Infiniti M35/M45 Y50. Manual — part 464
DTC P0172, P0175 FUEL INJECTION SYSTEM FUNCTION
EC-329
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
8.
CHECK FUNCTION OF FUEL INJECTOR-I
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Disconnect harness connectors F221 (1), F33 (2).
–
: vehicle front
–
Cylinder head (bank 2) (3)
3.
Turn ignition switch ON.
4.
Check voltage between harness connector F33 terminal 5 and
ground with CONSULT-II or tester.
5.
Turn ignition switch OFF.
6.
Disconnect ECM harness connector.
7.
Check harness continuity between the following terminals.
8.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 9.
NG
>> Perform trouble diagnosis for FUEL INJECTOR, refer to
PBIB2785E
Voltage: Battery voltage
Cylinder
Harness connector F33 terminal
ECM terminal
1
6
23
2
4
42
3
2
22
4
3
41
5
1
21
6
7
40
Continuity should exist.
PBIB2323E
EC-330
[VQ35DE]
DTC P0172, P0175 FUEL INJECTION SYSTEM FUNCTION
9.
CHECK FUNCTION OF FULE INJECTOR-II
Provide battery voltage between the following terminals, and then
interrupt it. Listen to each fuel injector operating sound.
OK or NG
OK
>> GO TO 10.
NG
>> Perform trouble diagnosis for FUEL INJECTOR, refer to
10.
CHECK FUEL INJECTOR
1.
Remove fuel injector assembly. Refer to
EM-47, "FUEL INJECTOR AND FUEL TUBE"
Keep fuel hose and all fuel injectors connected to fuel tube.
2.
Confirm that the engine is cooled down and there are no fire hazards near the vehicle.
3.
Reconnect all harness connectors disconnected.
4.
Disconnect all fuel injector harness connectors.
5.
Disconnect all ignition coil harness connectors.
6.
Prepare pans or saucers under each fuel injectors.
7.
Crank engine for about 3 seconds.
Make sure fuel does not drip from fuel injector.
OK or NG
OK (Does not drip.)>>GO TO 11.
NG (Drips.)>>Replace the fuel injectors from which fuel is dripping. Always replace O-ring with new one.
11.
CHECK INTERMITTENT INCIDENT
Refer to
EC-153, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Cylinder
Harness connector F221 terminal
(+)
(–)
1
5
6
2
4
3
2
4
3
5
1
6
7
Operating sound should exist.
PBIB2497E
DTC P0181 FTT SENSOR
EC-331
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0181 FTT SENSOR
PFP:22630
Component Description
NBS004Y0
The fuel tank temperature sensor (3) is used to detect the fuel tem-
perature inside the fuel tank. The sensor modifies a voltage signal
from the ECM. The modified signal returns to the ECM as the fuel
temperature input. The sensor uses a thermistor which is sensitive to
the change in temperature. The electrical resistance of the ther-
mistor decreases as temperature increases.
●
Fuel level sensor unit and fuel pump (1)
●
Fuel pressure regulator (2)
<Reference data>
*: This data is reference value and is measured between ECM terminal 107 (Fuel
tank temperature sensor) and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output
voltage. Doing so may result in damage to the ECM's transistor.
Use a ground other than ECM terminals, such as the ground.
On Board Diagnosis Logic
NBS004Y1
DTC Confirmation Procedure
NBS004Y2
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Wait at least 10 seconds.
If the result is NG, go to
EC-334, "Diagnostic Procedure"
If the result is OK, go to following step.
4.
Check “COOLAN TEMP/S” value.
If “COOLAN TEMP/S” is less than 60
°
C (140
°
F), the result will
be OK.
If “COOLAN TEMP/S” is above 60
°
C (140
°
F), go to the following
step.
5.
Cool engine down until “COOLAN TEMP/S” is less than 60
°
C
(140
°
F).
6.
Wait at least 10 seconds.
7.
If 1st trip DTC is detected, go to
EC-334, "Diagnostic Procedure"
PBIB2707E
Fluid temperature
°
C (
°
F)
Voltage*
V
Resistance
k
Ω
20 (68)
3.5
2.3 - 2.7
50 (122)
2.2
0.79 - 0.90
SEF012P
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0181
0181
Fuel tank temperature
sensor circuit range/
performance
Rationally incorrect voltage from the sensor is
sent to ECM, compared with the voltage sig-
nals from engine coolant temperature sensor
and intake air temperature sensor.
●
Harness or connectors
(The sensor circuit is open or shorted)
●
Fuel tank temperature sensor
SEF174Y
EC-332
[VQ35DE]
DTC P0181 FTT SENSOR
WITH GST
Follow the procedure “WITH CONSULT-II” above.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст