Infiniti M35 (2010 year). Manual — part 7
RAIN-SENSING AUTO WIPER SYSTEM
The rain-sensing auto wiper system can auto-
matically turn on the wipers and adjust the
wiper speed depending on the rainfall and the
vehicle speed by using the rain sensor located
on the upper part of the windshield.
To set the rain-sensing auto wiper system, push
the lever down to the INT (intermittent) position
s
1
. The wiper will sweep once while the ignition
switch is in the ON position.
The rain sensor sensitivity level can be adjusted
by turning the knob toward the front
s
2
(High)
or toward the rear
s
3
(Low).
● High — High sensitive operation
● Low — Low sensitive operation
To turn the rain-sensing auto wiper system off,
push up the lever to the OFF position, or pull
down the lever to the LO or HI position.
CAUTION
Do not touch the rain sensor and around it when
the wiper switch is in the INT position and the
ignition switch is in the ON position. The wipers
may operate unexpectedly and cause to an in-
jury or a wiper damage.
● The rain-sensing auto wipers are intended for
use during rain. If the switch is left in the INT
position, the wipers may operate unexpect-
edly when dirt, fingerprints, oil film or insects
are stuck on or around the sensor. The wipers
may also operate when exhaust gas or mois-
ture affect the rain sensor.
● The rain-sensing auto wipers may not oper-
ate if rain does not hit the rain sensor even if
it is raining.
To defog/defrost the rear window glass and
outside mirrors (if so equipped with defroster),
start the engine and push the switch on. The
indicator light
s
1
will come on. Push the switch
again to turn the defroster off.
It will automatically turn off in approximately 15
minutes.
CAUTION
When cleaning the inner side of the rear win-
dow, be careful not to scratch or damage the
rear window defroster.
SIC3887
SIC2767B
REAR WINDOW AND OUTSIDE MIRROR
DEFROSTER SWITCH
2-28
Instruments and controls
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
XENON HEADLIGHTS
WARNING
HIGH VOLTAGE
● When xenon headlights are on, they produce
a high voltage. To prevent an electric shock,
never attempt to modify or disassemble. Al-
ways have your xenon headlights replaced
at an INFINITI retailer.
● Xenon headlights provide considerably
more light than conventional headlights. If
they are not correctly aimed, they might
temporarily blind an oncoming driver or the
driver ahead of you and cause a serious acci-
dent. If headlights are not aimed correctly,
immediately take your vehicle to an INFINITI
retailer and have the headlights adjusted
correctly.
When the xenon headlight is initially turned on,
its brightness or color varies slightly. However,
the color and brightness will soon stabilize.
● The life of xenon headlights will be shortened
by frequent on-off operation. It is generally
desirable not to turn off the headlights for
short intervals (for example, when the ve-
hicle stops at a traffic signal). Even when the
daytime running lights are active (Canada
only), the xenon headlights do not turn on.
This way the life of the xenon headlights is
not reduced.
● If the xenon headlight bulb is close to burn-
ing out, the brightness will drastically de-
crease, the light will start blinking, or the
color of the light will become reddish. If one
or more of the above signs appear, contact an
INFINITI retailer.
HEADLIGHT SWITCH
Lighting
s
1
Turn the switch to the
position:
The front park, side marker, tail, license
plate and instrument lights will come on.
s
2
Turn the switch to the
position:
Headlights will come on and all the other
lights remain on.
SIC2411
HEADLIGHT AND TURN SIGNAL SWITCH
Instruments and controls
2-29
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Autolight system
The autolight system allows the headlights to
be set so they turn on and off automatically.
To set the autolight system:
1. Make sure the headlight switch is in the
AUTO position
s
1
.
2. Push the ignition switch to the ON posi-
tion.
3. The autolight system automatically turns
the headlights on and off.
To turn the autolight system off, turn the switch
to the OFF,
or
position.
The autolight system can turn on the headlights
automatically when it is dark and turn off the
headlights when it is light.
If the ignition switch is pushed to the LOCK
position and one of the doors is opened and
this condition is continued, the headlights re-
main on for 5 minutes.
Automatic headlights off delay :
You can keep the headlights on for up to 180
seconds after you push the ignition switch to
LOCK and open any door then close all the
doors.
You can adjust the period of the automatic
headlights off delay from 0 seconds (OFF) to 180
seconds.
For automatic headlights off delay setting, see
“Comfort & Conv. settings” in the “4. Monitor,
climate, audio, phone and voice recognition
systems” section.
Be sure not to put anything on top of the photo
sensor
s
A
located on the top of the instrument
panel. The photo sensor controls the autolight;
if it is covered, the photo sensor reacts as if it is
dark and the headlights will illuminate.
SIC2412
SAA0642A
2-30
Instruments and controls
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Headlight beam select
s
1
To select the low beam, put the lever in
the neutral position as shown.
s
2
To select the high beam, push the lever
forward while the switch is in the
position. Pull it back to select the low
beam.
s
3
Pulling the lever toward you will flash the
headlight high beam even when the
headlight switch is in the OFF position.
Battery saver system
● When the headlight switch is in the
or
position while the ignition switch is in
the ON position, the lights will automatically
turn off 5 minutes after the ignition switch
has been pushed to the LOCK position.
● When the headlight switch remains in the
or
position after the lights
automatically turn off, the lights will turn on
when the ignition switch is pushed to the ON
position.
CAUTION
● When you turn on the headlight switch again
after the lights automatically turn off, the
lights will not turn off automatically. Be sure
to turn the light switch to the OFF position
when you leave the vehicle for extended pe-
riods of time, otherwise the battery will be
discharged.
● Never leave the light switch on when the
engine is not running for extended periods of
time even if the headlights turn off
automatically.
Daytime running light system
(Canada only)
The daytime running lights automatically illumi-
nate when the engine is started with the park-
ing brake released. The daytime running lights
operate with the headlight switch in the OFF
position or in the
position. Turn the
headlight switch to the
position for full
illumination when driving at night.
If the parking brake is applied before the engine
is started, the daytime running lights do not
illuminate. The daytime running lights illumi-
nate once the parking brake is released. The
daytime running lights will remain on until the
ignition switch is pushed to the LOCK position.
WARNING
When the daytime running light system is ac-
tive, tail lights on your vehicle are not on. It is
necessary at dusk to turn on your headlights.
Failure to do so could cause an accident injur-
ing yourself and others.
Adaptive Front lighting System (AFS)
The Adaptive Front lighting System (AFS) will
automatically adjust the headlights (low beam)
toward the turning direction to improve the
driver’s view. When the headlight switch is ON
and the driver operates the steering wheel in a
turn, the AFS system will be activated.
The AFS will operate:
● when the headlight switch is ON.
SIC2413
Instruments and controls
2-31
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
● when the selector lever is in any position
other than P (Park) or R (Reverse).
● when the vehicle is driven at above 16 MPH
(25 km/h) for the left-side headlight. Note
that the right-side low beam headlight will
swivel but the left side will not swivel when
the vehicle is at a stop and the steering
wheel is turned. The vehicle must attain a
speed above 16 MPH (25 km/h) before AFS
activates the left-side headlight.
To turn the AFS off, push the OFF side of the AFS
switch. (The AFS OFF indicator light will illumi-
nate.) Push the ON side of the switch to turn the
system on again.
AFS will also adjust the headlight to a proper
axis automatically, depending on the number of
occupants in the vehicle, the load the vehicle is
carrying and the road conditions.
If the AFS OFF indicator light blinks after the
ignition switch has been pushed to the ON
position, this may indicate that the AFS is not
functioning properly. Have the system checked
by an INFINITI retailer. When the engine is
started, the headlights will vibrate to check the
system condition. This is not a malfunction.
Instrument brightness control
The instrument brightness control operates
when the light switch is in the AUTO (when
lighting),
or
position with the
ignition switch in the ON position.
Turn the control to the darkening direction
s
1
or the brightening direction
s
2
to adjust the
brightness of instrument panel lights.
When the control is turned to the upper end, the
light intensity will be at maximum. When the
control is turned to the lower end, the light will
be turned off.
SIC2645
SIC3554
2-32
Instruments and controls
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
TURN SIGNAL SWITCH
s
1
Turn signal
Move the lever up or down to signal the turning
direction. When the turn is completed, the turn
signals cancel automatically.
s
2
Lane change signal
To indicate a lane change, move the lever up or
down to the point where lights begin flashing.
FOG LIGHT SWITCH
To turn the fog lights on, turn the headlight
switch to the
position, then turn the
switch to the
position. To turn them off,
turn the switch to the OFF position.
The headlights must be on for the fog lights to
operate.
Push the switch on to warn other drivers when
you must stop or park under emergency condi-
tions. All turn signal lights will flash.
WARNING
● If stopping for an emergency, be sure to
move the vehicle well off the road.
● Do not use the hazard warning flashers while
moving on the highway unless unusual cir-
cumstances force you to drive so slowly that
your vehicle might become a hazard to other
traffic.
● Turn signals do not work when the hazard
warning flasher lights are on.
SIC2231
SIC2465
SIC2574
HAZARD WARNING FLASHER SWITCH
Instruments and controls
2-33
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
The flasher can be actuated with the ignition
switch in any position.
Some state laws may prohibit the use of the
hazard warning flasher switch while driving.
To sound the horn, push the center pad area of
the steering wheel.
WARNING
Do not disassemble the horn. Doing so could
affect proper operation of the supplemental
front air bag system. Tampering with the
supplemental front air bag system may result
in serious personal injury.
CAUTION
● The battery could run down if the seat heater
is operated while the engine is not running.
● Do not use the seat heater for extended pe-
riods or when no one is using the seat.
● Do not put anything on the seat which insu-
lates heat, such as a blanket, cushion, seat
cover, etc. Otherwise, the seat may become
overheated.
● Do not place anything hard or heavy on the
seat or pierce it with a pin or similar object.
This may result in damage to the heater.
● Any liquid spilled on the heated seat should
be removed immediately with a dry cloth.
● When cleaning the seat, never use gasoline,
thinner, or any similar materials.
● If any malfunctions are found or the heated
seat does not operate, turn the switch off
and have the system checked by an INFINITI
retailer.
SIC2769
HORN
HEATED SEATS (rear seats) (if so
equipped)
2-34
Instruments and controls
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
The rear outboard seats are warmed by built-in
heaters. The switches located on the inside of
the rear center armrest can be operated inde-
pendently of each other.
1. Start the engine.
2. Select heat range.
s
1
For high heat, push the HI (High) side of
the switch.
s
2
For low heat, push the LO (Low) side of
the switch.
The indicator light in the switch
s
3
will
illuminate when low or high is selected.
3. To turn off the heater, push the HI or LO
side (which is selected) of the switch.
Make sure the indicator light turns off.
The heater is controlled by a thermostat,
automatically turning the heater on and off.
The indicator light will remain on as long as
the switch is on.
When the vehicle’s interior is warmed, or
before you leave the vehicle, be sure to turn
off the switch.
The climate controlled seat warms up or cools
down the front seats by blowing warm or cool
air from the surface of the seat. The switches
located on the center console can be operated
independently of each other.
1. Start the engine.
2. Turn the control knob
s
A
to the H (Heat)
side
s
1
or to the C (Cool) side
s
2
. The
indicator light
s
B
on the control knob will
illuminate.
3. Adjust the desired amount of the air using
the control knob
s
A
.
The climate controlled seat blower remains
on low speed for approximately 60 seconds
after turning the switch on or selecting the
desired temperature.
SIC2770
SIC2771
CLIMATE CONTROLLED SEATS (front seats)
Instruments and controls
2-35
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
4. When the vehicle’s interior is warmed or
cooled, and/or before you leave the ve-
hicle, be sure to turn the control knob to
the OFF position (center). The indicator
light
s
B
on the control knob goes off at
the OFF position.
To check the air filter for the climate con-
trolled seat, contact an INFINITI retailer.
CAUTION
● The battery could run down if the climate
controlled seat is operated while the engine
is not running.
● Do not use the climate controlled seat for
extended periods or when no one is using
the seat.
● Do not put anything on the seat which insu-
lates heat, such as a blanket, cushion, seat
cover, etc. Otherwise, the seat may become
overheated.
● Do not place anything hard or heavy on the
seat or pierce it with a pin or similar object.
This may result in damage to the climate
controlled seat.
● Any liquid spilled on the seat should be re-
moved immediately with a dry cloth.
● The climate controlled seat has an air filter.
Do not operate climate controlled seat with-
out an air filter. This may result in damage to
the system.
● When cleaning the seat, never use gasoline,
thinner, or any similar materials.
● If any malfunctions are found or the climate
controlled seat does not operate, turn the
switch off and have the system checked by
an INFINITI retailer.
The Lane Departure Warning (LDW) system will
sound a warning chime and blink the lane
departure warning light
(orange) to alert
the driver if the vehicle is traveling close to
either the left or the right of a traveling lane
with detectable lane markers.
The LDW system activates automatically when
the ignition switch is pushed to the ON posi-
tion. (This is the automatic setting mode.) The
LDW ON indicator
s
1
on the switch will illumi-
nate.
To cancel the LDW system, push the LDW switch
to turn off the system. The LDW ON indicator
s
1
will turn off.
SSD0671
LANE DEPARTURE WARNING (LDW) SWITCH
(if so equipped)
2-36
Instruments and controls
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Push the LDW switch again to turn the LDW
system on. The LDW automatic setting mode
can be changed to the manual setting mode. To
change the mode, push and hold the LDW
switch for more than 4 seconds when the LDW
ON indicator is off. In the manual setting mode,
push the LDW switch on and off to turn the LDW
system on and off.
See “LANE DEPARTURE WARNING (LDW)
SYSTEM/LANE DEPARTURE PREVENTION (LDP)
SYSTEM” in the “5. Starting and driving” sec-
tion for more details.
For driving or starting the vehicle on snowy
roads or slippery areas, turn on the SNOW
mode switch. The indicator light
s
1
on the
switch will illuminate. When the SNOW mode is
activated, engine output is controlled to avoid
wheel spin.
Turn off the SNOW mode for normal driving.
The vehicle should be driven with the Vehicle
Dynamic Control (VDC) system on for most
driving conditions.
If the vehicle is stuck in mud or snow, the VDC
system reduces the engine output to reduce
wheel spin. The engine speed will be reduced
even if the accelerator is depressed to the floor.
If maximum engine power is needed to free a
stuck vehicle, turn the VDC system off.
To turn off the VDC system, push the VDC OFF
switch. The
indicator will illuminate.
Push the VDC OFF switch again or restart the
engine to turn on the system. (See “VEHICLE
DYNAMIC CONTROL (VDC) SYSTEM” in the “5.
Starting and driving” section.)
SIC3602
SIC1881
SNOW MODE SWITCH (if so equipped)
VEHICLE DYNAMIC CONTROL (VDC) OFF
SWITCH
Instruments and controls
2-37
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
If the power supply is disconnected, the clock
will not indicate the correct time. Readjust the
time.
ADJUSTING THE TIME
1. To set the clock forward, push the button
s
1
.
2. To set the clock backward, push the but-
ton
s
2
.
3. To move forward or backward faster, push
and hold the button more than 5 seconds.
For details about display clock adjustment (if so
equipped), see “HOW TO USE SETTING BUTTON”
in the “4. Monitor, climate, audio, phone and
voice recognition systems” section.
The power outlets are located on the back side
and inside (if equipped) of the center console
for powering electrical accessories such as a
cellular telephone.
CAUTION
● The outlet and plug may be hot during or
immediately after use.
● Do not use with accessories that exceed a 12
volt, 120W (10A) power draw. Do not use
double adapters or more than one electrical
accessory.
● Use power outlet with the engine running to
avoid discharging the vehicle battery.
● Avoid using power outlet when the air condi-
tioner, headlights or rear window defroster
is on.
● This power outlet is not designed for use
with a cigarette lighter unit.
● Push the plug in as far as it will go. If good
contact is not made, the plug may overheat
or the internal temperature fuse may open.
● Before inserting or disconnecting a plug, be
sure the electrical accessory being used is
turned OFF.
● When not in use, be sure to close the cap. Do
not allow water to contact the outlet.
SIC2772
SIC2773
Only for model without DVD player
SIC2774
CLOCK
POWER OUTLETS
2-38
Instruments and controls
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
FRONT
To open the ashtray lid, push the lid down and
release it
s
1
.
To empty the ashtray, pull out
s
2
.
The cigarette lighter operates when the ignition
switch is in the ON position.
Push the lighter in all the way
s
3
, then release
it. When the lighter is heated, it will spring out.
Return the lighter to its original position after
use.
CAUTION
● The cigarette lighter socket is a power
source for the cigarette lighter element only.
The use of the cigarette lighter socket as a
power source for any other accessory is not
recommended.
● Do not use any other power outlet for an
accessory lighter.
REAR
To open the ashtray lid, pull
s
1
.
To empty the ashtray, and pull out
s
2
.
SIC2775B
SIC3693
CIGARETTE LIGHTER AND ASHTRAYS
Instruments and controls
2-39
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CUP HOLDERS
CAUTION
● Avoid abrupt starting and braking when the
cup holder is being used to prevent spilling
the drink. If the liquid is hot, it can scald you
or your passenger.
● Use only soft cups in the cup holder. Hard
objects can injure you in an accident.
Front
To open the cup holder, push the lid down and
release it
s
1
.
To remove the inner tray for cleaning, pull it up
as illustrated
s
2
.
Rear
Type A :
Push the button as illustrated on the rear center
armrest to use the cup holder.
Front
SIC2777B
Rear — Type A
SIC2778B
STORAGE
2-40
Instruments and controls
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Type B :
Open the lid of the rear center armrest to use
the cup holder.
SUNGLASSES HOLDER
WARNING
Keep the sunglasses holder closed while driv-
ing to prevent an accident.
To open the sunglasses holder, push
s
1
.
CAUTION
● Do not use for anything other than glasses.
● Do not leave glasses in the sunglasses
holder while parking in direct sunlight. The
heat may damage the glasses.
GLOVE BOX
WARNING
Keep glove box lid closed while driving to help
prevent injury in an accident or a sudden stop.
To open the glove box, push the glove box lid
release button
s
1
.
To close, push the lid in until the lock latches.
To lock
s
2
/unlock
s
3
the glove box, use the
mechanical key. For the mechanical key usage,
see “KEYS” in the “3. Pre-driving checks and
adjustments” section.
Rear — Type B
SIC2875
SIC2779B
SIC2930A
Instruments and controls
2-41
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CONSOLE BOX
Model with DVD player
To open the console box lid, pull the lever
s
1
.
To close, push the lid down until the lock
latches.
Model without DVD player
To open the console box lid, pull the lever
s
2
or
s
3
and pull up the lid.
When the lever
s
2
(driver’s seat side) is pulled,
the upper case is available for storing some
small items. When the lever
s
3
(front passen-
ger’s seat side) is pulled, the bottom case is
available for storing some larger ones.
To close, push the lid down until the lock
latches.
Model with DVD player
SIC2781A
Model without DVD player
SIC2782A
2-42
Instruments and controls
w
—
—
05/19/09—tbrooks
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
COAT HOOKS
The coat hooks are equipped beside the rear
personal lights.
To use the coat hook, push the hook
s
A
to
release.
CAUTION
Do not place items which are more than 2 lb (1
kg) on the hook.
CARGO NET (if so equipped)
The cargo net helps keep packages in the cargo
area from moving around while your vehicle is
driven.
To install the cargo net, attach the hooks to the
retainers
s
A
.
CAUTION
Avoid keeping heavy objects in the net.
POWER WINDOWS
WARNING
● Make sure that all passengers have their
hands, etc. inside the vehicle while it is in
motion and before closing the windows. Use
the window lock switch to prevent unex-
pected use of the power windows.
● Do not leave children unattended inside the
vehicle. They could unknowingly activate
switches or controls and become trapped in
the window. Unattended children could be-
come involved in serious accidents.
The power windows operate when the ignition
switch is in the ON position or for about 45
seconds after the ignition switch is pushed to
the LOCK position. If the driver’s or front pas-
senger’s door is opened during this period of
about 45 seconds, power to the windows is
canceled.
SIC2077A
SIC2784
WINDOWS
Instruments and controls
2-43
w
—
—
05/14/09—pattie
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст