Infiniti M35/M45 Y50. Manual — part 646
DTC P0222, P0223 TP SENSOR
EC-1057
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
Diagnostic Procedure
NBS005G0
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten ground screws on the body.
Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
47
G
Sensor power supply
(Throttle position sensor)
[Ignition switch: ON]
Approximately 5V
50
W
Throttle position sensor 1
[Ignition switch: ON]
●
Engine: Stopped
●
Selector lever: D
●
Accelerator pedal: Fully released
More than 0.36V
[Ignition switch: ON]
●
Engine: Stopped
●
Selector lever: D
●
Accelerator pedal: Fully depressed
Less than 4.75V
66
B
Sensor ground
(Throttle position sensor)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 0V
69
R
Throttle position sensor 2
[Ignition switch: ON]
●
Engine: Stopped
●
Selector lever: D
●
Accelerator pedal: Fully released
Less than 4.75V
[Ignition switch: ON]
●
Engine: Stopped
●
Selector lever: D
●
Accelerator pedal: Fully depressed
More than 0.36V
91
BR
Sensor power supply
(APP sensor 2)
[Ignition switch: ON]
Approximately 5V
1.
Body ground M70
2.
Body ground M16
PBIB2782E
EC-1058
[VK45DE]
DTC P0222, P0223 TP SENSOR
2.
CHECK THROTTLE POSITION SENSOR 1 POWER SUPPLY CIRCUIT-I
1.
Disconnect electric throttle control actuator (1) harness connec-
tor.
–
Illustration shows the view with intake air duct removed.
2.
Turn ignition switch ON.
3.
Check voltage between electric throttle control actuator terminal
1 and ground with CONSULT-II or tester.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 3.
3.
CHECK THROTTLE POSITION SENSOR 1 POWER SUPPLY CIRCUIT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between electric throttle control actuator terminal 1 and ECM terminal 47.
Refer to Wiring Diagram.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit.
4.
CHECK THROTTLE POSITION SENSOR 1 POWER SUPPLY CIRCUIT-III
Check harness for short to power and short to ground, between the following terminals.
OK or NG
OK
>> GO TO 5.
NG
>> Repair short to ground or short to power in harness or connectors.
5.
CHECK APP SENSOR
Refer to
EC-1349, "Component Inspection"
OK or NG
OK
>> GO TO 11.
NG
>> GO TO 6.
PBIB2690E
Voltage: Approximately 5V
PBIA9580J
Continuity should exist.
ECM terminal
Sensor terminal
Reference Wiring Diagram
47
Electric throttle control actuator terminal 1
91
APP sensor terminal 5
DTC P0222, P0223 TP SENSOR
EC-1059
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
6.
REPLACE ACCELERATOR PEDAL ASSEMBLY
1.
Replace accelerator pedal assembly.
2.
Perform
EC-788, "Accelerator Pedal Released Position Learning"
3.
Perform
EC-788, "Throttle Valve Closed Position Learning"
4.
Perform
EC-788, "Idle Air Volume Learning"
>> INSPECTION END
7.
CHECK THROTTLE POSITION SENSOR 1 GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between electric throttle control actuator terminal 4 and ECM terminal 66.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 8.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
8.
CHECK THROTTLE POSITION SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal 50 and electric throttle control actuator terminal 2.
Refer to Wiring Diagram.
2.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 9.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
9.
CHECK THROTTLE POSITION SENSOR
Refer to
EC-1060, "Component Inspection"
.
OK or NG
OK
>> GO TO 11.
NG
>> GO TO 10.
10.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace the electric throttle control actuator.
2.
Perform
EC-788, "Throttle Valve Closed Position Learning"
3.
Perform
EC-788, "Idle Air Volume Learning"
>> INSPECTION END
11.
CHECK INTERMITTENT INCIDENT
Refer to
EC-857, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
>> INSPECTION END
Continuity should exist.
Continuity should exist.
EC-1060
[VK45DE]
DTC P0222, P0223 TP SENSOR
Component Inspection
NBS005G1
THROTTLE POSITION SENSOR
1.
Reconnect all harness connectors disconnected.
2.
Perform
EC-788, "Throttle Valve Closed Position Learning"
.
3.
Turn ignition switch ON.
4.
Set selector lever to D position.
5.
Check voltage between ECM terminals 50 (TP sensor 1 signal),
69 (TP sensor 2 signal) and ground under the following condi-
tions.
6.
If NG, replace electric throttle control actuator and go to the next
step.
7.
Perform
EC-788, "Throttle Valve Closed Position Learning"
.
8.
Perform
EC-788, "Idle Air Volume Learning"
.
Removal and Installation
NBS005G2
ELECTRIC THROTTLE CONTROL ACTUATOR
Refer to
Terminal
Accelerator pedal
Voltage
50
(Throttle position sensor 1)
Fully released
More than 0.36V
Fully depressed
Less than 4.75V
69
(Throttle position sensor 2)
Fully released
Less than 4.75V
Fully depressed
More than 0.36V
PBIB1530E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст