Infiniti M35/M45 Y50. Manual — part 216
DIAGNOSIS SYSTEM
AV-241
[WITH MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
AV
Rear View Monitor Guiding Line Adjustment
NKS004B0
1.
Draw lines on rearward area of the vehicle passing through the
following points: 20 cm (7.87 in) from both sides of the vehicle,
and 0.5 m (1.64 ft), 1.0 m (3.28 ft) from the rear end of the
bumper.
2.
Set into “Adjust offset of rear view camera” mode of Confirma-
tion/Adjustment mode.
3.
Rotate the center dial, and then select the guiding line pattern so
that its angle is aligned with the correction line of the rear of the
vehicle.
4.
Make fine adjustment to the correction line of the rear of the vehicle with up/down/left/right switches so
that its position is aligned with the guiding line. Press “OK” switch and record the adjusted guiding line
position to the camera control unit.
CAUTION:
Never operate other function such as pressing BACK while writing index data.
If Confirmation/Adjustment mode does not function in the above procedure, perform one of the
following service to adjust the index again.
●
Remove battery for five min. Then reconnect battery.
●
Remove camera control unit connector for five min. Then reconnect camera control unit con-
nector.
SKIB3691E
Selected pattern
: 7
SKIB3689E
Up/Down adjustment range
: –20 - 20
Left/Right adjustment range
: –20 - 20
AV-242
[WITH MOBILE ENTERTAINMENT SYSTEM]
DIAGNOSIS SYSTEM
CONSULT-II Functions (Multi AV)
NKS004B1
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
OPERATION PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1.
Turn ignition switch OFF.
2.
Connect CONSULT-II and CONSULT-II CONVERTER to data
link connector, and turn ignition switch ON.
3.
Touch “START (NISSAN BASED VHCL)”.
4.
Touch “MULTI AV”
If “MULTI AV” is not indicated, check the following item.
●
AV (NAVI) control unit power supply and ground circuit.
●
CONSULT-II data link connector (DLC) circuit
Refer to
LAN-42, "Precautions When Using CONSULT-II"
Diagnosis mode
Description
SELF DIAG RESULTS
●
Performs the connection diagnosis of communication circuit between AV (NAVI) control unit
and system and displays the current and past malfunctions collectively.
●
The DVD-ROM drive diagnosis of NAVI control unit and the connection diagnosis between
NAVI control unit and GPS antenna can be performed (DVD-ROM drive will not be diagnosed
when no map DVD-ROM is in it)
DATA MONITOR
The diagnosis of vehicle signal that input to the AV (NAVI) control unit can be performed
CAN DIAG SUPPORT MNTR
The transmitting/receiving of CAN communication can be monitored. Refer to
AV COMM MONITOR
The transmitting/receiving of a system can be monitored
ECU PART NUMBER
The part number of AV (NAVI) control unit can be checked
SKIB3794E
BCIA0029E
BCIA0030E
DIAGNOSIS SYSTEM
AV-243
[WITH MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
AV
5.
Select diagnosis item on “SELECT DIAG MODE” screen.
SELF-DIAG RESULTS
The self-diagnosis is started and self-diagnostic results are dis-
played by touching “START” after selecting “SELF-DIAG RESULTS”.
●
In CONSULT-II self-diagnosis, self-diagnostic results and error
history are displayed collectively.
●
The current malfunction indicates “CRNT”. The past malfunction
indicates “PAST”.
●
If DTC [U1000], [U1300] are detected, “0” is displayed at TIME.
If it is normal the next time ignition switch is ON of next time, add
1 to the TIME.
Display Item of Self-Diagnostic Results
Self-diagnostic results may be displayed simultaneously according to the cause. If some error items are dis-
played simultaneously, the detection of the cause can be performed by the combination of display items
BCIA0031E
SKIB3674E
Error item
Description
Possible cause/Action to take
CAN_COMM_CIRCUIT [U1000]
CAN communication malfunction is
detected
Print out the self-diagnostic results and go
to
LAN-42, "Precautions When Using
.
CONTROL UNIT (CAN) [U1010]
CAN initial diagnosis malfunction is
detected
Replace AV (NAVI) control unit
Refer to
AV-282, "AV (NAVI) Control Unit"
CONTROL UNIT (AV) [U1310]
AV communication circuit initial diagno-
sis malfunction is detected
Replace AV (NAVI) control unit
Refer to
AV-282, "AV (NAVI) Control Unit"
●
AV COMM CIRCUIT [U1300]
●
SWITCH CONN [U1240]
●
VIDEO DIST CONN [U1246]
●
DVD DECK CONN [U1248]
●
AUDIO H/U CONN [U1249]
●
AMP CONN [U124E]
●
REAR CAMERA CONN [U1252]
Malfunction is detected on communi-
cation circuit between AV (NAVI) con-
trol unit and video distributor
●
Communication circuit between AV
(NAVI) control unit and video distributor
●
AV (NAVI) control unit
●
Video distributor
●
AV COMM CIRCUIT [U1300]
●
SWITCH CONN [U1240]
●
DVD DECK CONN [U1248]
●
AUDIO H/U CONN [U1249]
●
AMP CONN [U124E]
●
REAR CAMERA CONN [U1252]
Malfunction is detected on communi-
cation circuit between video distributor
and DVD player
●
Communication circuit between video
distributor and DVD player
●
Video distributor
●
DVD player
●
AV COMM CIRCUIT [U1300]
●
SWITCH CONN [U1240]
●
AUDIO H/U CONN [U1249]
●
AMP CONN [U124E]
●
REAR CAMERA CONN [U1252]
Malfunction is detected on communi-
cation circuit between DVD player and
multifunction switch
●
Communication circuit between DVD
player and multifunction switch
●
DVD player
●
Multifunction switch
AV-244
[WITH MOBILE ENTERTAINMENT SYSTEM]
DIAGNOSIS SYSTEM
●
AV COMM CIRCUIT [U1300]
●
AUDIO H/U CONN [U1249]
●
AMP CONN [U124E]
●
REAR CAMERA CONN [U1252]
Malfunction is detected on communi-
cation circuit between multifunction
switch and camera control unit
●
Communication circuit between multi-
function switch and camera control unit
●
Multifunction switch
●
Camera control unit
●
AV COMM CIRCUIT [U1300]
●
AUDIO H/U CONN [U1249]
●
AMP CONN [U124E]
●
Malfunction is detected on communi-
cation circuit between camera con-
trol unit and BOSE amp
●
Communication circuit between camera
control unit and BOSE amp
●
Camera control unit
●
BOSE amp
●
AV COMM CIRCUIT [U1300]
●
AUDIO H/U CONN [U1249]
With rear control switch
●
Audio unit power supply and ground
circuit malfunction is detected
●
Malfunction is detected on communi-
cation circuit between BOSE amp
and rear control switch
●
Malfunction is detected on communi-
cation circuit between rear control
switch and audio unit
●
Malfunction is detected on communi-
cation signal between audio unit and
AV (NAVI) control unit
●
Communication circuit between BOSE
amp and rear control switch
●
Communication circuit between rear
control switch and audio unit
●
BOSE amp
●
Rear control switch
●
Audio unit
●
AV (NAVI) control unit
Without rear control switch
●
Audio unit power supply and ground
circuit malfunction is detected
●
Malfunction is detected on communi-
cation circuit between BOSE amp
and audio unit
●
Malfunction is detected on communi-
cation signal between audio unit and
AV (NAVI) control unit
●
Audio unit power supply and ground cir-
cuit
●
Communication circuit between BOSE
amp and audio unit
●
Audio unit
●
AV (NAVI) control unit
●
BOSE amp
●
AV COMM CIRCUIT [U1300]
●
VIDEO DIST CONN [U1246]
●
Video distributor power supply and
ground circuit malfunction is
detected
●
Malfunction is detected on communi-
cation signal between video distribu-
tor and AV (NAVI) control unit
●
Video distributor power supply and
ground circuit
●
Video distributor
●
AV (NAVI) control unit
●
AV COMM CIRCUIT [U1300]
●
REAR CAMERA CONN [U1252]
●
Camera control unit power supply
and ground circuit malfunction is
detected
●
Malfunction is detected on communi-
cation signal between camera con-
trol unit and AV (NAVI) control unit
●
Camera control unit power supply and
ground circuit
●
Camera control unit
●
AV (NAVI) control unit
●
AV COMM CIRCUIT [U1300]
●
SWITCH CONN [U1240]
●
Multifunction switch power supply
and ground circuit malfunction is
detected
●
Malfunction is detected on communi-
cation signal between multifunction
switch and AV (NAVI) control unit
●
Multifunction switch power supply and
ground circuit
●
Multifunction switch
●
AV (NAVI) control unit
●
AV COMM CIRCUIT [U1300]
●
DVD DECK CONN [U1248]
●
DVD player power supply and
ground circuit malfunction is
detected
●
Malfunction is detected on communi-
cation signal between DVD player
and AV (NAVI) control unit
●
DVD player power supply and ground
circuit
●
DVD player
●
AV (NAVI) control unit
Error item
Description
Possible cause/Action to take
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст