Infiniti M35/M45 Y50. Manual — part 750
SIDE GUARD MOLDING
EI-31
C
D
E
F
G
H
J
K
L
M
A
B
EI
SIDE GUARD MOLDING
PFP:76840
Removal and Installation
NIS0024R
REMOVAL
1.
Apply masking tape around outer circumference of side guard molding.
2.
Remove double-faced adhesive tapes with (wide) resin spatula. Disengage clips and remove side guard
molding (front / rear).
INSTALLATION
1.
Remove double-faced adhesive tape remaining on vehicle.
2.
Clean contact surface of vehicle (to side guard molding), and install side guard molding to specified holes.
NOTE:
To re-use side guard molding, follow above steps 1 and 2 as well; clean surface after removing double-
faced adhesive tape, apply new double-faced adhesive tape and then install side guard molding to vehi-
cle.
CAUTION:
●
Do not let air between contact surfaces when installing.
●
To secure contact, do not wash vehicle within 24 hours after installation.
1.
Side guard molding (front)
2.
Side guard molding (rear)
3.
Specified holes
PIIB2937J
EI-32
DOOR PARTING SEAL
DOOR PARTING SEAL
PFP:80838
Removal and Installation
NIS0024S
FRONT DOOR PARTING SEAL
Removal
1.
Fully open front door.
2.
Remove front door parting seal (front side) mounting plastic clips.
3.
Disengage the joint between front door parting seal (front side) and front door panel, and then remove
front door parting seal (front side).
4.
Disengage front door parting seal (lower side) mounting plastic clips, and then remove front door parting
seal (lower side).
Installation
Install in the reverse order of removal.
REAR DOOR PARTING SEAL
Removal
1.
Fully open rear door.
2.
Disengage the joint between rear door parting seal (front side) and rear door panel, and then remove rear
door parting seal (front side).
3.
Disengage rear door parting seal (lower side) mounting plastic clips, and then remove rear door parting
seal (lower side).
Installation
Install in the reverse order of removal.
1.
Front door parting seal (front side)
2.
Front door parting seal (lower side)
3.
Rear door parting seal (lower side)
4.
Rear door parting seal (front side)
5.
Door inner panel
PIIB3974J
TRUNK LID FINISHER
EI-33
C
D
E
F
G
H
J
K
L
M
A
B
EI
TRUNK LID FINISHER
PFP:84810
Removal and Installation
NIS0024T
REMOVAL
1.
Fully open trunk lid.
2.
Remove trunk lid finisher inner. Refer to
EI-57, "REMOVAL AND INSTALLATION OF TRUNK LID FIN-
3.
Remove trunk lid finisher upper mounting nuts.
4.
Disconnect back lamp, license lamp and trunk opener switch harness connector.
5.
Remove double-faced adhesive tapes with (wide) plastic spatula.Disconnect clips and remove trunk lid
finisher outer.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
Replace double-faced adhesive tape on back of finisher with a new tape if trunk lid finisher outer is
reused.
●
Remove double-faced adhesive tape remaining on body and back of finisher using double-faced
adhesive tape remover when removing finisher outer.
●
Install after cleaning adhesive parts of body side and back of finisher outer.
●
Do not wash the vehicle with in 24 hours after installing so as to keep adhesive.
1.
Trunk lid finisher outer
PIIB4516E
EI-34
DOOR FINISHER
DOOR FINISHER
PFP:80900
Removal and Installation
NIS0024U
FRONT AND REAR DOOR FINISHER
Removal
1.
Fully open door window.
2.
Remove inside handle escutcheon and remove screw.
3.
Remove arm rest finisher.
4.
Remove screw of armrest finisher portion.
1.
Inside handle escutcheon
2.
Armrest finisher
3.
Front door finisher
4.
Rear door finisher
5.
Step lamp
6.
Seat memory switch
7.
Front door sash cover inner
8.
Rear door sash cover inner
Clip
Metal clip
PIIB4931E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст