Infiniti M35/M45 Y50. Manual — part 801
GW-1
GLASSES, WINDOW SYSTEM & MIRRORS
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION
GW
A
B
GW
GLASSES, WINDOW SYSTEM & MIRRORS
PRECAUTIONS . . . . . . . . . . . . . . .. 3
Handling for Adhesive and Primer . . . . . . ... 3
PREPARATION . . . . . . . . . . . . . . ... 4
Special Service Tools . . . . . . . . . . . ... 4
Commercial Service Tools . . . . . . . . . . 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES . . 5
Work Flow . . . . . . . . . . . . . . . . 5
Generic Squeak and Rattle Troubleshooting . . ... 7
Diagnostic Worksheet . . . . . . . . . . . .. 9
WINDSHIELD GLASS . . . . . . . . . . . ...11
Removal and Installation . . . . . . . . . . .11
REMOVAL . . . . . . . . . . . . . . . 11
INSTALLATION . . . . . . . . . . . . ... 12
POWER WINDOW SYSTEM . . . . . . . . . 14
Component Parts and Harness Connector Location
GW-2
SIDE WINDOW GLASS . . . . . . . . . . . 57
Removal and Installation . . . . . . . . . . 57
REMOVAL . . . . . . . . . . . . . . ... 57
INSTALLATION . . . . . . . . . . . . . 58
REAR WINDOW GLASS AND MOLDING . . . . 59
Removal and Installation . . . . . . . . . . 59
REMOVAL . . . . . . . . . . . . . . ... 59
INSTALLATION . . . . . . . . . . . . . 60
FRONT DOOR GLASS AND REGULATOR . . . . 61
Removal and Installation . . . . . . . . . . 61
DOOR GLASS . . . . . . . . . . . . . . 61
REGULATOR ASSEMBLY . . . . . . . . .. 62
Disassembly and Assembly . . . . . . . . . 63
REGULATOR ASSEMBLY . . . . . . . . .. 63
Inspection after Installation . . . . . . . . . . 63
REAR DOOR GLASS AND REGULATOR . . . ... 65
Removal and Installation . . . . . . . . . . 65
DOOR GLASS . . . . . . . . . . . . . . 65
REGULATOR ASSEMBLY . . . . . . . . .. 66
Disassembly and Assembly . . . . . . . . . 68
REGULATOR ASSEMBLY . . . . . . . . .. 68
Inspection after Installation . . . . . . . . . . 68
INSIDE MIRROR . . . . . . . . . . . . . ... 69
Wiring Diagram –I/MIRR– . . . . . . . . . ... 69
Removal and Installation . . . . . . . . . . 70
REMOVAL . . . . . . . . . . . . . . ... 70
INSTALLATION . . . . . . . . . . . . . 70
REAR WINDOW DEFOGGER . . . . . . . . .. 71
CONSULT-II Function (IPDM E/R) . . . . . . .. 81
CONSULT-II START PROCEDURE . . . . . 81
DATA MONITOR . . . . . . . . . . . . .. 81
ACTIVE TEST . . . . . . . . . . . . . ..81
Check Filament . . . . . . . . . . . . . ...92
Filament Repair . . . . . . . . . . . . . ...92
REPAIR EQUIPMENT . . . . . . . . . . .92
REPAIRING PROCEDURE . . . . . . . . .93
REVERSE INTERLOCK DOOR MIRROR SYSTEM ...94
Component Parts and Harness Connector Location ...94
System Description . . . . . . . . . . . . .94
DOOR MIRROR . . . . . . . . . . . . . ...118
REMOVAL . . . . . . . . . . . . . . .. 118
INSTALLATION . . . . . . . . . . . . .. 118
Disassembly and Assembly . . . . . . . . .. 119
DISASSEMBLY . . . . . . . . . . . . .. 119
ASSEMBLY . . . . . . . . . . . . . . 120
PRECAUTIONS
GW-3
C
D
E
F
G
H
J
K
L
M
A
B
GW
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NIS00216
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Procedures without Cowl Top Cover
NIS00217
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Handling for Adhesive and Primer
NIS00218
●
Do not use an adhesive which is past its usable date. Shelf life of this product is limited to six months after
the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the box.
●
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
●
Open the seal of the primer and adhesive just before application. Discard the remainder.
●
Before application, be sure to shake the primer container to stir the contents. If any floating material is
found, do not use it.
●
If any primer or adhesive contacts the skin, wipe it off with gasoline or equivalent and wash the skin with
soap.
●
When using primer and adhesive, always observe the precautions in the instruction manual.
PIIB3706J
GW-4
PREPARATION
PREPARATION
PFP:00002
Special Service Tools
NIS00219
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
NIS0021A
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locating the noise
(J-43980)
NISSAN Squeak and
Rattle Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locating the noise
Suction lifter
Holding the door glass
SIIA0995E
PIIB1805J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст