Skoda Superb (2019 year). Manual — part 4
Open / close door
Fig. 54 Door handle/door opening lever
Read and observe and on page 57 first.
›
To open from outside, unlock the vehicle and pull the door handle
A
in the
direction of arrow
.
›
To open from inside, pull on the door opening lever
B
and push the door
away from you.
›
To close from inside, grip the handle
C
and close the door.
WARNING
■
The door must be closed properly, otherwise it could open whilst driving -
risk of death!
■
Only open and close the door when no one is located in the opening/clos-
ing range – risk of injury!
■
Never drive with the doors open - it can be fatal!
■
An opened door can close automatically if there is a strong wind or the
vehicle is on an incline – risk of injury!
Note
On vehicles with door warning lights, these illuminate after the door is opened.
Child safety lock
Fig. 55 Rear door: Child safety system switch on / off
Fig. 56
Child safety lock with electric
operation
Read and observe and on page 57 first.
The child safety lock can be operated manually or electrically depending on
equipment.
The child safety lock prevents the rear door from being opened from the in-
side. The door can only be opened from the outside.
Manually controlled parental settings
›
To switch on, turn the parental control with the vehicle key in position
.
›
To switch off, turn the parental control with the vehicle key in position .
Child safety lock with electric operation
›
To switch on/off the child safety lock in the left rear door, press the button
A
in the driver's door
.
›
To switch on/off the child safety lock in the right rear door, press button
B
in the driver's door.
61
Unlocking and opening
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Locking is displayed in the button by the illumination of the symbol .
When with electric operation in addition to the electric window is blocked in
the respective door.
Malfunctions
Read and observe and on page 57 first.
Synchronising the remote control
If the buttons on the remote control key have been operated several times be-
yond the effective range of the system or the battery in the remote control
key has been replaced and the vehicle cannot be unlocked using the remote
control, the key must be synchronised.
›
Press any button on the remote control key.
›
Unlock the door with the key in the lock cylinder within 1 minute of pressing
the button.
Fault with the central locking
If the warning light in the driver's door initially flashes quickly for around 2 sec-
onds, and then illuminates for 30 seconds without interruption before flashing
again slowly, you will need to seek the assistance of a specialist garage.
A fault in the central locking system means the vehicle doors and the boot lid
cannot be emergency locked or emergency unlocked
.
Failure of the system KESSY
If there is a fault in the KESSY system, the appropriate error message is dis-
played in the instrument cluster.
Low voltage of the key battery
If the voltage of the key battery is too low, a message appears in the display of
the instrument cluster referring to the need to replace the battery. Replace the
battery
Anti-theft alarm system
Introduction
The alarm system triggers audible and visual signals if an attempt is made to
break into the vehicle (hereafter referred to as alarm).
The alarm system is activated automatically approximately 30 seconds after
the vehicle is locked. This is automatically disabled after release.
CAUTION
Before leaving the vehicle, it must be checked that all of the windows, doors
and the sliding/tilting roof are locked in order to ensure the full functionality of
the anti-theft alarm system.
Note
The alarm system has its own power source, service life of which is 5 years. In
order to ensure functionality of the alarm system, we recommend that you get
the alarm checked after this time by a specialist garage.
Alarm trigger
Read and observe on page 62 first.
The alarm is triggered when one of the following unauthorised actions is acti-
vated on the vehicle with an activated warning system.
▶
Opening the bonnet.
▶
Opening the boot lid.
▶
Opening the doors.
▶
Manipulation of the ignition lock.
▶
Towing the vehicle.
▶
Movement in the vehicle.
▶
Sudden and significant voltage drop of the electrical system.
▶
Uncoupling the trailer.
An alarm is triggered also when the driver's door is unlocked and opened by
the lock cylinder.
The alarm is switched off by pressing the button on the key or switching on
the ignition.
Interior monitor and towing protection
Read and observe on page 62 first.
The interior monitor detects movements inside the locked vehicle and then
triggers the alarm.
The anti-towing detects tilts in the locked vehicle and then triggers the alarm.
62
Using the system
-------------------------------------------------------------------------------------------------------------------------------------------------------------
These functions should be deactivated if there is a possibility that the alarm
will be triggered by movements (e.g. by people or animals) within the vehicle
interior or if the vehicle has to be transported (e.g. by train or ship) or towed.
Disable both functions once
▶
In the infotainment system, in menu
/ → → Open and close,
▶
By locking twice within 2 seconds.
Safelock is switched off during deactivation
.
CAUTION
The opened glasses storage compartment reduces the effectiveness of the in-
terior monitor. To ensure the full functionality of the interior monitor, the
glasses storage compartment must always be closed before locking the vehi-
cle.
Manually operated tailgate
Introduction
WARNING
■
Never drive with the boot lid open or ajar, as otherwise exhaust gases
may get into the interior of the vehicle – risk of poisoning!
■
Ensure that the lock is properly engaged after closing the lid. Otherwise,
the lid might open suddenly while the vehicle is moving, even if the lid was
locked – risk of accident!
■
Make sure that when closing the boot lid, no body parts are crushed -
there is danger of injury!
■
Do not press on the rear window when closing the boot lid, it could crack
– risk of injury!
Open/close boot lid
Fig. 57 Opening / closing tailgate
Read and observe on page 63 first.
›
To open, press the
A
button in the direction of arrow
1
.
›
Raise the lid in the direction of the arrow
2
.
›
To close, grab the mount
B
and pull in the direction of arrow
3
.
Note
Button
A
is deactivated when starting or at a speed of more than 5
km/h. The button is activated again after the vehicle has stopped and a door is
opened.
Setting the delayed locking of the boot lid
Read and observe on page 63 first.
If the boot lid is unlocked with the button on the key, the lid is automatical-
ly locked again after closing.
The period after which the boot lid is locked automatically can be extended by
a specialist garage.
CAUTION
There is a risk of unwanted entry into the vehicle before the boot lid is locked
automatically.
63
Unlocking and opening
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Electric boot lid
Introduction
The boot lid (hereinafter as lid) can be operated electrically and manual in the
event of an emergency
.
WARNING
■
Ensure that the lock is properly engaged after closing the lid. Otherwise,
the lid might open while the vehicle is moving - risk of accident.
■
Never drive with the lid open or unlatched, as otherwise exhaust gases
may get into the interior of the vehicle – risk of poisoning!
■
Only open and close the lid when no one is located in the opening/closing
range – risk of injury!
■
Make sure that no limbs are caught or crushed when closing the lid - risk
of injury!
CAUTION
■
Do not attempt to close the lid manually during electrical motion - there is a
risk of damaging the electric lid operation.
■
Lock the vehicle before driving through a car wash (or with the central lock-
ing button). In some car washes the boot lid might open automatically due to
the pressure action of the washing brushes - there is a risk of damage to the
vehicle interior, as well as to the objects being transported.
CAUTION
■
Before opening / closing the flap, check that there are no objects in the
opening / closing area that could damage the flap, and if there are any objects
in the immediate vicinity of the vehicle that could damage the vehicle interior
and the objects being transported.
■
In certain circumstances, if the lid is loaded (e.g. by a thick layer of snow), the
opening process of the lid can be interrupted. Remove the snow from the lid to
re-enable the electrical operation.
■
If the lid closes automatically (e.g. under load of snow), you will hear an inter-
mittent beep.
■
The flap is always to be close before disconnecting the battery.
Description of operation
Fig. 58 Lid operation
Read and observe and on page 64 first.
Ways to open the lid
▶
By pressing the handle
A
▶
By holding the button
C
.
▶
By holding the button
D
on the key.
If the lid hits an obstacle when closing, it stops and an audible signal sounds.
Ways to close the lid
▶
By pressing the button
B
▶
By holding the button
D
on the key (applies to vehicles with the KESSY key-
less unlocking system). The key must be located at a maximum distance of 2
m from the lid.
▶
By pressing the handle
A
.
▶
By briefly pressing the lid downwards.
If the flap meets an obstacle when it is closed, it stops, an acoustic signal
sounds and the flap moves back a few centimetres.
64
Using the system
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Ways to stop the lid movement
▶
By pressing the button
B
» Fig. 58
.
▶
By pressing the button
C
.
▶
By holding the button
D
on the key.
▶
By pressing the handle
A
.
Audible signals
When opening the door using the button
C
and opening / closing of the flap
using the button
D
audible signals are emitted.
Note
■
Button
A
is deactivated when starting or at a speed of more than 5
km/h. The button is activated again after the vehicle has stopped and a door is
opened.
■
If you rapidly enter the vehicle during the opening or closing process of the
lid, the whole vehicle may jerk and, as a result, the movement of the lid can be
interrupted.
Set the top position of the lid
Read and observe and on page 64 first.
The top position of the lid can be adjusted (e.g. in a limited space to open the
lid due to the garage height or for a more comfortable operation, depending
on the height of the person).
Adjusting the top position of the lid
›
Stop the lid in the desired position.
›
Press and hold button
B
on page 64 until you hear an acoustic sig-
nal.
Adjusting the top starting position of the lid
›
Carefully raise the flap manually to the limit.
›
Press and hold button
B
on page 64 until you hear an acoustic sig-
nal.
Note
The top position which is reached when the lid opens automatically, is always
lower than the maximum top position which can be reached when the lid is
opened manually.
Malfunctions
Read and observe and on page 64 first.
Examples of operational malfunctions
Description of the malfunc-
tion
Remedy
The lid cannot be opened
Unlocking the lid
The lid does not react to an
opening signal
Removing a possible obstacle (e.g. snow), re-
opening the lid
Press handle
A
on page 64 and pull
the lid upwards
The lid remains in the top
position
Manual closing of the lid
The lid is open and the bat-
tery was disconnected
Close manually
Close the door slowly, push down the lid, push in the lock on the centre of the
edge, above the ŠKODA logo.
Operating contactless boot lid
Fig. 59
Opening the boot lid
Read and observe and on page 64 first.
Depending on equipment the boot lid can be operated without contact.
The ignition must be switched off and you have to have the vehicle key on
your person.
65
Unlocking and opening
-------------------------------------------------------------------------------------------------------------------------------------------------------------
›
To open/close, move one foot in the sensor area below the rear bumper
quickly in the direction of the arrow
The flap opens / closes automatically. When opening the fully closed flap, the
brake light in the rear window lights up. An acoustic signal is sounded when
closing the lid.
If the lid does not move, then repeat the operating process after a few sec-
onds.
The lid movement can be stopped by a rapid swinging of the foot. Swinging
the foot again will continue the lid movement.
The function can be deactivated/activated in Infotainment in the menu
/
→ → Opening and closing → “Easy Open”.
We recommend that the function is deactivated in the following cases:
▶
Installation of a roof rack.
▶
Connecting a trailer (accessory) to the towbar.
▶
Manual vehicle wash.
▶
Maintenance and repair work in the back of the vehicle.
When connecting a device to the trailer socket the deactivation of the func-
tion takes place.
Note
With heavy rain or a dirty rear bumper, under certain circumstances that there
may be limitations, or the automatic deactivation of the contactless opening
function of the boot lid may occur.
Window operation
Introduction
WARNING
■
Always close the window carefully and controlled. Doing so may may
cause yourself or fellow passengers considerable crushing injuries.
■
The system is fitted with a force limiter
. If there is an obstacle
(e.g. In the event of a body part becoming trapped) the closing process is
stopped and the window goes down by several centimetres. However, the
windows should be closed carefully – risk of injury.
CAUTION
■
Keep the windows clean to ensure the correct functionality of the electric
power windows.
■
Always close the windows before disconnecting the battery.
Note
If the windows are opened, dust and other dirt can get into the vehicle and the
wind noise is more at certain speeds.
Open / close Window
Fig. 60 Buttons for window lifter
Fig. 61
Button of the window lifter on
the passenger side
Read and observe and on page 66 first.
All windows can be operated from the driver's seat. The window in the front
passenger door and the windows in the rear doors are operated via the button
in each door.
66
Using the system
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Power window buttons
Front door left
Front door right
Rear door, left
Rear door, right
Deactivate/activate the buttons in the rear doors (the deactivation may be
advantageous if, for example, children are transported on the rear seats)
Deactivation / activation of the key in the rear door left (part of the child
safety lock with electric operation)
Deactivation / activation of the key in the back door right (part of the child
safety lock with electric operation)
Open/close window
›
To open, lightly press the appropriate button down and hold it until the win-
dow has moved into the desired position.
›
or: Press the button to the stop; the window automatically opens fully. Re-
newed pressing of the button causes the window to stop.
›
To close, pull gently on the top edge of the corresponding button and hold
until the window has moved into the desired position.
›
or: Pull the button briefly to the stop, the window automatically closes fully.
Renewed pulling of the button causes the window to stop immediately.
Disable / enable buttons in the rear doors
›
To deactivate/activate the buttons in the rear doors, press the
E
button. If
the buttons in the rear doors are deactivated, the warning light
illuminates
in the
E
button.
›
or: On vehicles with child safety lock with electric operation, press the re-
spective key
F
or
G
. If the buttons in the rear doors are deactivated, the
warning light
illuminates in the respective button
F
or
G
.
Note
■
After switching off the ignition, the windows can still open and close for
about 10 minutes.
■
After the driver or front passenger door is opened, the operation of the win-
dow is only possible with the button
A
, in which case this is pressed
or pulled for approx. 2 seconds.
A
B
C
D
E
F
G
Force limiter
Read and observe and on page 66 first.
The electrical power windows are fitted with a force limiter.
If there is an obstacle, the closing process is stopped and the window goes
down by several centimetres.
If the obstacle prevents the window from being closed during the next 10 sec-
onds, the closing process is interrupted once again and the window goes down
by several centimetres.
If you attempt to close the window again within 10 seconds of the window be-
ing moved down for the second time, even though the obstacle was not yet
been removed, the closing process is only stopped. During this time it is not
possible to automatically close the window. The force limiter is still switched
on.
The force limiter is only not operational if you attempt to close the window
again within the next 10 seconds – the window will now close with full force!
If you wait longer than 10 seconds, the force limiter is switched on again.
Window convenience operation
Read and observe and on page 66 first.
The convenience operation for the window offers the option to open/close all
the windows at once (or only the window in the driver's door). The conven-
ience operation function can be adjusted individually in Infotainment in the
menu
/ → → Opening and closing.
Opening
›
Press and hold the button on the key.
›
or: Switch off the ignition, open the driver's door and hold the key
A
until it
stops in the open position
Closing
›
Press and hold the button on the key.
›
or: Switch off the ignition, open the driver's door and hold the key
A
until it
stops in the closed position
›
In the KESSY system, hold your finger on the sensor on the outside of the
door handle of the front door
67
Unlocking and opening
-------------------------------------------------------------------------------------------------------------------------------------------------------------
The convenience operation will only function correctly if all the windows auto-
matically open/close properly.
Convenience opening or closing the window using the key in the driver's door
locking cylinder is only possible within 45 seconds of locking the vehicle.
The movement of the window is stopped immediately when the respective
button is released.
Note
The settings for the window convenience operation are stored (depending on
the Infotainment type) in the active user account personalisation
.
Malfunctions
Read and observe and on page 66 first.
Repeatedly opening and closing the window can cause the window mechanism
to overheat and become temporarily blocked. You will be able to operate the
window again as soon as the operating mechanisms has cooled down.
After disconnecting the vehicle battery, automatic opening / closing the win-
dow can be deactivated. In this case the system must be activated as follows.
Activate window operation
›
Switch-on the ignition.
›
Pull the top edge of the button and close the window.
›
Release the button.
›
Pull up the respective button and hold for 1 second.
Panoramic tilting / sliding sunroof
Introduction
The panorama sliding/tilting roof (hereinafter referred to as sliding/tilting roof)
can only be operated when the ignition is turned on and when the outdoor
temperature is no lower than -20 °C.
The sliding/tilting roof can still be operated for approx. 10 minutes after
switching the ignition off. After opening the driver or front passenger door, it
is no longer possible to operate the sliding/tilting roof.
WARNING
When operating the sliding/tilting roof and the sunshade, proceed with
caution to avoid causing crushing injuries – risk of injury!
CAUTION
■
During the winter, remove any ice and snow in the vicinity of the sliding/tilt-
ing roof before opening it to prevent any damage to the opening mechanism.
■
Always close the sliding/tilting roof before disconnecting the battery.
Operation
Fig. 62 Operation of the sliding/tilting roof
Read and observe and on page 68 first.
Operation of the sliding/tilting roof
Gradual opening
Complete opening
Gradually reset
Fully reset
Gradual opening
Fully opening
After the first press, the sliding/tilting roof stops in the position where the
intensity of the wind noise is low (at speeds of approx. less than 80 km/h).
Press again and the sliding/tilting roof goes to the stop.
Gradual closing
Complete closing
1
2
3
4
5
6
7
8
68
Using the system
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Force limiter
Read and observe and on page 68 first.
The sliding/tilting roof is fitted with a force limiter.
If there is an obstacle, the closing process is stopped and the glass pane re-
tracts by several centimetres.
WARNING
If the sliding/tilting roof is closed by holding down the switch
7
/
8
,
on page 68and the closing process is hindered by an obstacle, then
when attempting to close for a third time, the force limiter is rendered in-
operable (if the period of 5 s is not reached between the individual at-
tempts to close). The sliding/tilting roof closes with full force - it may cause
injury.
Convenience operation of the sliding / tilting roof
Read and observe and on page 68 first.
The convenience operation makes it possible to open or close the sliding/tilt-
ing roof using the key or the KESSY system via the sensor in the door handle
of the front door.
›
To open out, press and hold the button on the key.
›
To close, press and hold the button (with KESSY, hold your finger on the
sensor on the outside of the door handle of the front door).
By interrupting the locking process, the closing operation is interrupted.
Activate operation of the sliding/tilting roof
Fig. 63
Operation of the sliding/tilting
roof
Read and observe and on page 68 first.
If the operation of the sliding/tilting roof is deactivated (e.g. after disconnect-
ing and connecting the battery), then operation will have to be activated.
›
Switch on the ignition, pull the switch on the recess all the way down in the
direction of arrow
1
The sliding/tilting roof opens/closes again after around 10 seconds.
›
Release the lever.
Manually operated sunshade
Fig. 64
Operation of the sunshade
Read and observe and on page 68 first.
›
To open, pull the handle in the direction of arrow
A
» Fig. 64
›
To close, pull the handle in direction of arrow
B
.
69
Unlocking and opening
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Electrically operated sunshade
Fig. 65
Buttons for operating the sun-
shade
Read and observe and on page 68 first.
Operation of the sunblind
Open - by pressing (press again - sunshade stops moving)
Close - by pressing (press again - sunshade stops moving)
The sunshade can also be operated by pressing and holding the appropriate
button (starts movement of the sunshade) and releasing it when the sunshade
reaches the desired position.
Activating operation of the sunshade
Read and observe and on page 68 first.
If the operation of sunshade is deactivated (e.g. after disconnecting and con-
necting the battery), then the operation will have to be activated.
›
Switch on the ignition, press and hold the
The sunshade opens and closes again after around 10 seconds.
›
Release the button.
Lights and visibility
Light
Introduction
Unless otherwise stated, the lights only work when the ignition is switched on.
For the basic position of the light switch, use position .
Note
The headlights may mist up temporarily. When the light is switched on, the
light-emitting surface demists after a short period of time.
Operating the lights
Fig. 66
Light switch
To switch on/off the lights, turn the
A
switch to one of the following
positions (equipment-dependent).
Switching off lights (except daytime running lights)
Switching the light on/off automatically
Switching on the parking lights or parking lights on both sides
Switching on the low beam
Headlight range control of the Halogen headlights
The headlight range can be set in Infotainment in the menu
/ → → Light.
The range of the halogen headlights can be set on the screen, in accordance
with the vehicle load, to the following basic settings.
Front seats occupied, boot empty
All seats occupied, boot empty
70
Using the system
-------------------------------------------------------------------------------------------------------------------------------------------------------------
All seats occupied, boot loaded
Driver seat occupied, boot loaded
In the event of another vehicle loading condition, the setting for positions . .
can be used.
The Xenon headlights feature no manual headlight range control. After
switching on the ignition, adjust these automatically to the load and driving
condition of the vehicle.
WARNING
Always adjust the headlight range control to comply with the following
conditions and prevent accidents.
■
The vehicle does not dazzle other road users, especially oncoming vehi-
cles.
■
The beam range is sufficient for safe driving.
Note
■
If, with a dipped beam, the ignition is turned off, then the dipped beam will
automatically switch off and the parking lights will come on. Does not apply to
the position , as long as the conditions are met for the COMING HOME
function . The parking lights are switched off when the ignition key is removed
(for vehicles with the KESSY system, after opening the driver's door).
■
If there is a fault in the light switch, the low beam comes on automatically.
Daytime running lights
The daytime running lights illuminate the area in front of and to the rear of the
vehicle (only applicable for some countries).
The lights are switched on automatically if the following conditions are
met.
The light switch is in the position or .
The ignition is switched on.
WARNING
Always switch on the low beam when visibility is poor.
Note
The light can operate automatically under certain circumstances, even if the
light switch is in position .
Turn signal and main beam
Fig. 67
Operating lever: Turn signal and
main beam operation
Control stalk positions
Switch on the right turn signal
Switch on the left turn signal
Switch on main beam (spring-tensioned position)
Switch off main beam / headlight flasher on (spring-tensioned position)
The main beam can only be switched on when the low beam lights are on.
The headlight flasher can be used even if the ignition is switched off.
The turn signal switches off automatically depending on the steering angle af-
ter turning.
Use the control stalk to switch on/off the headlight assistant
.
Comfort indicating
When the control talk is pressed slightly up or down, the respective turn signal
indicates three times.
If during the convenience turn signal, the operating lever is pressed in the op-
posite direction, the indicating will stop.
Convenience signalling can be activated/deactivated in Infotainment in the
menu
/ → → Light/
WARNING
Only turn on the main beam or the headlight flasher if other road users will
not be dazzled.
71
Lights and visibility
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Note
The setting (activation/deactivation) of the convenience turn signal is stored
(depending on the Infotainment type) in the active user account personalisa-
tion
Automatic driving light control
Fig. 68
Light switch: Position
If the light switch is in position
, then the lights are automatically
switched on/off to suit current light or weather conditions (rain), depending on
the equipment.
If the light switch is in position , the lettering
illuminates next to the
light switch. If the light is switched on automatically, the symbol
also illumi-
nates next to the light switch.
Automatic driving light control in the rain (referred to as function in the
following)
The dipped beam is switched on automatically if the following conditions are
met.
The function is activated.
The light switch is in the position .
The windscreen wipers are on for more than 30 s.
The light turns off automatically about 4 minutes after turning off the wipers.
Setting, activation/deactivation
The following functions can be set or activated/deactivated in Infotainment in
the menu
/ → → Light.
▶
Sensitivity adjustment of the sensor for determining the lighting conditions
for automatic driving light control
▶
Automatic driving light control during rain
WARNING
The automatic driving lamp control (position ) only operates as a sup-
port and does not release the driver from his responsibility to check the
lights and, if necessary, to switch on the light depending on the prevailing
light conditions.
CAUTION
Poorer visibility is evaluated by a sensor mounted below the windscreen in the
holder of the rear-view mirror. Do not cover the sensor - the system can be
affected.
Note
The setting (activate/deactivate) of the automatic driving light control during
rain is stored (depending on the Infotainment type) in the active user account
personalisation
.
Xenon headlight
The Xenon headlights (hereinafter referred to as just system) use the driving
data to automatically ensure the for the best possible light cone in front of the
vehicle.
The system operates automatically in the following modes: urban, extra-urban,
highway, rain, fog, adjusting the lighting direction of the headlights for the
road illumination in curves.
The system works as long as the light switch is in position .
WARNING
If there is a system malfunction the headlights are automatically lowered to
the emergency position, which prevents a possible dazzling of oncoming
traffic. This reduces the cone of light in front of the vehicle. Seek help from
a specialist garage.
72
Using the system
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Fog lights/rear fog light
Fig. 69
Light switch – switch on front
and rear fog lights
Switching on the fog lights/rear fog lights is possible under the following
conditions.
The lights switch is in position , or
.
›
To switch on the fog lights, turn the light switch to position
1
; the warning
light
illuminates in the instrument cluster.
›
To switch on the rear fog lights, pull the light switch to position
2
; the
warning light
illuminates in the instrument cluster.
If the vehicle is not equipped with fog lights, the rear fog lights can be switch-
ed on by pulling the light switch to the only possible setting.
Switch off the fog lights/rear fog lights in reverse order.
Note
If an accessory is connected to the trailer socket, the rear fog lamp does not
light up on the vehicle.
function CORNER
The CORNER function automatically switches on the fog lights on the respec-
tive side of the vehicle (e.g. when cornering or steering), if the following condi-
tions are fulfilled.
The turn signal is turned on or the front wheels are severely locked (in the
event of conflict between the two versions, has turn signal has the higher
priority).
The vehicle speed is below 40 km/h.
The low beam is switched on.
The fog lights are not switched on.
The two fog lights are switched on when you shift into the reverse gear.
COMING HOME / LEAVING HOME
The function COMING HOME ensures that the vehicle's environment is illumi-
nated after switching off the ignition and opening the driver's door.
The function LEAVING HOME ensures that the vehicle's environment is illumi-
nated after unlocking the vehicle with the radio remote control unit.
The function switches the light on only if there is poorer visibility and the light
switch is in the position .
The two functions can be used in Infotainment in the menu
/ → → Light
(activated/deactivated and adjusted).
CAUTION
■
Poorer visibility is evaluated by a sensor mounted below the windscreen in
the holder of the rear-view mirror. Do not cover the sensor - the system can
be affected.
■
If this option is always enabled, then the battery is heavily loaded.
Note
The setting of the two functions is stored (depending on the Infotainment
type) in the active user account personalisation
.
Hazard warning light system
Fig. 70
Button for hazard warning light
system
›
To switch on/off, press the
button
.
When switching on, all the turn signal lights as well as the warning light
in
the button flash simultaneously with the control lights
in the instrument
cluster.
73
Lights and visibility
-------------------------------------------------------------------------------------------------------------------------------------------------------------
The hazard warning light system can also be operated if the ignition is switch-
ed off.
If one of the airbags is deployed, the hazard warning light system will switch
on automatically.
The automatic activation of hazard warning lights can take place during a
heavy braking. After starting or accelerating the hazard warning system is au-
tomatically switched off.
When the hazard warning system is on and the turn signal is switched on, the
hazard warning lights are switched off temporarily and only the turn signal
flashes on the relevant side of the vehicle.
Parking light
The side light is provided for lighting of the parked vehicle.
Switching on the side light on one side
›
Switch off the ignition.
›
Press the control lever all the way into position or until it stops
The parking lights on the respective side of the vehicle are turned on.
Switching on the side light on both sides
›
Turn the ignition on and turn the light switch to position
.
›
Switch off the ignition and lock the car.
After removing the ignition key and opening the driver's door, an audible warn-
ing sounds. After a few seconds, or after closing the driver's door, the acoustic
warning signal stops.
CAUTION
■
Turning on the parking light means the battery is heavily loaded.
■
The parking lights may switch off automatically due to a low battery charge.
If the two-sided parking lights are switched on when the ignition is off, the
parking lights will not switch on automatically.
Entry space lighting
The lighting is positioned on the lower edge of the exterior mirror and illumi-
nates the entry area of the front door.
The lighting switches on after unlocking or opening the vehicle door (depend-
ing on the lighting conditions).
The lighting switches off after around 30 seconds after closing the front door
or switching on the ignition.
Driving abroad
When driving in countries with opposing traffic system (traffic on the
left/right), headlights may dazzle oncoming traffic.
Therefore, the Xenon headlight setting must be adapted by turning on travel
mode in infotainment in the menu
/ → → Light menu. In this mode, no
automatic beam adjustment is made ahead of the vehicle.
Headlight Assist (Light Assist / Dynamic Light Assist)
Introduction
Fig. 71
Sensor window for the head-
light assistant
The headlight assistant (referred to as just system in the following) automati-
cally switches the main beam on/off, if necessary, adjusts the beam of the
front headlights in accordance with the existing traffic situation (other vehi-
cles) and environmental conditions (e.g. driving through a lit village).
The switching on/off of the main beam, if necessary, the adaptation of the
headlight, is controlled by a sensor
.
Depending on the equipment, the following system versions can exist.
Light Assist automatically switches the main beam on/off.
Dynamic Light Assist automatically adjusts the light cone shape of the front head-
lights in order to prevent dazzling the oncoming and preceding vehicles, while
ensuring the highest possible illumination of the road edges.
74
Using the system
-------------------------------------------------------------------------------------------------------------------------------------------------------------
If the driving mode Eco
, Select the driving mode (Driving Mode
Selection) or travel mode
, Driving abroad is selected, the automatic
adjustment of the beam is deactivated, Dynamic Light Assist only switches the
main beam on/off automatically.
If the Xenon headlights are in the mode rain or fog
, then Dynamic Light
Assist is deactivated.
If there is a fault, the error message will appear in the instrument cluster dis-
play. Seek help from a specialist garage.
WARNING
The system is used only for support, thus the driver is not released from his
obligation to manually adjust the main or low beam according to the given
ambient conditions (e.g. in unfavourable lighting and weather conditions, as
when passing poorly lit road users, if necessary, when the area in front of
the sensor is covered by an obstacle).
CAUTION
Do not attach any stickers or similar objects in front of the sensor on the wind-
screen to avoid impairing the function of the system.
Note
The adjustment of the headlight assistant in Infotainment is stored (depending
on the Infotainment type) in the active user account personalisation
Operating conditions
Read and observe and on page 75 first.
The system works under the following conditions.
The system is activated in Infotainment in the menu
/ → → light
activated.
The light switch is in the position .
The system is activated
The vehicle speed is over 60 km/h or for some countries more than 40
km/h.
The windscreen is clean in the sensor area.
System on/off
Fig. 72
Operating lever: Headlamp as-
sistant
Read and observe and on page 75 first.
Switch on the system
›
Push the lever into the sprung position
A
light lights up in the instrument cluster display.
Switch off the system
›
If the high beam is switched on automatically, move the lever into the sprung
position
B
. The warning light goes out. The high beam turns off.
›
If the high beam is is not switched on automatically, move the lever into the
sprung position
A
. The warning light goes out. The high beam turns on.
The high beam switches off automatically when the speed falls below 30 km/h
(but the system remains switched on).
Interior lighting
Introduction
The inner lighting also works if the ignition is switched off. With the ignition
off (or after a door is opened),the lights will automatically switch off after ap-
proximately 10 minutes.
75
Lights and visibility
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Operation of the lights from the front seats
Fig. 73
Operation of the lights from the
front seats
Switch on/off (by pressing the relevant switch)
Automatic operation
Rear lighting
Depending on equipment fitted:
▶
Reading light left
▶
Front and rear lighting
Reading light right
Automatic operation - switch
The system is turned on when any of the following is present.
▶
The vehicle is unlocked.
▶
One of the doors is opened.
▶
The ignition key is removed.
The system is turned off when any of the following is present.
▶
The vehicle is locked.
▶
The ignition is switched on.
▶
About 30 seconds after all the doors have been closed.
A
B
C
D
Interior light, rear
Fig. 74
Interior lights at the rear: Variant
1
Fig. 75 Interior lights at the rear: Version 2/version 3
The rear lighting (variants 1 and 3) is controlled together with the automatic
operation of the lighting from the front seats.
Variant 1 - switch on/off (by pressing the relevant switch)
Reading light left
Reading light right
Variant 2 - operation (by moving the light lens
C
)
Switching on
Switching off
Automatic operation (the light is switched on/off automatically together
with the front light)
Variant 3 - switch on/off (by pressing the relevant switch)
Reading light left
Reading light right
A
B
D
76
Using the system
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст