Skoda Kodiaq (2021 year). Manual in english — page 9
Starting and driving › Towing eye and towing procedure
175
Engine type
Gearbox
Permissible trailer load,
Permissible trailer load, un-
braked (kg) a)
braked (kg)
Five-seat
Seven-seat
Five-seat
Seven-seat
version
version
version
version
2.0 l/147 kW TDI CR
DSG b) 4x4
2300
2000
750
750
2.0 l/176 kW TDI CR
DSG b) 4x4
2300
2000
750
750
a)
With gradients up to 12%.
b)
Automatic dual-clutch transmission.
Towing eye and towing procedure
Towing the vehicle
Towing lug
WARNING
Risk of accident!
Removing the grille
▶ The tow rope must not be twisted.
› Insert the clamp for
▶ When towing, drive at a speed of max. 50 km/h.
taking off the full
wheel trims in the re-
cess in the grille, and
remove the grille.
Removing the rear cap
› Press on the cap and
WARNING
remove it.
Risk of accident!
▶ Use a braided synthetic fibre rope for towing. Do
not use a twisted tow rope.
NOTICE
▶ Always keep the tow rope taut during towing.
▶ Do not exceed a towing distance of 50 km.
NOTICE
Danger of gearbox damage!
▶ If the gearbox no longer contains any oil, the vehi-
Installing the towing eye
cle must only be towed with the front axle raised
› Screw in the towing
clear of the ground or transported on a special
eye.
breakdown vehicle.
› Insert the wheel
▶ Vehicles with automatic transmission must not be
wrench or similar ob-
towed without the ignition switched on or with the
ject through the tow-
rear axle raised.
ing eye.
Where should the tow rope or the tow bar be se-
› Tighten the towing
cured?
eye.
▶ At the front towing eye
▶ At the rear towing eye
▶ On the ball bar of the factory-installed towing
After the towing process
hitch
› Unscrew the towing eye.
› Insert the cover or grille.
For vehicles with fatorû-fitted towing device, at
the back there is no mount for a screw-in towing
eye.
Information for the driver of the towing vehicle
› Drive slowly and smoothly.
176 Starting and driving › Brakes
› Only accelerate once the rope is taut.
recommend checking the brake Ĕuid level regularly
directly at the reservoir.
Information for the driver of the towed vehicle
› Move the shift lever to the neutral position or the
WARNING
selector lever to the position.
Danger of brake failure!
If the Ĕuid level falls si£ÄifiaÄtlû within a short time
› If it is not possible to start the engine, switch on
or drops below the mark
, the brake system may
the ignition!
have become leaky.
WARNING
▶ Stop driving! Seek the help of a specialist garage.
Risk of accident!
When the ignition is switched off, the brake booster
SpecificatioÄ
and the power steering do not work. In addition,
The brake Ĕuid must comply with standard
there is a risk that the steering lock will engage.
VW 501 14. This standard complies with the re-
▶ If it is not possible to start the engine, switch on
quirements of the FMVSS 116 DOT4 standard.
the ignition!
Changing
Have the brake Ĕuid replaced by a specialist garage.
Brakes
WARNING
Danger of brake failure!
What you should be mindful of
If the brake Ĕuid change date is exceeded, heavy
braking may cause vapour bubbles to form in the
WARNING
brake system.
Problems and faults with the brake system can ex-
tend the braking distance of the vehicle!
DANGER
Troubleshooting
Danger of a functional restriction of the brake boos-
Brake Ĕuid level is too low
ter!
illuminates
▶ When braking in a vehicle with manual transmis-
sion, when the vehicle is in gear and at low revs,
› Stop driving! Seek the help of a specialist ga-
depress the clutch pedal.
rage.
DANGER
Brake system and anti-lock braking system faulty
Danger of the brakes overheating!
illuminates together with
▶ Do not depress the brake pedal unless braking is
› Stop driving! Seek the help of a specialist ga-
required.
rage.
▶ If the original front spoiler is damaged, ensure the
air supply to the front brakes is guaranteed.
Worn brake pads
illuminates
Inspecting the brake Ĕuid level
› Drive to a specialist garage, exercising ap-
propriate caution.
Test conditions
✓ The vehicle is on a horizontal surface
Reduced braking effect
✓ The engine is off
Damp, frozen, salt-affeted or corroded brakes can
impair the braking effet.
Checking
›
Clean the brakes by braking several times if traffi
The fill level must be
conditions allow it.
within the marked range.
When the engine is stopped, the brake booster
› If the level is below the
does not work
mark
, do not con-
› Depress the brake pedal more forcefully.
tinue.
› Do not refill liquid.
› Seek the help of a spe-
Electric parking brake
cialist garage.
Operation
If the brake Ĕuid level is
too low, this will be indi-
WARNING
cated in the instrument cluster by the illumination of
Danger of key locking!
is displayed in the status bar. Nevertheless, we
▶ The recessed grip for the fiÄ£ers in front of the
button must remain empty.
Starting and driving › Auto Hold automatic holding function 177
Manual switch on
Emergency braking in case of faulty brake
› Pull the button and
system
hold it.
Switching on
The following symbols
› Pull the button and
light up.
hold it.
▶ in the button.
The vehicle starts to
▶ in the instrument
brake sharply and an
cluster.
acoustic signal is soun-
ded.
Automatic shut-off
The parking brake switches off automatically when
starting up.
Switching off
If automatic sõith-off is to be prevented, e.g. when
› Release the button
starting off on a slope, keep the button pulled.
Or:
Conditions for automatic shutting down
✓ Driver's door is closed, in some cases, the driver's
› Depress the accelerator pedal.
seat belt is also fastened
Manual shut-down
Auto Hold automatic holding function
› With the ignition
Usage
switched on, press the
brake pedal and at the
Auto Hold automatically secures the vehicle from
same time push the
rolling away when stopped.
button.
Functionality
WARNING
Risk of an accident!
Auto Hold is not able to stop the vehicle under all cir-
cumstances, such as on slippery ground, or on gradi-
Troubleshooting
ents.
Parking brake error
Secure and release the vehicle
With Stop, the vehicle is automatically secured us-
illuminates
ing Auto Hold. lights up in the instrument cluster.
The brake pedal can be released.
Message regarding a parking brake error
With Start, the vehicle is automatically released us-
› Seek the help of a specialist garage.
ing Auto Hold.
Parking on a steep slope
Automatic protection from the parking brake
Ĕashes
Under certain circumstances, the vehicle can be se-
cured using the parking brake. lights up in the in-
NotifiatioÄ regarding parking position on a steep
strument cluster.
slope
› Go to another parking spot where there is less of a
slope.
Operating conditions
Noise when using the parking brake
✓ The driver's door is closed.
Noise when using the parking brake is normal. This is
✓ The engine is running or has been switched off by
not a defect.
the START-STOPP system.
The 12 volt vehicle battery is discharged, the park-
✓ Auto Hold is activated.
ing brake cannot be switched off
✓ On vehicles with an automatic gearbox, the selec-
› Connect the 12 volt vehicle battery to a power
tor lever is not in mode.
source, such as the 12 volt vehicle battery of an-
other vehicle.
178 Driver assist systems › Braking and stabilising systems
Settings
Driver assist systems
Activation/deactivation
Braking and stabilising systems
› Press the
button.
Activation is indicated by the illumination of the
Overview
symbol in the button.
Stabilisation control (ESC)
NOTICE
ESC helps to stabilize the vehicle in borderline situa-
Disable Auto Hold to allow the vehicle to roll if nec-
tions (e.g. when the vehicle starts to skid). ESC
essary when driving through a car wash.
brakes the individual wheels to maintain the direc-
tion of travel.
Ĕashes - ESC is engaged
ESC Sport
ESC Sport allows for a sportier driving style.
lit up - ESC Sport is activated
Traction control (TCS)
ASR helps to stabilize the vehicle when accelerating
or driving on low-grip roads. ASR reduces the drive
power transmitted to the wheels when the wheels
spin.
Ĕashes - ASR is engaged
Antilock braking system (ABS)
ABS helps maintain control of the vehicle during
emergency braking. An ABS intervention is noticea-
ble by pulsating movements of the brake pedal.
Motor Slip Regulation (MSR)
MSR helps to maintain control of the vehicle in the
event of a sudden reduction in speed, e.g. on icy
roads. If the drive wheels lock, MSR increases the
engine speed. This reduces the braking effet of the
engine and the wheels can rotate freely again.
Electronic DiffereÄtial Lock (EDL)
EDL helps to stabilize the vehicle when driving on
road surfaces with differeÄt grip under the individual
wheels. EDL brakes a spinning wheel and transmits
power to a differeÄt drive wheel.
Electronic DiffereÄtial Lock (XDL+)
XDL + helps to stabilize the vehicle during fast cor-
nering by braking the inside wheel of the driven axle.
Active steering assistance (DSR)
In diffiult situations, the DSR provides the driver
with a steering recommendation in order to stabilise
the vehicle.
Hill Hold Control
Hill Hold Control helps when starting off on uphill
gradients by braking the vehicle for about 2 seconds
after the brake pedal is released.
Operating conditions
✓ The gradient is at least 5%.
✓ The driver's door is closed.
Driver assist systems › Front Assist 179
Multi-Collision Brake (MCB)
Troubleshooting
MCB helps to decelerate and stabilize the vehicle af-
ESC or ASR faulty/deactivated by the system
ter a collision with an obstacle. This reduces the risk
of further collisions.
illuminates
Operating conditions
› Stop the engine and start again.
✓ There has been a frontal, side and rear collision of
› If the indicator light does not go out after covering
a certain severity.
a short distance, seek the help of a specialist ga-
✓ The impact speed was greater than 10 km/h.
rage.
✓ The brakes, ESC and other required systems re-
ABS faulty
mained functional after the impact.
illuminates
✓ The accelerator pedal is not pressed.
›
You may continue driving, exercising appro-
Trailer Stability Assist (TSA)
priate caution. Seek the help of a specialist garage.
TSA helps to stabilize the trailer. As the trailer begins
to lurch, TSA stabilizes the trailer by slowing down
Brake system and anti-lock braking system faulty
the individual vehicle wheels.
illuminates together with
Operating conditions
› Stop driving! Seek the help of a specialist ga-
✓ The hitch was supplied from the factory or pur-
rage.
chased from ŠKODA Genuine Accessories.
✓ The trailer is connected to the trailer socket.
✓ ASR activated.
Front Assist
✓ The driving speed is higher than 60 km/h.
Functionality
Front Assist monitors the distance to the vehicle
Settings
ahead and points out when the safety distance is ex-
Deactivating/activating ASR
ceeded. In borderline situations, it helps to avoid a
› Press the button.
collision by braking interventions.
Or:
Status display in the instrument cluster display
illuminates - safety distance too small
› In Infotainment, select the following menu:
or
illuminates - warning in case of collision
Or:
Automatic braking if there is a risk of a collision
If there is a risk of a collision, the following symbol is
When deactivated, lights up in the instrument
cluster.
illuminated as a warning
or
from the isolation
box. If you do not respond to the warning, the vehi-
goes out on renewed activation.
cle will slow down.
Deactivating the ASR may be helpful in the following
At a driving speed of up to 30 km / h, the vehicle is
situations:
braked without prior warning.
▶ Driving with snow chains
Automatic braking can be stopped by pressing the
▶ Driving in deep snow or on very loose ground
accelerator pedal or by a steering intervention.
▶ Starting up a vehicle that is stuck
With automatic braking, the pressure in the brake
Activate/deactivate ESC Sport
system increases. The brake pedal cannot be operat-
› Keep the button pressed down.
ed by using the pedal as normal.
Or:
WARNING
› In Infotainment, select the following menu:
Risk of an accident!
Front Assist does not respond to crossing or oncom-
ing vehicles.
Or:
Operating conditions
When activated, lights up in the instrument clus-
ter.
✓ The parking aid is activated.
✓ The driving speed is higher than 5 km/h.
goes out when deactivated.
180 Driver assist systems › Pedestrian detection system
Function restriction
Pedestrian detection system
The function may be restricted or unavailable in the
Functionality
following cases:
Pedestrian recognition helps to prevent a collision
▶ About 30 seconds after starting ( lights up in
with crossing pedestrians by enabling automatic
the instrument cluster)
braking interventions.
▶ When driving around a sharp bend
Status display in the instrument cluster display
▶ During an ESC intervention
or
lights up - Danger of collision
Settings
Risk of collision in a speed range of 5-30 km/h
The system triggers automatic braking.
Automatic activation
Front Assist is automatically activated when the igni-
Risk of collision in a speed range of 30-60 km/h
tion is switched on.
The system warns of a collision hazard first. If the
driver does not respond, the vehicle is automatically
Activation/deactivation in the instrument cluster
braked.
› Press the button on the multifunction steering
wheel.
› Select Front Assist .
Operating conditions
Activation/deactivation in Infotainment
✓ Front Assist is deactivated.
In the menu
✓ The vehicle speed is 5-60 km/h.
Show system deactivation in the display of the in-
strument cluster
illuminates together with
Speed limiter
Functionality
or
illuminates together with
The speed limiter controls the maximum driving
speed according to the set speed limit.
Deactivate Front Assist when handling the vehi-
If the limit is exceeded when driving downhill, brake
the vehicle with the brake pedal.
cle on a truck, a car ferry etc.
Status display in the instrument cluster display
illuminates - the cruise control is activated.
Troubleshooting
ĔashiÄ£ - the set limit is exceeded
Front Assist is not available
When the regulation starts highlighted and the
illuminates together with
set limit is displayed.
Or:
Operating conditions
illuminates together with
✓ The driving speed is higher than 30 km/h.
› Clean the front radar sensor.
› Stop the engine and start again.
Operation
› If Front Assist is still unavailable, check the brake
lights on the vehicle or on the attached trailer.
Variant without cruise control
› If the brake lights are working and Front Assist is
still unavailable, seek the help of a specialist ga-
rage.
There was an unfounded warning or system inter-
vention
› Clean the front radar sensor.
› If the system is not working properly, disable Front
Assist and seek the help of a specialist garage.
Driver assist systems › Cruise control system 181
A
Activate limiter (control inactive)
Variant with ACC
Deactivate limiter
Interrupt control (sprung position)
B
Resume control1) / Increase limit
C
Start control with current speed / Reduce
limit
Variant with cruise control
Activate ACC (condition for the subsequent
activation of the limiter). To enable the speed
limiter, press the button and in the multi-
function steering wheel and in the instrument
A
Activate cruise control (condition for the
cluster choose the menu item Speed limit .
subsequent activation of the limiter).
To enable the speed limiter, press the button D
Resume control 1) / Increase limit in steps of
1 km/h (sprung position)
and in the instrument cluster choose the menu
item Speed limit .
Stop control (sprung position)
Deactivate limiter
Deactivate the limiter
Interrupt control (sprung position)
Increase limit in steps of 10 km/h
B
Resume control1) / Increase limit
Decrease limit in steps of 10 km/h
C
Start control with current speed / Reduce
Start control/Reduce limit in steps of 1 km/h
limit
Limit exceeded
D
Show menu of assist systems - Possibility of
› Fully depress the accelerator.
switching between cruise control and speed lim-
iter
Control will continue as soon as the vehicle has de-
Switching to cruise control interrupts the con-
celerated to below the set limit.
trol.
Adjusting the speed limit with the buttons B and
Troubleshooting
C
Speed limiter faulty
By pressing in steps of 1 km/h.
illuminates
By holding in steps of 10 km/h.
› Seek the help of a specialist garage.
Cruise control system
Functionality
The cruise control system maintains the set speed
without the accelerator pedal having to be operated.
This, however, is only possible to the extent permit-
ted by the engine output and braking power of the
vehicle.
1)
If no speed limit is set, the current speed is set as the speed limit.
182 Driver assist systems › Adaptive Cruise Control (ACC)
WARNING
Troubleshooting
Risk of the cruise control system starting uninten-
Cruise control system faulty
tionally!
illuminates
▶ Deactivate cruise control after use.
› Seek the help of a specialist garage.
Status display in the instrument cluster display
illuminated - the cruise control system is acti-
vated
Adaptive Cruise Control (ACC)
illuminated - cruise control is active
When cruise control starts, the set speed is
Functionality
displayed.
ACC control
ACC maintains the set speed. When your vehicle ap-
Operating conditions
proaches the vehicle in front, ACC will automatically
start to maintain the set distance to this vehicle.
✓ The driving speed is higher than 20 km/h.
Maintaining the set speed and the distance will here-
inafter be referred to as Control.
Operation
WARNING
ACC does not respond to crossing or oncoming ob-
Operating with the lever
jects.
ACC is intended primarily for use on motorways.
pACC (predictive cruise control)
pACC represents an extension of the ACC system.
pACC adjusts the speed according to recognized
speed limits and the route, e.g. curves, intersections
or roundabouts.
The system uses the following sources to evaluate
the situation:
▶ Navigation data
A
Activate cruise control (cruise control deacti-
▶ Traffi Sign Recognition
vated)
▶ Sensors, radars and cameras
Deactivate cruise control
WARNING
Interrupt control (sprung position)
pACC does not respond to railway crossings.
B
Resume cruise control1)/Increase speed
Speed range
C
Start control with current speed/Reduce
Depending on the equipment, ACC allows a speed
limit
setting in the range of 30-160 or 30-210 km/h.
D
Show menu of assist systems - Possibility of
If control is started at a speed of less than 30 km/h
switching between cruise control and speed lim-
on vehicles with an automatic transmission, the
iter
speed is automatically increased to 30 km/h or con-
trolled according to the speed of the vehicle ahead.
Accelerate temporarily
› Depress the accelerator pedal.
Distance level
Releasing the accelerator pedal will cause the speed
The distance to the vehicle ahead can be adjusted to
to drop again to the set speed.
five differeÄt levels.
WARNING
Interrupting cruise control
▶ Maintain a minimum distance in accordance with
▶ After pressing the brake pedal
the ouÄtrû-speifi legal regulations.
▶ After an ESC intervention
Automatic stop and start with automatic gearbox
A vehicle with an automatic transmission can be de-
celerated to a stop using the ACC and start moving
1)
If no speed is set, the current speed is adopted.
Driver assist systems › Adaptive Cruise Control (ACC) 183
again. Control is disconnected in case of longer hold-
Activate ACC (control inactive)
ing periods.
Start or resume control/Increase speed in
To resume the regulation:
steps of 1 km/h (sprung position)
› Depress the accelerator pedal.
Stop control (sprung position)
Or:
Deactivate ACC
› Set the lever in position
Increase speed in steps of 10 km/h
Or:
Reduce speed in steps of 10 km/h
› Applies to vehicles with hand recognition on the
Set distance level
steering wheel: Grab the steering wheel again.
Start control/Reduce speed in steps of 1
The control is interrupted when the brake pedal is
km/h
depressed.
Starting control with the current speed
Overtaking
› Tap on
If your vehicle changes to the fast lane and no vehi-
Or:
cle is detected in front, ACC accelerates up to the
set speed.
› If no speed is saved, move the lever to the sprung
position
Status display in the instrument cluster display
illuminates - ACC is activated
Set distance level
› Move the
switch to the sprung position
illuminates - Control is active
or
Line A appears in the
When the control starts, the set speed is displayed.
display, indicating the
illuminates - ACC does not decelerate suffi-
change in distance.
ieÄtlû
› Use the
switch
› Depress the brake pedal.
to set the desired dis-
tance level.
illuminates - ACC controls the driving speed ac-
cording to the permissible speed
illuminates - ACC controls the driving speed ac-
cording to the approaching roundabout
For temporary acceleration
illuminates - ACC controls the driving speed ac-
› Depress the accelerator pedal.
cording to the approaching junction
The vehicle accelerates and control is temporarily in-
illuminates - ACC controls the driving speed ac-
terrupted. Upon releasing the accelerator, control is
cording to the road
resumed.
Interrupting cruise control
Operation
▶ After pressing the brake pedal
▶ By operating the clutch pedal for a long time
Operating with the lever
▶ After an ESC intervention
▶ After deactivation of the ASR
Resuming control
› If a speed is stored, move the lever to the sprung
position
The vehicle is controlled at the set speed. The set
speed is shown in the instrument cluster display.
Function restriction
Do not use the ACC in the following cases:
▶ The vehicle is making a sharp turn.
▶ The vehicle is travelling on a sloping road or in ruts.
184 Driver assist systems › Adaptive Cruise Control (ACC)
▶
When the driving lane is too narrow.
Stationary vehicle
▶ The vehicle drives through a construction site.
WARNING
▶ Be particularly attentive and alert in the following
situations.
Regulation according to the vehicle in the adjacent
lane
If your vehicle is moving faster than the vehicle in
the next lane on the driver's side, at a speed of more
than 80 km/h, this may cause your vehicle to be con-
trolled according to that vehicle.
If a vehicle in front turns and there is a stationary ve-
When cornering
hicle in front of this vehicle, the ACC must not re-
spond to the stationary vehicle.
Vehicles with special load or special bodies
A load or superstructure that protrudes outside the
vehicle might not be detected by the ACC.
Settings
Activation / deactivation and setting
In the Infotainment system, in the menu
When cornering, a vehicle in the next lane may enter
◼
the detected area. Your vehicle will be controlled ac-
cording to this vehicle.
▶ Driving programme:
- Setting the vehicle acceleration
Narrow or staggered vehicle
when the ACC is switched on (this setting is
made for vehicles with driving mode selec-
tion » page 172)
▶ Last distance selected - Switch oÄ/off the last distance
selected
▶ Distance: - Setting the distance to vehicles in front
▶ Road layout preview - Switch the cruise control oÄ/off
according to the road profile (e.g. reduce speed
before a bend)
▶ Speed limit preview - Switch the speed control oÄ/off
according to the permissible speed
ACC detects a narrow or staggered vehicle only
when it is in the area covered by the radar.
Troubleshooting
Lane change by another vehicle
ACC not available
illuminates together with
or
illuminates together with
› Stop the engine and start again.
› If ACC is still unavailable, check the brake lights on
the vehicle or on the attached trailer.
› If the brake lights are working and ACC is still un-
A vehicle that changes to the lane a short distance
available, seek the help of a specialist garage.
away may not be recognized by the ACC in time.
Driver assist systems › Lane Assist 185
Lane Assist
✓ The lane markings are clearly visible.
Usage
Function restriction
Lane Assist helps to keep the vehicle within the lane.
It is based on the boundaries of a lane. These may in-
The system function may be restricted in the follow-
clude lane markings, road edges or objects such as
ing cases:
curbs or possibly traffi cones.
▶ The field of view of the sensor is limited by a dirty
The system is intended primarily for use on high-
screen or an obstacle or a preceding vehicle.
ways.
▶ If the weather conditions are unfavourable.
▶ The vehicle is making a sharp turn.
▶ The vehicle is travelling on a sloping road or in ruts.
Functionality
▶ When the driving lane is too narrow.
As the vehicle approaches a lane marking, the sys-
▶ The vehicle drives through a construction site.
tem executes a steering movement in the opposite
WARNING
direction from the lane marking. The steering inter-
vention can be overridden manually.
Danger of incorrect steering intervention!
Certain objects or markings on the road may be erro-
No system intervention occurs when changing lane
neously recognized as lane markings.
with the turn signal on.
▶ Always keep your hands on the steering wheel and
Status display in the instrument cluster display
be prepared to override the steering intervention.
lights up - System is activated and ready to
intervene
Settings
lights up - System is activated and ready to
intervene
Activation/deactivation in the instrument cluster
lights up - System intervenes
› Press the button on the multifunction steering
wheel.
lights up - System intervenes
› Select Lane Assist .
Activation/deactivation in Infotainment
Display
In the menu
Display example in black and white display.
Lane boundary highligh-
Troubleshooting
ted on the right: system
intervenes on the right
Message regarding system unavailability
when approaching the
› Clean the windscreen in the sensor area.
lane marking.
› Stop the engine and restart again after a short
In the coloured display,
time.
the lines are highlighted
› If the system is still not available, seek the help of a
in colour.
specialist garage.
Warning through steering wheel vibrations
Travel Assist
The steering wheel vibrations are triggered in the
Usage
following situations:
▶ The vehicle crosses the boundary line without the
Travel Assist helps to keep the vehicle within the
indicator light switched on.
lane while controlling the speed of the vehicle.
▶ The system is not able to keep the vehicle within
the lane.
Functionality
› Correct the steering movement in the event of vi-
brations.
Travel Assist uses the functions Lane Assist and
ACC.
Operating conditions
✓ The driving speed is higher than 60 km/h.
186 Driver assist systems › Lane change assist system Side Assist
WARNING
Settings
Risk of an accident!
Activation
▶ Always keep your hands on the steering wheel and
be ready to take over the steering.
› Press the
button on the multifunction steering
wheel.
▶ The notes in the functional description of Lane As-
sist and ACC are to be taken into account.
Regulation with the current speed and adaptive lane
assist are started.
Adaptive lane assist
This function keeps the driver within the selected
Deactivation
position within the lane.
› Depress the brake pedal.
Status display in the instrument cluster display
Or:
is lit up - the system is activated, cruise con-
› Set the ACC lever in position
» page 183.
trol and adaptive lane guidance are active
Additional settings are identical to ACC and Lane
is lit up - the system is activated, cruise con-
Assist.
trol is active
is lit up - the system is activated, adaptive
lane guidance is active
Troubleshooting
lights up - you have let go of the steering
Message regarding system unavailability
wheel, take over steering
› Follow the troubleshooting instructions in case of
lights up - you have released the steering
Lane Assist » page 185 and ACC » page 184.
wheel, take over steering immediately
› If the system is still not available, seek the help of a
specialist garage.
Operating conditions
Lane change assist system Side Assist
✓ The ACC is activated.
✓ The vehicle speed is max. 210 km/h.
Usage
✓ The lane markings are clearly visible.
The system uses optical signals in the exterior mirror
✓ In vehicles with manual gearbox, the vehicle
to alert the driver to vehicles that could be danger-
speed is higher than 30 km/h.
ous when changing lanes.
Function restriction
Functionality
Travel Assist is only for support and does not absolve
The system monitors the area both beside and be-
you from your responsibility for driving the vehicle.
hind the vehicle.
The function may be restricted or unavailable in the
The system warns of an approaching vehicle through
following cases:
the indicator light in the exterior mirror cover on
▶ The field of view of the sensor is limited by a dirty
the vehicle side, where the vehicle is recognized.
screen or an obstacle or a preceding vehicle.
Driving situations in which a system warning oc-
▶ If the weather conditions are unfavourable.
curs
▶ The vehicle is making a sharp turn.
▶ The vehicle is travelling on a sloping road or in ruts.
▶ When the driving lane is too narrow.
In addition to these restrictions, also note the ACC
restrictions » page 183.
WARNING
Danger of incorrect steering intervention!
Certain objects or markings on the road may be erro-
neously recognized as lane markings.
▶ Always keep your hands on the steering wheel and
be prepared to override the steering intervention.
Your vehicle is being overtaken by vehicle A . The
faster vehicle A approaches, the sooner the warning
is given by the indicator light.
Driver assist systems › Traffi sign recognition
187
Vehicle B is overtaken by your vehicle at a speed
› If the system is still not available, seek the help of a
that is faster by max. 10 km/h. If the speed is higher
specialist garage.
during the overtaking process, no warning will be
provided by the indicator light.
Traffic sign recognition
Indicator light
illuminates - There is another vehicle behind your
Usage
vehicle
The road sign recognition shows road signs in the
ĔashiÄg - There is another vehicle behind your ve-
display of the instrument cluster. This also indicates
hicle, and the turn signal on the same side is switch-
exceeding the speed limit.
ed on
WARNING
For vehicles with Lane Assist, the indicator light will
Road signs on the road always have priority over the
also Ĕash if your vehicle crosses the lane markings in
road signs shown on the display.
the direction of the approaching vehicle. The system
will trigger a steering wheel vibration in this case.
For this, Lane Assist must be activated and the lane
Functionality
marking between the vehicles must be detected.
Displayed road signs
▶ Speed limits
Operating conditions
▶ Overtaking prohibited
▶ Driving bans - one-way traffi
✓ The driving speed is higher than 15 km/h.
▶ Additional characters, e.g. speed limit in wet condi-
✓ No accessories are connected to the trailer sock-
tions
et.
Towing a trailer
If a trailer or other accessory is connected to the
Function restriction
trailer socket, trailer-relevant road signs are also dis-
played.
The system cannot detect lane width. For this rea-
son, it may, for example, draw attention to a vehicle
Driving on roads without speed limits
in a distant lane in the following cases:
If you are on a road with no speed limits, the road
signs will appear in the display.
▶ The vehicle is driving on a road with narrow lanes
or on the lane edge.
Example of road sign display
▶ The vehicle is taking a turn.
The system can draw attention to objects along the
road, such as high guard rails or noise barriers.
In the following cases, the system does not have to
issue a warning of a vehicle, or the warning may be
Example of additional characters
issued incorrectly:
Example of several simultaneously rec-
▶ If the weather conditions are unfavourable.
ognised road signs.
▶ A very fast approaching vehicle.
▶ The vehicle is driving through a sharp bend or a
roundabout.
At the same time, a red display regarding the
speed limit appears in the speedometer.
Settings
Speed units
The speed indications in the road signs shown refer
In the instrument cluster display
to the speed units that are common in the country.
In the menu Assist systems.
For example, the display may refer to 30 km/h or
In Infotainment
30 mph depending on the country.
In the menu
Restriction
Troubleshooting
The system function may be restricted in the follow-
Message regarding system unavailability
ing cases:
› Stop the engine and start again.
188 Driver assist systems › Crew Protect Assist proactive occupant protection
▶
The sensor is blinded by the sun or oncoming traf-
Risk of frontal impact
fi.
Applies to vehicles with the Front Assist system.
▶ The field of view of the sensor is limited by an ob-
The system triggers safety measures when it de-
stacle or a preceding vehicle.
tects the impending danger of a frontal impact.
▶ If the weather conditions are unfavourable.
Driver inactivity hazard
▶ The vehicle is moving at high speed.
Applies to vehicles with assist systems for emergen-
▶ The road signs are hidden, damaged, or are non-
cy situations.
standard.
The system triggers safety measures when it de-
▶ The road signs are attached to ĔashiÄ£ neon signs.
tects the impending danger if the driver is inactive.
▶ The navigation map documents are not up-to-date
or not available.
Function restriction
Settings
The function may be restricted or unavailable in the
following cases:
Activation / deactivation and setting
▶ When deactivated in the infotainment in the menu
In the Infotainment system, in the menu
▶ When deactivating the ASR or activating the ESC
◼ Traffic Sign Recognition
Sport
▶ Show in instrument cluster - Activation/deactivation of
▶ When reversing
the additional road signs in the display of the in-
▶ If there is a malfunction in the ESC, reversible seat
strument cluster
belt or airbag system
▶ Speed warning: - oÄfi£ures a warning when the
▶ If there is a malfunction or limitation of the Front
speed limit is exceeded
Assist system
▶Warning at over - Increases the speed limit for the
▶ If there is a malfunction or restriction of the Emer-
warning when exceeding the permitted speed
gency Assist assist systems
◼ Trailer detection
▶ Show road signs relevant to trailers Activation/deactivation
of the display of road signs relevant to trailers
Settings
▶ Use for route calculation - Activation/deactivation taking
Automatic activation
trailers in account for route calculation in naviga-
The system is automatically activated when the igni-
tion
tion is switched on.
▶ Tap on maximum speed for trailers - Setting the speed limits
for trailer operation
Troubleshooting
Crew Protect Assist proactive occupant
Crew Protect Assist faulty
illuminates together with
protection
Message concerning unavailability or function-
Usage
al restriction
› Seek the help of a specialist garage.
The system of proactive occupant protection trig-
gers measures to protect vehicle occupants in dan-
gerous situations.
Driver Alert fatigue detection assistant
Functionality
Functionality
If the system evaluates the situation as critical, it
Driver Alert evaluates the steering behaviour. If it de-
triggers the following safety measures:
tects fatigue in the driver, a break is recommended.
In the display of the instrument cluster, the following
▶ Open windows are closed except for a small gap.
symbol lights up from the isolation box.
▶ The sliding/tilting roof is closed.
WARNING
▶ The front seat belts are tightened on the body.
There will be no system warning during the so-called
The system response depends on the selected
micro-sleep.
driving mode.
Driver assist systems › Emergency situation assist systemEmergency Assist 189
Resetting the break recommendation
✓ ACC is enabled.
The break recommendation is reset in the following
cases:
Hill descent assistant
▶ The vehicle stops and the ignition is switched off
▶ The vehicle stops, the seat belt is removed and the
Functionality
driver's door is opened
▶ The vehicle stops for more than 15 minutes
The Hill Hold Control helps to maintain a constant
speed when driving downhill through automatic
In some situations, the system may erroneously
brake interventions.
issue a break recommendation.
The system also works when driving in neutral or
when reverse gear is engaged.
Operating conditions
WARNING
Risk of an accident!
✓ Driving speed between 60-200 km/h.
The system cannot properly fulfil its function on slu-
shy soil for physical reasons, e.g. ice or mud.
Settings
Status display in the instrument cluster display
lit up in grey - the system is activated
Activation/deactivation
lit up white / green - the system intervenes
In the Infotainment system, in the menu
Change speed
The driving speed can be changed by pressing the
brake or accelerator pedal. After releasing the pedal,
Emergency situation assist
the assist system maintains the current speed.
systemEmergency Assist
Usage
Operating conditions
The assist systems for emergencies detect inactivity
✓ The engine is running.
of the driver, which, for example, can be caused by a
✓ Offroad is activated.
sudden loss of consciousness. The system then per-
✓ The slope is at least 10 %.
forms measures as safely as possible to decelerate
✓ Neither the accelerator nor the brake pedal is
the vehicle to a stop.
pressed.
The assist systems are only available for vehicles
✓ The vehicle speed is max. 30 km/h.
with an automatic gearbox.
Settings
Functionality
Automatic activation
When the assist system detects inactivity on the
The system will be automatically activated when you
part of the driver
turn on Offroad mode.
▶ An acoustic warning signal sounds and a message
appears in the instrument cluster display.
Activation/deactivation in Infotainment
▶ If, after repeated warnings, the driver does not
The system is activated or deactivated in the follow-
take over the steering, the hazard warning lights
ing menu.
are switched on and the vehicle automatically
brakes.
Or:
▶ After the vehicle has come to a standstill, the park-
ing brake is switched on.
Interruption of automatic braking
▶ By pressing the brake or accelerator pedal
▶ By actively steering
Operating conditions
✓ Lane Assist is activated and the boundary lines of
the traffi lane are recognised.
190 Park Assist systems › Park Pilot parking aid
Park Assist systems
› Press the button.
Automatic switch-on during forward travel
Park Pilot parking aid
When approaching an obstacle at a speed of less
than 10 km/h.
Functionality
Automatic switch-on does not activate automatic
If an obstacle is detected, the Infotainment will dis-
braking.
play a visible message and an audible signal will
sound.
Switching off
› Disengage reverse gear.
The interval between the signals becomes shorter as
the clearance is reduced. At a distance of less than
Or:
30 cm from the obstacle, a continuous tone sounds.
› Press the button.
If the driver does not respond to the warning, the
Automatic switch off
system triggers automatic emergency braking at
The driving speed is higher than 15 km/h.
speeds below 10 km/h in order to reduce the impact.
Automatic braking can be activated and deactivated
in the infotainment.
Function restriction
In the following cases, the system does not have to
issue a warning of an obstacle, or the warning may
Display
be issued incorrectly:
The recorded areas vary according to the equipment.
▶ If the weather conditions are unfavourable.
▶ The detected obstacles are moving.
▶ Sensor signals are not reĔeted by the surface of
the obstacles.
▶ It is a small obstacle, e.g. a stone or a pillar.
Settings
The system settings are made in the infotainment
system in the following menu:
A
Route controlled at the current steering angle
Acoustic signals oÄ/off
Or:
One-time deactivation/activation of automatic
braking
Change to the rear view camera display
Troubleshooting
System fault
After switching on, an audible signal sounds for 3
Obstacle at a distance of less than 30 cm
seconds and there is no obstacle near the vehicle
Obstacle at a distance of more than 30 cm
› Seek the help of a specialist garage.
Obstacle outside the route
After switching on, the symbol Ĕashes in the
button
›
Seek the help of a specialist garage.
Operating conditions
After switching on, not all scanned areas are dis-
✓ The driving speed is lower than 15 km/h.
played on the Infotainment screen
✓ No accessories are connected to the trailer sock-
› Move the vehicle a few meters forwards or back-
et.
wards.
› If the scanned areas are still not displayed, seek the
help of a specialist garage.
Turn on/turn off
Switching on
› Engage reverse gear.
Or:
Park Assist systems › Rear view camera 191
Rear view camera
Switch audible parking signals oÄ/off
Functionality
Operating conditions
When reversing, the area behind the vehicle is dis-
played in the Infotainment screen complete with ori-
✓ Ignition on
entation lines.
✓ Driving speed less than 15 km/h
The camera is equipped with a cleaning system.
Cleaning takes place automatically when the rear
window is washed.
Operation
Switch on the system
› Engage reverse gear.
Orientation lines and functional surfaces
Or:
Orientation lines
›
Press the button.
When switching on, an alarm sounds and the symbol
lights up in the button
from the isolation box.
Mode for transverse parking
› Stop the vehicle in
front of a suitable
parking space.
› Reverse so that the
yellow lines lead into
the parking space.
A
Distance about 40 cm
› At the latest, stop
B
Distance about 100 cm
when the red line
C
Distance about 200 cm
touches the rear boun-
D
The lines indicate the track, which is controlled
dary (e.g. curb).
at the current steering angle. The distance be-
Mode for parallel parking
tween the side lines corresponds approximately
› In the screen, select the mode for parallel parking.
to the vehicle width including mirrors.
› Turn on the indicator light for the side on which
Function surfaces
you want to park.
› Stop the vehicle stop
so that there are no
obstructions in the gap
between the auxiliary
boxes A and the rear
box does not extend
over the side of the
parking space (e.g.
kerb).
› Turn the steering
A
Mode for transverse parking
wheel in the recom-
mended direction B until the red colour of the tra-
B
Mode for parallel parking
pezoidal border C turns green.
C
Mode for driving up to a trailer/distance moni-
toring
D
Mode for monitoring the area behind the vehicle
(wide view)
E
Brightness, contrast and colour settings of the
screen
F
Parking Aid View
Switch the view on / off
Full Screen
192 Park Assist systems › Area View environment overview
› Hold the steering
Area View environment overview
wheel in the adjusted
position and reverse.
Usage
› Stop the vehicle if the
The area view assists the driver in parking and ma-
green line overlaps
noeuvring by displaying the vehicle area.
with the lateral boun-
dary of the parking
space (e.g. the curb) or
Overview
if
is displayed.
› Countersteer until the
General overview
yellow lane line crosses
the red line for the required lane orientation.
› Hold the steering wheel in the adjusted position
and reverse.
› Stop the vehicle at a safe distance from the obsta-
cle or when is displayed.
Mode for driving up to a trailer/distance monitor-
ing
The screen shows the area behind the vehicle in plan
view.
A
3D views:
On vehicles with a factory fitted tow-bar, this mode
Top view
assists the driver when the vehicle is approaching a
View obliquely from above
trailer draw bar. A line for approaching the trailer
View from the side
draw bar and lines for estimating distance are dis-
played on the screen.
Overall view
By moving your fiģer across the screen, you can
For vehicles without a factory fitted tow bar, a line
for monitoring the distance to obstacles is displayed
change the viewing angle.
on the screen at a distance of 40 cm behind the vehi-
Camera rear view
cle.
Mode for monitoring behind the vehicle
The area behind the vehicle is displayed on the
screen.
Switch off the system
› Press the button.
Or:
› For vehicles with an automatic gearbox, put the se-
lector lever in the position.
A
Mode for transverse parking
Automatic shut-off
The automatic system shut-off occurs when driving
B
Mode for parallel parking
forward at a speed over 15 km/h.
C
Mode for driving up to a trailer/distance moni-
toring
D
Mode for monitoring the area behind the vehicle
Restriction
(wide view)
The camera image is distorted in contrast to the nak-
ed eye. The display may only be used to estimate the
distance.
Some items may not be displayed properly on the
screen. These include narrow columns, wire mesh
fences, grids or road bumps.
Park Assist systems › Rear Traffi Alert
193
Front camera view
ted area is highlighted on the screen by a yellow bor-
der.
Switching off
›
Press the button.
Or:
› For vehicles with an automatic gearbox, put the se-
lector lever in the position.
Automatic shut-off
The automatic system shut-off occurs when driving
forward at a speed over 15 km/h.
A
Mode for transverse parking
The orientation lines are used for estimating dis-
tance as well as for displaying the route, which is
Restriction
controlled at the current steering angle.
The camera image is distorted in contrast to the nak-
B
Mode for monitoring the area in front of the ve-
ed eye. The display may only be used to estimate the
hicle (wide view)
distance.
The area right in front of the vehicle is marked
by the blue lines.
Some items, such as thin posts, chain link fences,
grilles or uneven road surfaces may not be properly
C
Distance monitoring mode
displayed.
Side camera view
Objects directly beside the corners of the vehicle
may be outside the field of view of the cameras and
may therefore not be displayed on the screen.
Troubleshooting
After switching on, the symbol Ĕashes in the
button
›
Seek the help of a specialist garage.
A
Left side
Rear Traffic Alert
B
Right side
Functionality
C
Left and right side
When reversing, the
The yellow line is shown at a distance of about
Rear Traffi Alert warns
40 cm from the vehicle.
of approaching vehicles.
If the driver does not re-
spond to the warning,
Operating conditions
the vehicle is braked au-
✓ The ignition is switched on.
tomatically at a speed
✓ The driving speed is lower than 15 km/h.
below 10 km/h.
Operation
Vehicle with Parking Aid
If an approaching vehicle is detected in the area be-
Switching on
hind your vehicle, a graphical warning is displayed in
› Engage reverse gear.
the Infotainment. At the same time, a continuous
Or:
tone sounds.
› Press the button.
Selecting the camera image
The respective camera image is selected by touching
the screen in the Infotainment in the area next to, in
front of or behind the vehicle silhouette. The selec-
194 Park Assist systems › Park steering assistant
Park steering assistant
Usage
Park Assist helps drivers park in parallel and perpen-
dicular parking places and to manoeuvre out of par-
allel parking spaces.
Functionality
Vehicle in collision area - danger of collision!
The system looks for a parking space and only takes
Approaching vehicle
over the steering during the parking procedure or
when leaving a parking place. The driver operates the
Vehicle without Parking Aid
pedals and the shift lever/gear selector.
If an approaching vehicle is detected in the area be-
The system displays information and notes on the in-
hind your vehicle, the a warning is displayed in the in-
strument cluster display.
strument cluster display, indicating to the driver to
monitor the traffi behind. At the same time, an
If the system detects a risk of collision, automatic
acoustic signal sounds.
emergency braking takes place to prevent a collision.
Operating conditions
Operating conditions
✓ No accessories are connected to the trailer sock-
✓ The driving speed is lower than 7 km/h.
et.
✓ The ASR is activated and there is no intervention.
✓ There is no driver intervention in the automatic
steering operation.
Function restriction
✓ No accessories are connected to the trailer sock-
Manoeuvre Assist’s functionality may be limited in
et.
unfavourable weather conditions.
Operation
Settings
Turn on/turn off
Activation/deactivation in the instrument cluster
› Press the
button.
display
When the system is switched on, the symbol lights
In the menu Assist systems.
up in the button
Activation/deactivation in Infotainment
Select the lane side for the parking procedure
In the following menu:
The system automatically searches for a suitable
parking space on the passenger side.
Or:
› Press the driver's side indicator to fiÄd a parking
space on this side of the road.
Operation while searching for a parking space
›
Drive past a number of parked vehicles at a dis-
Troubleshooting
tance of 0.5-1.5 m.
› To search for a parking space across the road, drive
Message regarding system unavailability
slower than 20 km/h.
› Stop the engine and start again.
› To search for a parking space along the road, drive
› If the system is still not available, seek the help of a
slower than 40 km/h.
specialist garage.
If the symbol
(km/h) appears in the display, reduce
the driving speed. If the system fiÄds a parking
space, the display will show the recommended park-
ing mode.
Changing the parking mode
If a suitable parking space is found, the following
Park modes can be shown in the display.
Park Assist systems › Trailer assist trailer manoeuvring aid
195
Exiting a parking space
›
Press the
button.
When the system is switched on, the symbol lights
up in the button
› Follow the instructions on the screen.
Automatic speed reduction
If a speed of 7 km/h is exceeded during the parking
process, the system will reduce the speed.
Upon the speed being exceeded by 7 km/h a second
Park backwards longitudinally
time, the parking process is terminated.
Park backwards crosswise
Park forwards across
Function restriction
The parking mode can be changed by pressing the
If the parking space is too small, it is not possible to
button
use the Park Assist to initiate a parking manoeuvre.
A message is shown on the instrument cluster dis-
Press the button again
and the system is switch-
play.
ed off.
Do not use the Park Assist in the following cases:
› To return to the original recommended parking
mode, press the button again.
▶ The vehicle is moving on unpaved or slippery surfa-
ces.
Before the parking process
▶ If snow chains or a spare wheel are mounted on
› If a suitable parking space is found, stop and drive
the vehicle.
backwards or forwards as indicated by the arrow in
the display.
▶ If the system chooses an inappropriate parking
space for parking.
› When a steering intervention message is displayed,
release the steering wheel. The steering operation
is taken over by the system.
Troubleshooting
Parking operation
Message regarding system unavailability
CAUTION
› Stop the engine and start again.
Risk of injury!
› If the system is still not available, seek the help of a
▶ Do not reach between the steering wheel spokes
specialist garage.
during the parking manoeuvre.
▶ Only operate the pedals and the shift / selector
Incorrect resulting position of the vehicle in the
lever.
parking space
The correct parking procedure depends on the size
› Observe the area around the vehicle and drive
of the wheels. If other wheels approved by ŠKODA
backwards or forwards in accordance with the ar-
AUTO are fitted, have the system readjusted by a
row in the display.
specialist garage.
› As soon as the symbol appears in the display
and an audible signal sounds, stop the vehicle. The
steering wheel is taken over accordingly. The sym-
Trailer assist trailer manoeuvring aid
bol
goes out.
› Travel backwards or forwards in accordance with
Usage
the arrow in the display.
The trailer manoeuvring aid helps the driver when re-
As soon as the parking process is completed, the
versing with a trailer.
corresponding message is displayed and an audible
signal sounds.
What you should be mindful of
The parking procedure can be ended at any time by
pressing the button
Use the system extremely carefully in the following
When partially parked in a suitable transverse
cases:
parking space forward, press button . The parking
▶
The vehicle is moving on unpaved or slippery surfa-
process is completed by the system.
ces.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст