Infiniti M35/M45 Y50. Manual — part 960
CHASSIS AND BODY MAINTENANCE
MA-37
C
D
E
F
G
H
I
J
K
M
A
B
MA
Checking Power Steering Fluid and Lines
NLS0008E
Check fluid level in reservoir tank with engine off.
Use “HOT” range at fluid temperatures of 50 to 80
°
C (122 to 176
°
F)
or “COLD” range at fluid temperatures of 0 to 30
°
C (32 to 86
°
F).
CAUTION:
●
Do not overfill.
●
Recommended fluid is genuine NISSAN PSF or equivalent.
Refer to
MA-12, "RECOMMENDED FLUIDS AND LUBRI-
●
Check lines for improper attachment, leaks, cracks, dam-
age, loose connections, chafing and deterioration.
●
Check rack boots for accumulation of power steering fluid.
Axle and Suspension Parts
NLS0008F
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
●
Shake each wheel to check for excessive play.
●
Check wheel bearings for smooth operation.
●
Check axle and suspension nuts and bolts for looseness.
●
Check strut (shock absorber) for oil leakage or other damage.
●
Check suspension ball joint for grease leakage and ball joint
dust cover for cracks or other damage.
SST850C
SST851C
SMA525A
SFA392B
MA-38
CHASSIS AND BODY MAINTENANCE
Drive Shaft
NLS0008G
Check boot and drive shaft for cracks, wear, damage and grease
leakage.
Lubricating Locks, Hinges and Hood Latch
NLS0008H
SFA108A
PIIB6450E
CHASSIS AND BODY MAINTENANCE
MA-39
C
D
E
F
G
H
I
J
K
M
A
B
MA
Checking Seat Belt, Buckles, Retractors, Anchors and Adjusters
NLS0008I
CAUTION:
●
After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in
use during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improp-
erly operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal col-
lision where the driver and passenger air bags are deployed.
●
If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
●
If webbing is cut, frayed, or damaged, replace belt assembly.
●
Never oil tongue and buckle.
●
Use a genuine NISSAN seat belt assembly.
in SB section.
●
Check anchors for loose mounting
●
Check belts for damage
●
Check retractor for smooth operation
●
Check function of buckles and tongues when buckled and released
PIIB3436E
MA-40
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Standard and Limit
NLS0008J
BELT DEFLECTION AND TENSION (VQ35DE)
*: If belt tension gauge cannot be installed at check points shown, check drive belt tension at different location on the belt.
BELT DEFLECTION AND TENSION (VK45DE)
ENGINE COOLANT CAPACITY (APPROXIMATE) (VQ35DE)
Unit:
(US qt, lmp qt)
ENGINE COOLANT CAPACITY (APPROXIMATE) (VK45DE)
Unit:
(US qt, lmp qt)
RADIATOR
Unit: kPa (kg/cm
2
, psi)
ENGINE OIL CAPACITY (APPROXIMATE) (VQ35DE)
Unit:
(US qt, lmp qt)
Deflection adjustment
Unit: mm (in)
Tension adjustment*
Unit: N (kg, lb)
Used belt
New belt
Used belt
New belt
Limit
After adjustment
Limit
After adjustment
Alternator and
power steering
oil pump belt
7 (0.28)
4 - 5
(0.16 - 0.20)
3.5 - 4.5
(0.138 - 0.177)
294 (30, 66)
730 - 818
(74.5 - 83.5,
164 - 184)
838 - 926
(85.5 - 94.5,
188 - 208)
A/C compressor
belt
12 (0.47)
9 - 10
(0.35 - 0.39)
8 - 9
(0.31 - 0.35)
196 (20, 44)
348 - 436
(35.5 - 44.5,
78 - 98)
470 - 559
(48 - 57,
106 - 126)
Applied pushing
force
98 N (10 kg, 22 lb)
—
KBIA1731J
Tension of drive belts
Auto-adjustment by auto tensioner
Engine coolant capacity (With reservoir tank at “MAX” level)
8.9 (9-3/8, 7-7/8)
Reservoir tank engine coolant capacity (At “MAX” level)
0.8 (7/8, 3/4)
Engine coolant capacity (With reservoir tank at “MAX” level)
10.4 (11, 9-1/8)
Reservoir tank engine coolant capacity (At “MAX” level)
0.8 (7/8, 3/4)
Cap relief pressure
Standard
78 - 98 (0.8 - 1.0, 11 - 14)
Limit
59 (0.6, 9)
Leakage testing pressure
157 (1.6, 23)
Drain and refill
With oil filter change
4.7 (5, 4-1/8)
Without oil filter change
4.4 (4-5/8, 3-7/8)
Dry engine (Overhaul)
5.4 (5-3/4, 4-3/4)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст