Infiniti M35/M45 Y50. Manual — part 547
ASCD BRAKE SWITCH
EC-661
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
3.
CHECK ASCD BRAKE SWITCH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ASCD brake switch (2) harness connector.
–
Stop lamp switch (1)
3.
Turn ignition switch ON.
4.
Check voltage between ASCD brake switch terminal 1 and
ground with CONSULT-II or tester.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
●
Fuse block (J/B) connector E102
●
10A fuse
●
Harness for open or short between ASCD brake switch and fuse
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 108 and ASCD brake switch terminal 2.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E108, M15
●
Harness for open or short between ECM and ASCD brake switch
>> Repair open circuit or short to ground or short to power in harness or connectors.
PBIB2705E
Voltage: Battery voltage
PBIB0857E
Continuity should exist.
EC-662
[VQ35DE]
ASCD BRAKE SWITCH
7.
CHECK ASCD BRAKE SWITCH
Refer to
EC-663, "Component Inspection"
OK or NG
OK
>> GO TO 13.
NG
>> Replace ASCD brake switch.
8.
CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect stop lamp switch (1) harness connector.
–
ASCD brake switch (2)
3.
Check voltage between stop lamp switch terminal 1 and ground
with CONSULT -II or tester.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 9.
9.
DETECT MALFUNCTIONING PART
Check the following.
●
Fuse block (J/B) connector E101
●
10A fuse
●
Harness for open or short between stop lamp switch and battery
>> Repair open circuit or short to ground or short to power in harness or connectors.
10.
CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Disconnect ECM harness connector.
2.
Check harness continuity between ECM terminal 101 and stop lamp switch terminal 2.
Refer to Wiring Diagram.
3.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 12.
NG
>> GO TO 11.
PBIB2705E
Voltage: Battery voltage
PBIA9488J
Continuity should exist.
ASCD BRAKE SWITCH
EC-663
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
11.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E108, M15
●
Harness for open or short between ECM and stop lamp switch
>> Repair open circuit or short to ground or short to power in harness or connectors.
12.
CHECK STOP LAMP SWITCH
Refer to
EC-663, "Component Inspection"
OK or NG
OK
>> GO TO 13.
NG
>> Replace stop lamp switch.
13.
CHECK INTERMITTENT INCIDENT
Refer to
EC-153, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
>> INSPECTION END
Component Inspection
NBS0058L
ASCD BRAKE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect ASCD brake switch harness connector.
3.
Check harness continuity between ASCD brake switch terminals
1 and 2 under the following conditions.
4.
If NG, adjust ASCD brake switch installation, refer to
STOP LAMP SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect stop lamp switch harness connector.
3.
Check harness continuity between stop lamp switch terminals 1
and 2 under the following conditions.
4.
If NG, adjust stop lamp switch installation, refer to
Condition
Continuity
Brake pedal: Fully released.
Should exist.
Brake pedal: Slightly depressed.
Should not exist.
PBIB1536E
Condition
Continuity
Brake pedal: Fully released.
Should not exist.
Brake pedal: Slightly depressed.
Should exist.
PBIA9489J
EC-664
[VQ35DE]
ASCD INDICATOR
ASCD INDICATOR
PFP:24814
Component Description
NBS0058M
ASCD indicator lamp illuminates to indicate ASCD operation status. Lamp has two indicators, CRUISE and
SET, and is integrated in combination meter.
CRUISE lamp illuminates when MAIN switch on ASCD steering switch is turned ON to indicated that ASCD
system is ready for operation.
SET lamp illuminates when following conditions are met.
●
CRUISE lamp is illuminated.
●
SET/COAST switch on ASCD steering switch is turned ON while vehicle speed is within the range of
ASCD setting.
SET lamp remains lit during ASCD control.
Refer to
EC-36, "AUTOMATIC SPEED CONTROL DEVICE (ASCD)"
for the ASCD function.
CONSULT-II Reference Value in Data Monitor Mode
NBS0058N
Specification data are reference values.
MONITOR ITEM
CONDITION
SPECIFICATION
CRUISE LAMP
●
Ignition switch: ON
MAIN switch: Pressed at the 1st time
→
at the 2nd time
ON
→
OFF
SET LAMP
●
MAIN switch: ON
●
When vehicle speed is between
40 km/h (25 MPH) and 144 km/h
(89 MPH)
ASCD: Operating
ON
ASCD: Not operating
OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст