Infiniti M35/M45 Y50. Manual — part 1142
TROUBLE DIAGNOSES
WT-15
C
D
F
G
H
I
J
K
L
M
A
B
WT
TEWT0048E
WT-16
TROUBLE DIAGNOSES
TEWT0042E
TROUBLE DIAGNOSES
WT-17
C
D
F
G
H
I
J
K
L
M
A
B
WT
Low Tire Pressure Warning Control Unit Input/Output Signal Standard
NES000JX
CAUTION:
When checked using a circuit tester for voltage measurement, connector terminals should not be
forcefully extended.
Terminal
Measuring point
Measuring condition
Standard
+
(wire color)
–
2 (B/R)
Ground
Ignition switch
Ignition switch ON
Battery voltage (12 V)
5 (W/R)
Tire pressure warning check
connector
Always
Approx. 5 V
7 (LG)
Battery power supply
Ignition switch ON
Battery voltage (12 V)
8 (R/W)
9 (GR)
10 (SB)
11 (W/G)
Signal Input
Approx. 4.5 V
12 (R)
13 (L)
14 (L/G)
15 (L)
CAN-H
—
—
16 (P)
CAN-L
—
—
17 (B)
Ground
—
0 V
19 (G/R)
Hazard
Hazard lamp switch OFF
Battery voltage (Approx. 12 V)
Hazard lamp switch ON
0 V
23 (BR)
Ground
—
0 V
24 (W/L)
—
0 V
25 (B/R)
—
0 V
26 (V)
—
0 V
27 (O)
Analog signal
Ignition switch ON
Approx. 0.7 V
28 (G)
29 (P)
30 (L/R)
WT-18
TROUBLE DIAGNOSES
ID Registration Procedure
NES000JY
ID REGISTRATION WITH ACTIVATION TOOL
This procedure must be done after replacement of a tire pressure transmitter, low tire pressure warn-
ing control unit, or tire rotation.
1.
Perform “CONSULT-II Start Procedure”. Refer to
GI-38, "CONSULT-II Start Procedure"
2.
Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3.
Touch “ID REGIST” on “SELECT WORK ITEM”.
4.
With the activation tool (J-45295) pushed against the front-left
tire pressure transmitter position of the tire air valve, press and
hold the button for 5 seconds.
5.
Register the IDs in order from FR LH, FR RH, RR RH, RR LH.
When ID registration of each wheel has been completed, turn
signal lamp blinks.
6.
After completing all ID registrations, press “END” to complete the procedure.
NOTE:
Be sure to register the IDs in order from FR LH, FR RH, RR RH, to RR LH, or the self-diagnosis results
display will not function properly.
ID REGISTRATION WITHOUT ACTIVATION TOOL
This procedure must be done after replacement of a tire pressure transmitter, low tire pressure warn-
ing control unit, or tire rotation.
1.
Perform “CONSULT-II Start Procedure”. Refer to
GI-38, "CONSULT-II Start Procedure"
2.
Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3.
Touch “ID REGIST” on “SELECT WORK ITEM”.
4.
Adjust the tire pressure to the values shown in the table below for ID registration, and drive the vehicle at
40 km/h (25 MPH) or more for a few minutes.
5.
After completing all ID registrations, press “END” to complete the procedure.
6.
Inflate all tires to proper pressure. Refer to
WT-41, "SERVICE DATA AND SPECIFICATIONS (SDS)"
.
SEIA0460E
Activation tire position
Turn signal lamp
CONSULT-II
1
Front LH
2 times flashing
“YET”
↓
“DONE”
2
Front RH
3
Rear RH
4
Rear LH
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front LH
240 (2.4, 34)
Front RH
220 (2.2, 31)
Rear RH
200 (2.0, 29)
Rear LH
180 (1.8, 26)
Activation tire position
CONSULT-II
Front LH
“YET”
↓
“DONE”
Front RH
Rear RH
Rear LH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст