ Remove impurities as soon as possible.
AUTO. These parts comply wholly with ŠKODA AU-
▶ Do not use solvents, ĔooÙ wax, shoe cream, stain
TO regulations and are identical to the parts used in
remover or similar agents on Alcantara® and Suedia
series production.
suede seat upholstery.
ŠKODA AUTO is able to warrant the safety, suitabili-
▶ Make sure that natural leather is not moistened
ty, and long life of these products.
when cleaning and that no water seeps into the
ŠKODA Service Partners are liable for any defects of
seams.
ŠKODA Genuine Parts for a period of 2 years after
▶ Do not clean the roof cladding with a brush.
sale in accordance with the materials defect liability,
NOTICE
unless agreed otherwise in the purchase agreement.
Risk of fading to the cover fabric!
ŠKODA original accessories
▶ If necessary, do not leave the covers for long peri-
We recommend that you use ŠKODA Genuine Ac-
ods in the blazing sun.
cessories in your vehicle. With these accessories,
ŠKODA AUTO stands for safety, reliability and the
▶ During use, the leather and Alcantara®- and Suedia
suitability for your vehicle type.
and materials may show minor changes (e.g. folds
ŠKODA Service Partners are liable for any defects of
or discolouration). This does not constitute a mate-
ŠKODA Genuine Accessories for a period of 2 years
rial defect.
after installation or delivery in accordance with the
▶ Some clothing fabrics, e.g. dark denim, sometimes
materials defect liability, unless agreed otherwise in
do not have suffiieÄt colour fastness. As a result,
the purchase agreement or any other agreements.
discolouration that is clearly visible on the seat up-
holstery can occur. This is not a defect in the fab-
Spoiler
ric.
WARNING
▶ Sharp-edged zippers, rivets, clamps and similar
Risk of an accident!
garments can damage the upholstery in the vehi-
▶ Only use the original spoiler on the front bumper in
cle. Such damages cannot be subsequently recog-
combination with the original spoiler on the boot
nised as a justified complaint.
lid.
Plastic parts
▶ The original spoiler on the front bumper cannot be
left on its own without the spoiler on the luggage
NOTICE
compartment lid or in combination with an unsuita-
Risk of damaging the dash panel!
ble spoiler on the luggage compartment lid.
▶ Do not attach fragrances and air fresheners to the
▶ We recommend that you consult the ŠKODA Serv-
dash panel.
ice Partner for any repairs to or replacement, addi-
Windows
tion or removal of spoilers.
NOTICE
Component protection
Risk of damage to the filameÄts or the glass antenna!
Some electronic vehicle components (such as the in-
▶ Do not stick stickers on the heating filameÄts.
strument cluster) are factory-equipped with compo-
▶ Do not use sharp objects (such as pot scrapers,
nent protection. This component protection ensures
etc.) to clean the windows.
the functional limitation of these components in a
216 Maintaining and cleaning › Exterior
Covers on electrically heated seats
Exterior
NOTICE
What you should be mindful of
Risk of damaging the heating system!
▶ Do not clean the seats with water or other liquids.
WARNING
▶ Do not dry the seats by switching on the heating.
Risk of accident!
After washing the vehicle, the functionality of the
Seat belts
brake system may be affeted by moisture and, in
NOTICE
winter, by ice.
Risk of damage to the seat belts!
▶ Dry and clean the brakes by braking several times.
▶ Do not dry clean the seat belts.
NOTICE
▶ Allow cleaned belts to dry before rolling up.
▶ Bird droppings, insect residues, litter and sea salt
residues, oveÙĔoõed fuel etc. are to be removed as
soon as possible.
Instructions for cleaning
▶ Do not use rough sponges, scourers or similar to
Natural leather / Faux leather / Alcantara ® / Sue-
remove dirt.
dia / material
▶ Use cleaning agents intended for cleaning and care
› Remove dust and dirt on the surface with a vac-
of the individual materials.
uum cleaner.
▶ Do not use aggressive cleaning agents or chemical
› Remove fresh impurities with water, slightly mois-
solvents.
tened cotton cloth or woollen cloth; if necessary,
▶ Do not polish the vehicle in a dusty environment.
use a mild soap solution 1) and wipe with a dry
NOTICE
cloth.
▶ Paint damage should be repaired as soon as possi-
› Remove stubborn stains with a suitable cleaning
ble.
agent.
▶ Do not treat matt lacquered parts with polish or
› For regular care of natural leather, use the equip-
hard wax.
ment provided for this purpose. After each clean,
▶ Do not polish foils.
use a care cream with light protection and impreg-
▶ We recommend treating door seals and window
nation effet.
guides with the appropriate tools from ŠKODA
› When looking after Alcantara®-, Suedia and and
original accessories. These ensure that the protec-
fabric surfaces, remove stubborn hair with a clean-
tive lacquer layer of the seals and window guides is
ing brush. Remove pills from materials with a
not attacked.
brush.
▶ Do not use abrasive cleaning agents to clean the
Plastic parts
rear view camera.
› Remove impurities with water, slightly moistened
Before driving through a car wash
cloth or sponge with a suitable cleaning agent if
› Observe the usual speifiatioÄs of the car wash,
necessary.
e.g. close all windows, fold the mirrors, etc.
Windows
› Move the windscreen wiper lever to position
› Remove impurities with clean water and dry with a
to adjust.
cloth provided for this purpose.
› If there are special attachments on your vehicle,
Infotainment screen
observe the instructions of the car wash operator.
› Remove any impurities on the screen using the
NOTICE
cleaning agents provided.
▶ Deactivate the Auto Hold function if it is necessary
to roll the vehicle when passing through a car
NOTICE
Danger of screen damage!
wash.
▶ When removing dirt, do not press on the screen.
NOTICE
In vehicles with an electric luggage compartment lid,
Covers on electrically heated seats
this can open automatically due to the pressure of
› Remove impurities with a suitable cleaning agent.
the washing brushes.
Seat belts
▶ Lock the vehicle, e.g. with the central lock button.
› Remove impurities with a soft cloth and mild soap
solution.1)
1)
A mild soap solution consisting of 2 tablespoons of white neutral soap to 1 litre of lukewarm water.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст