Infiniti M35/M45 Y50. Manual — part 1093
FRONT SEAT
SE-169
C
D
E
F
G
H
J
K
L
M
A
B
SE
Disassembly and Assembly
NIS0028H
SEATBACK
Disassembly
1.
Remove seatback trim and seatback pad.
NOTE:
Seatback trim and seatback pad can be removed without removing seatback assembly from seat body.
●
Remove the retainer from the lower side of seatback board.
●
Disconnect the clips and pawls, and then remove the seatback
board.
: Pawl
: Clip
●
Remove the seatback hinge mounting bolts.
●
Remove the retainer on the back side of the seatback.
●
Remove the seat speaker grills. (Applied 5.1 ch BOSE studio surround® system models.) Refer to
●
Remove the headrest holder.
CAUTION:
Before installing headrest holder, check its orientation
(front/rear and right/left).
●
Disconnect the clip, and then remove the reclining device cover.
●
Remove the screws, and then remove the seatback upper fin-
isher.
PIIB3344J
PIIB3353J
PIIB4084J
PIIB3355J
SE-170
FRONT SEAT
●
Remove the bracket mounting nuts.
●
Remove seatback trim and pad from seatback frame.
●
Remove the hog rings to separate the trim and pad.
2.
Remove seatback frame.
●
Remove seat speaker. (Applied 5.1 ch BOSE studio surround® system models) Refer to
.
●
Remove the bands, and then remove seatback thermal electrical device (TED) assembly.
●
Remove the seat harness assembly from seatback assembly.
●
Remove the bolts, and then remove seatback frame from seat cushion frame.
Assembly
Assemble in the reverse order of disassembly. Be careful of the following one point.
Install the hog rings of seat cushion trim in position, and then
securely connect the trim or trim code with the pad side wire.
SEAT CUSHION
Disassembly
1.
Remove the seatback trim and seatback pad.
●
Remove the retainer from the lower side of seatback board.
●
Disconnect the clip and pawl, and then remove seatback
board.
: Pawl
: Clip
●
Remove the screws and disconnect the clips, and then
remove the seat cushion rear finisher. (Climate controlled
seat model)
PIIB3356J
PIIB3344J
PIIB3345J
FRONT SEAT
SE-171
C
D
E
F
G
H
J
K
L
M
A
B
SE
●
Remove the seat cushion front finisher.
: Pawl
: Clip
●
Remove the seat reclining switch knob and seat slide switch
knob.
●
Pull seat cushion outer finisher forward, and then disconnect
the pawls and clips.
: Pawl
: Clip
●
Lift the rear part of the seat cushion outer finisher backward,
and then remove the seat cushion outer finisher.
●
Remove the harness connector clamp of lumber support switch.
●
Removal the lumber support switch.
●
Remove the seat cushion inner finisher.
: Pawl
●
Remove the retainers from the lower side of front seat. (Driver's seat only)
●
Remove the hog rings to separate the trim and pad. (Driver's seat only)
2.
Remove the nuts, and then remove the seat cushion frame. (Driver's seat only)
3.
Remove each unit which is attached to seat cushion frame and seat adjuster assembly.
●
Remove the screws, and then remove the climate controlled seat control unit.
●
Remove the screws, and then remove the blower motor.
●
Remove the bands, and then remove the seat cushion thermal electrical device (TED) assembly.
PIIB3346J
PIIB3348J
PIIB3350J
PIIB3351J
SE-172
FRONT SEAT
●
Remove driver's seat control unit. (Driver's seat only)
●
Remove the driver seat control switch.
●
Remove seat cushion finisher B and seat cushion finisher C.
●
Remove seat harnesses.
Assembly
Assemble in the reverse order of disassembly. Be careful of the following two points.
●
Install the hog rings of seat cushion trim in position, and then
securely connect the trim or trim code with the pad side wire.
●
Clamp the harness in position.
CLIMATE CONTROLLED SEAT
Blower Filter Replacement
Put your hand behind front seat cushion, pull filter downward and
remove it. Replace filter with a new one.
NOTE:
●
When replacing, be sure to set the front seat lifter to the top
position.
●
When installing, do not confuse up-down direction of the filter.
PIIB3357J
PIIB3356J
PIIB6502E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст