Infiniti M35/M45 Y50. Manual — part 1159
FRONT WIPER AND WASHER SYSTEM
WW-41
C
D
E
F
G
H
I
J
L
M
A
B
WW
Front Wiper Interval Time Is Not Controlled by Vehicle Speed
NKS003WU
1.
CHECK FUNCTION OF COMBINATION METER
Confirm that speedometer operates normally.
Does the speedometer operate normally?
YES
>> GO TO 2.
NO
>> Combination meter vehicle speed system malfunction. Refer to
2.
CHECK CAN COMMUNICATION BETWEEN BCM AND COMBINATION METER
Select “BCM” on CONSULT-II, and perform self-diagnosis for
“BCM”.
Displayed self-diagnosis results
NO DTC>>Replace BCM. Refer to
BCS-15, "Removal and Installa-
CAN COMM CIRCUIT>>Check CAN communication line of BCM.
Refer to
BCS-13, "CAN Communication Inspection
Using CONSULT-II (Self-Diagnosis)"
.
Front Wiper Intermittent Operation Switch Position Cannot Be Adjusted
NKS003WV
1.
CHECK CIRCUIT BETWEEN COMBINATION SWITCH AND BCM
With CONSULT-ll
1.
Select “BCM” on CONSULT-II, and select “WIPER” on “SELECT
TEST ITEM” screen.
2.
Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “INT VOLUME”, changes in order from 1 to 7
according to wiper switch operation.
Without CONSULT-ll
Refer to
LT-239, "Combination Switch Inspection"
OK or NG
OK
>> Replace BCM. Refer to
BCS-15, "Removal and Installa-
NG
>> Check combination switch (wiper switch). Refer to
239, "Combination Switch Inspection"
.
PKIA7627E
PKIB0110E
WW-42
FRONT WIPER AND WASHER SYSTEM
Wiper Does Not Wipe When Front Washer Operates
NKS003WW
1.
CHECK CIRCUIT BETWEEN COMBINATION SWITCH AND BCM
With CONSULT-ll
1.
Select “BCM” on CONSULT-II, and select “WIPER” on “SELECT
TEST ITEM” screen.
2.
Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “FR WASHER SW” turn ON-OFF according to
front wiper switch operation.
Without CONSULT-ll
Refer to
LT-239, "Combination Switch Inspection"
OK or NG
OK
>> Replace BCM. Refer to
BCS-15, "Removal and Installa-
NG
>> Check combination switch (wiper switch). Refer to
239, "Combination Switch Inspection"
.
Front Wiper Does Not Stop
NKS003WX
1.
CHECK CIRCUIT BETWEEN COMBINATION SWITCH AND BCM
With CONSULT-ll
1.
Select “BCM” on CONSULT-II, and select “WIPER” on “SELECT
TEST ITEM” screen.
2.
Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “FR WIPER INT”, “FR WIPER LOW”, “FR
WIPER HI”, and “FR WASHER SW” turn ON-OFF according to
front wiper switch operation.
Without CONSULT-ll
Refer to
LT-239, "Combination Switch Inspection"
OK or NG
OK
NG
>> Check combination switch (wiper switch). Refer to
LT-239, "Combination Switch Inspection"
.
PKIB0110E
PKIB0110E
FRONT WIPER AND WASHER SYSTEM
WW-43
C
D
E
F
G
H
I
J
L
M
A
B
WW
Removal and Installation of Front Wiper Arms, Adjustment of Wiper Arms Stop
Location
NKS003WY
REMOVAL
1.
Turn wiper switch ON to operate wiper motor, and then turn wiper switch OFF (auto stop).
2.
Open hood, remove arm caps, and remove wiper arm nuts.
3.
Raise wiper arms, and remove wiper arms from the vehicle.
INSTALLATION
1.
Clean up the pivot area as shown in the figure. This will reduce
possibility of wiper arm looseness.
2.
Prior to wiper arm installation, turn on wiper switch to operate
wiper motor and then turn it “OFF” (auto stop).
3.
Push wiper arm onto pivot shaft, paying attention to blind spline.
4.
Lift the blade up and then set it down onto glass surface to set
the blade center to clearance “L1” & “L2” immediately before
tightening nuts.
5.
Spray washer fluid. Turn on wiper switch to operate wiper motor
and then turn it “OFF”.
6.
Make sure that wiper blades stop within clearance “L1” & “L2”.
●
Tighten wiper arm nuts to specified torque.
7.
Attach wiper arm caps.
ADJUSTMENT
Refer to
SEL024J
Clearance “L1”
: 17.9
±
7.5 mm (0.705
±
0.295 in)
Clearance “L2”
: 33.2
±
7.5 mm (1.307
±
0.295 in)
Front wiper arm nuts
: 23.5 N·m (2.4 kg-m, 17 ft-lb)
PKIA9951E
WW-44
FRONT WIPER AND WASHER SYSTEM
Removal and Installation of Front Wiper Drive Assembly
NKS003WZ
REMOVAL
1.
Operate front wiper motor, and stop at the auto stop position.
2.
3.
Remove cowl top cover. Refer to
4.
Disconnect wiper motor connector and remove connector clips.
5.
Remove front wiper drive assembly mounting bolts (A), and
remove front wiper drive assembly (1) from the vehicle.
INSTALLATION
1.
Install front wiper drive assembly to the vehicle.
2.
Connect wiper motor connector. Turn wiper switch ON to operate wiper motor, then turn wiper switch OFF
(auto stop).
3.
Install connector clips to the wiper frame, and install cowl top cover. Refer to
4.
Attach wiper arms. Refer to
5.
Adjustment of wiper arm stop location.
6.
Install arm caps.
Disassembly and Assembly of Front Wiper Drive Assembly
NKS003X0
SKIB4222E
Front wiper drive assembly mounting bolts
: 4.5 N·m (0.46kg-m, 40 in-lb)
1.
Wiper linkage 1
2.
Bolt
3.
Shaft seal
4.
Wiper motor
5.
Wiper frame
6.
Bolt
7.
Wiper linkage 2
: N·m (kg-m, in-lb)
: Should be lubricated with grease.
SKIB4231E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст